Loading ...
Loading ...
Loading ...
GB4
AFTER-SALES SERVICE
Before calling the After-sales Service:
1. See if you can solve the problem yourself with the help of the suggestions given in the “Troubleshooting guide”.
2. Switch the appliance o and back on again it to see if the fault persists.
If after the above checks the fault still occurs, get in touch with the nearest After-sales Service.
Always specify:
• A brief description of the fault;
• The exact type and model of the appliance;
• The service number (number after the word “Service” on the rating plate), located on the inside of the appliance. The service number is also indicated on the
guarantee booklet;
• Your full address;
• Your telephone number.
If any repairs are required, please contact an authorised After-sales Service (to guarantee that original spare parts will be used and repairs carried out correctly).
CLEANING
WARNING:
- Do not use steam cleaners.
- Disconnect the appliance from the power supply
IMPORTANT: Do not use corrosive or abrasive detergents. If any of these products accidentally comes into contact with the appliance, clean it
immediately with a damp cloth.
• Clean the surfaces with a damp cloth. If it is very dirty, add a few drops of washing up detergent to the water. Finish o with a dry cloth.
IMPORTANT: do not use abrasive sponges or metallic scrapers or scouring pads. Over time, these can ruin the enamel surface.
• Use detergents specically designed for cleaning the appliance and follow the manufacturer instructions.
IMPORTANT: clean the lters at least monthly to remove any oil or grease residuals.
EXTRACTOR OR FILTERING HOOD INSTALLATION
Pre-assemble the steam deector on the motor assembly:
(a.) t the two side nuts on the lower internal side of the cooker hood.
(b.) t the steam deector to the motor assembly, (c.) secure with 2 M6 x 20 screws and 2 Ø 14 x 12 bushings.
Pre-assembly of the electrical connection box:
(d.) remove the screws and washers on the extractor unit and remove the adhesive tape xing the box to the extractor unit,
(e.) position the electrical connection box above the extractor unit, (f.) secure with 2 Ø 3.5 x 9.5 screws and 2 Ø 14 x 12 washers (previously removed).
1. Using a pencil, draw the centre line on the wall up to the ceiling to facilitate installation operations.
2. Apply the drilling template to the wall: Align the vertical centre-line on the drilling template with the centre-line drawn on the wall. The template’s bottom
edge represents the bottom edge of the hood.
3. Drill as shown on the template, insert the wall plugs and screw in the top 2 screws, leaving a space of approx. 1 cm between the screw head and the wall.
Note: Drill all the holes indicated on the template: the top 2 holes are for hanging the hood and the bottom hole is for xing it securely to the wall.
4. Fit the ue support bracket “G” to the wall and against the ceiling, use the support bracket as a drilling diagram (if present, the small slot on the support must
match the line previously drawn on the wall) and mark 2 holes with the pencil, then drill the holes and insert 2 wall plugs.
5. Fix the ue support bracket to the wall with 2 screws.
6. Hang the hood on the 2 top screws.
7. 7. Screw in the bottom screw (and washer!) to x the hood securely in place (COMPULSORY!!). After checking the alignment of the hood, TIGHTEN ALL THE
SCREWS - top and bottom.
Note: the bottom xing, positioned in the centre, is visible upon removal of the grease lter and the carbon lter frame (if present).
8. Connect an exhaust pipe (pipe and clamps are not supplied and must be bought separately) to the collar above the extraction motor unit.
For extractor operation, connect the other end of the exhaust pipe to the home discharge device.
For lter operation, x the deector F to the ue support bracket G and connect the other end of the exhaust pipe to the deector collar F.
9. Make all necessary electrical connections.
10. Fit the ues over the extractor unit, engaging them in their seat above the hood.
11. Slide the top section of the ue and secure it with 2 screws (11a) to the ue support bracket “G” (11b).
Ret the carbon lter frame and the grease lter/s and check for correct hood operation.
Loading ...
Loading ...
Loading ...