PORS668RW User Manual

32 33

INSTALLATIONSOLVING PROBLEMS

faults

Ifthereisaproblemwiththeovenand/orgrill,please:

• Checkthepointslistedbelowbeforecallingforservice.

Itmaybepossibletoavoidacallbyxingtheproblem

yourself - and so continue cooking�

• Forcookingproblemsrefertopage24.





problem possible cause

oven or grill not working

Time of day not set�

Power not turned on�

Controls are incorrectly set�

Household fuse has blown or power supply is off�

Child-proof oven lock activated� (Refer to operating instructions)�



oven light not working

Lamp blown or loose in socket�

Household fuse has blown�



oven not heating enough

Foil or trays on bottom of oven�

oven not working

Timer is in “AUTO” mode� (Refer to timer operating instructions)

Household fuse has blown�



timer ﬂashing on display

Power failure or interruption�



unit smoking when ﬁrst used

Protective oils being removed�

condensation building up

Reduce amount of water used in cooking� (Some condensation is normal)�

door cannot be replaced after

removal

Stirrup not engaged properly�



warning

IMPORTANT: This appliance must be properly

earthed.

• Donotlifttheappliancebythedoorhandles.

• Preparethecupboardopeningtomatchyourappliance

measurements� (See diagrams on following pages)�

• Slideapplianceintothecupboard,ensuringthatthe

supply cable (where ﬁtted) does not kink�

• Topreventtipping,usethescrewssuppliedtosecure

your oven into the cupboard� Use just 2 screws for single

cavity ovens and 4 screws for dual cavity� Remove the

bottom door in dual cavity ovens to provide access to the

bottom 2 screwing points (see illustrations on page 30

and 32)�

• Forappliancesttedwithaexiblesupplycord,ifthe

cord is damaged, it must be replaced by the manufacturer

or its service agent or similarly qualiﬁed person in order

to avoid a hazard� The plug must be accessible after

installation�

• Wheretheapplianceisbuiltintoacabinet,thecabinet

material must be capable of withstanding 70°C�

Installationintolowtemperaturetolerantcabinetry(e.g.

vinyl coated) may result in deterioration of the low

temperature coating by discolouring or bubbling�

• Iftheapplianceisinstalledadjacenttovinyl-wrapped

surfaces, use an installation kit available from the vinyl-

wrap supplier�

• ElectroluxHomeProductscannotacceptresponsibility

for damage caused by installation into low temperature

tolerant cabinets�

• Afterinstallation,testandensurethattheappliance

operates correctly before handing it over to the customer�

caution

To avoid any potential hazard, you must follow our

instructions below when you install your appliance� Failure to

install the appliance correctly could invalidate any warranty

or liability claims and lead to prosecution�

warning

USE AN AUTHORISED PERSON

As stated in the local municipal building codes and other

relevant statutory regulations�

• WiringconnectionsmustbeinaccordancewithAS/NZS

3000 Wiring Rules and any particular conditions of the

local authority�

• Refertodataplateforratinginformationandcircuit

diagram� The data plate is positioned behind the bottom

of the oven door� The circuit diagram is positioned on the

top panel of the appliance�

• Forapplianceswithopencookingsurfaces,anallpole

disconnected functional switch should be provided near

theapplianceinanaccessibleposition.RefertoAS/NZS

3000 clause 4�7�1

• Wiringshouldbeprotectedagainstmechanicalfailure.

RefertoAS/NZS3000clauses3.3.2.6,3.9,3.10

• Ameansofdisconnectionwithacontactseparationofat

least 3mm must be supplied in the ﬁxed wiring�

• Togainaccesstothemainsconnectionterminals,remove

the rear access cover by unscrewing the 2 screws�

• Ifthesupplycordisdamaged,itmustbereplacedby

the manufacturer, its service agent or similarly qualiﬁed

persons in order to avoid a hazard�

• Forappliancesttedwithasupplyexiblecord,ifthe

cord is damaged, it must be replaced by the manufacturer

or its service agent or similarly qualiﬁed person in order

to avoid a hazard� The plug must be accessible after

installation�

Multi-phase

Where connection is made to a multi-phase 220-240V

supply, the bridge piece should be removed from between

the active connections�

User Manual - Page 17