Loading ...
Loading ...
Loading ...
4 / 4
Removing the lock from the network
Follow your smart home system’s instructions
to remove the lock from the network. When
prompted by the system, press button A” on the
lock interior once.
© 2018 Spectrum Brands, Inc.
1. Read all instructions in their entirety.
2. Familiarize yourself with all warning and caution statements.
3. Remind all family members of safety precautions.
4. Restrict access to your lock’s back panel and routinely check your settings to
ensure they have not been altered without your knowledge.
5. Dispose of used batteries according to local laws and regulations.
CAUTION: Prevent unauthorized entry. Restrict access to your lock's back panel and
routinely check your settings to ensure they have not been altered without your
knowledge.
WARNING: This Manufacturer advises that no lock can provide complete security
by itself. This lock may be defeated by forcible or technical means, or evaded by
entry elsewhere on the property. No lock can substitute for caution, awareness of
your environment, and common sense. Builder’s hardware is available in multiple
performance grades to suit the application. In order to enhance security and reduce
risk, you should consult a qualiied locksmith or other security professional.
Network Information Important Safeguards
ZWave System Notes
This product is a security enabled ZWave Plus product and must be used with a Security
Enabled ZWave controller to be fully utilized. ZWave is a “Wireless mesh network,” and
results may vary based on building construction and communication path.
To assure interoperability, each ZWave product must pass a stringent conformance test to
assure that it meets the ZWave standard for complete compliance with all other devices and
controls. The ZWave identity mark assures consumers, integrators, dealers and manufacturers
that their products will reliably perform with any other ZWave device. And, regardless of the
vendor, always powered nodes may act as a repeater for Kwikset/Weiser/Baldwin products.
ZWave Coniguration and Association Parameters are available on the Signature
Series Deadbolt with Home Connect (2nd Gen.) page at www.kwikset.com.
ZWave
Controller
12"
305 mm
ZWave
Controller
12"
305 mm
Deadbolt Interior at a Glance
Reference Guide
Status LED Notiications Factory Reset
Troubleshooting: Adding the Lock to a Smart Home System
A factory reset will remove the lock from your smart home system.
1 Remove battery pack. 2 Press and HOLD the
Program button while
reinserting the battery pack.
Keep holding the button
for 30 seconds until
the lock beeps and the
status LED lashes red.
3 Press the Program
button once more. When
the LED lashes green
and you hear two beeps,
the lock has been reset.
4 Perform the door handing process again to
teach the lock the orientation of the door, and
pair the lock with your smart home system.
Status
LED
Back panel
Some ZWave® systems require that the lock be within 12" of the controller during the adding process.
If this is the case, follow the steps below to remove the lock interior from the door to perform the process closer to the controller:
1 Remove the small screws that secure the interior assembly to the
mounting plate.
2 Remove the interior assembly from the door. 3 Hold the interior assembly a maximum of 12" (305 mm) from your
smart home controller for the rest of this process.
4 Initiate the process to add the lock to your system at your smart
home controller. Refer to your smart home system instructions for
more information.
5 When prompted by your smart home system to add the lock, press
button “A” on the lock interior one time. The red LED will illuminate
when the lock enters Add Mode.
6 Once successful, re-name the lock in your system (if applicable).
Then, reinstall the lock interior on the interior assembly.
Please allow time for the controller to add the lock.
These features can be adjusted in some smart home apps.
Switches
1. Status LED
Door lock status LED blinks every 6 seconds. ON position is factory default.
2. Auto-Lock
Automatically re-locks door 30 seconds after unlocking. OFF position is factory default.
CAUTION: With this feature
enabled, it is possible to lock
yourself outside.
3. Audio
Beeping sound is heard during programming and normal
operation. ON position is factory default.
4. Invert
Only used if the Status LED is communicating the opposite door lock status.
on o
1 2 3 4
Amber lash
Door is locked.
Green lash
Door is unlocked.
Red lash
The 4 AA batteries in the
interior are low and need
to be replaced.
Amber
LED
Green
LED
Red
LED
Program
button
Status
LED
Switches
Turnpiece
shaft
Note: When the cover is
removed, the turnpiece shaft
can be used to manually lock
and unlock the door.
Button “A” Button “B”