User Manual Maytag MVWB965HW 6 cu. ft. 30 Inch Top Load Washer

Maytag MVWB965HW 6 cu. ft. 30 Inch Top Load Washer - Use Manual - Use Guide PDF.
Documents: Go to download!
User Manual

• User Manual - (English, French)

Dimension Guide

• Dimension Guide - (English)

Warranty

• Warranty - (English)

Installation Instruction

• Installation Instruction - (English)

Energy Guide

• Energy Guide - (English)

Table of contents

• CONTROL PANEL AND FEATURES
• CYCLE GUIDE
• USING YOUR WASHER
• WASHER MAINTENANCE
• TROUBLESHOOTING

Owner Guide Washer

CONTROL PANEL AND FEATURES

Not all features and cycles are available on all models.

NOTE: The control panel features a sensitive surface that responds to a light touch of your finger. To ensure your selections are registered, touch the control panel with your finger tip, not your fingernail. When selecting a setting or option, simply touch its name until the desired section is illuminated.

1. POWER BUTTON
   Touch to turn the washer On. Touching once while the washer is on will cancel the current cycle and turn the washer Off.
2. WASH CYCLE KNOB
   Use the Wash Cycle knob to select cycles on your washer. See the “Cycle Guide” for detailed descriptions of cycles.
3. START/PAUSE BUTTON
   Touch and hold the START/PAUSE button to begin the selected cycle; touch again to pause a cycle.
4. ESTIMATED CYCLE TIME
   The Estimated Cycle Time display shows the time required for the cycle to complete. Factors such as load size and water pressure may affect the time shown in the display. Tightly packed loads, unbalanced loads, or excessive suds may cause the washer to adjust the cycle time, as well.
   If you have set a delay start to the cycle, the Estimated Cycle Time display will show the delay time adjusted.
   
   See other models: REFRIGERATOR REFRIGERATOR MRT118FFFE M1202 M1200
   When the cycle is complete, the display will show END until the lid is opened.
5. CYCLE MODIFIERS
   When you select a cycle, its default settings or the previous cycle selection used will light up.
   DELAY START
   Touch DELAY START to delay the start of the wash cycle up to 12 hours (“12h”). Touch DELAY START until “0h” appears in the status display to turn off, or touch POWER.
   TEMPERATURE
   Temperature control senses and maintains uniform water temperatures by regulating incoming hot and cold water.
   Select a wash temperature based on the type of fabric and soils being washed. For best results and following the garment label instructions, use the warmest wash water that is safe for your fabric.
   On some cycles, warm and hot water may be cooler than your previous washer.
   Even for cold wash settings, some warm water may be added to the washer to maintain a minimum temperature.
   SOIL LEVEL
   Soil Level (wash time) is preset for each wash cycle.
   As you touch the Soil Level pad, the cycle time (minutes) will increase or decrease in the Estimated Time Remaining display and a different wash time will appear.
   Select the most suitable setting for your load. For heavily soiled items, select Heavy for more wash time. For lightly soiled items, select Light for less wash time. A lighter soil level setting will help reduce tangling and wrinkling.
   SPIN SPEED
   This washer automatically selects the spin speed based on the cycle selected. The preset speeds can be changed. Not all spin speeds are available with all cycles.
   Faster spin speeds mean shorter dry times, but may increase wrinkling in your load.
   Slower spin speeds mean less wrinkling, but will leave your load more damp.
   AUDIO LEVEL
   Use this to turn the button sounds and/or signal indicating the end of a wash cycle to medium, high, or off.
   NOTE: You may also turn off the tones that sound when a feature, setting, or option is touched.
6. OPTIONS
   You may add or remove options for each cycle. Not all options can be used with all cycles, and some are preset to work with certain cycles.
   MY CYCLE
   If you have a cycle with custom settings that you use frequently, you can use the My Cycle feature to keep your preferred settings ready to use. To save the cycle, touch and hold MY CYCLE (approximately 3 seconds) until a beep sounds and the My Cycle LED is lit. Once a configuration has been saved, you may power on the washer and briefly touch MY CYCLE to load your saved cycle and settings.
   FABRIC SOFTENER
   Select the Fabric Softener option so that the desired product is added to the load at the correct time.
   OXI
   Select the Oxi option so that the desired product is added to the load at the correct time.
   EXTRA RINSE
   This option can be used to automatically add a second rinse to most cycles.
   DEEP CLEAN + STEAM
   The Deep Clean + Steam option adds additional soak and wash time to many cycles to help remove tough stains, as well as a steam boost for added cleaning power. Deep Clean + Steam uses a heater within the washer to maintain the selected temperature setting throughout the wash period. Deep Clean + Steam may be selected as an option with other cycles.
   NOTE: The Deep Clean + Steam option may increase the selected temperature.
   DEEP FILL
   If you would like to add the maximum amount of water to your wash cycle, select the Deep Fill option.
   NOTES:
   Expect longer cycle times due to extended fill times when using the Deep Fill option.
   Deep Fill is not available in the Normal cycle mode.
7. CYCLE STATUS LIGHTS
   The Cycle Status Lights show the progress of a cycle. At each stage of the process, you may notice sounds or pauses that are different from traditional washers.
   DELAY
   When Delay Start has been selected, the Delay light will illuminate and remain illuminated until the cycle begins.
   LID LOCKED
   To allow for proper load sensing and spinning, the lid will lock and the Lid Locked light will turn on. This light indicates that the lid is locked and cannot be opened.
   If you need to open the lid, touch START/PAUSE. The lid will unlock once the washer movement has stopped. This may take several minutes if the load was spinning at a high speed. Touch and hold the START/PAUSE button again for up to 3 seconds to restart the cycle.
   Avoid opening the lid during sensing. The sensing process will start over when the washer is restarted.
   SENSING
   When the Start/Pause button is touched and held, the washer will first perform a self-test on the lid lock mechanism. You will hear a click, the basket will make a slight turn, and the lid will unlock briefly before locking again.
   Once the lid has locked the second time, the washer will use short, slow spins to estimate the load size. These sensing spins may take 2 to 3 minutes before water is added to the load and you may hear the hum of these spins. If the sensing light is on, then the washer is working properly. You will hear the motor turn the basket in short pulses to thoroughly wet the load. The washer will then move the load briefly, pause to allow water to soak into the load, and resume adding water.
   This process may repeat until the correct amount of water has been added for the load. You may also hear water flowing through the dispenser, adding detergent to the load.
   NOTE: Avoid opening the lid during sensing. The sensing process will start over when the washer is restarted. The sensing light may also come on during the Wash portion of the cycle. This is normal.
   WASH
   You will hear the motor and agitator moving the load. Unlike traditional washers, the load is not covered with water. Rather than diluting detergent as done in an agitator-style washer, this washer delivers the detergent directly to the soils. The motor sounds may change at different stages in the cycle. The wash time is determined by the selected Soil Level.
   RINSE
   You will hear sounds similar to the wash cycle as the washer rinses and moves the load.
   SPIN
   The washer spins the load at increasing speeds for proper water removal based on the selected cycle and spin speed.
   DONE
   Once the cycle is complete, this light will come on. Remove the load promptly for best results.

Dispensers

A. Detergent dispenser

Pour measured amount of liquid HE detergent into the detergent dispenser. The detergent will dispense at the optimum time during the wash cycle.

Use only High Efficiency (HE) liquid detergent.

NOTE: Do not place single-dose laundry packets or powder detergent into the dispenser. Add single-dose laundry packets or powder detergent directly to the washer basket.

B. Liquid fabric softener dispenser

Pour measured liquid fabric softener into the liquid fabric softener dispenser, if desired. It will dispense automatically at the optimum time.

• Use only liquid fabric softener in this dispenser.

C. Liquid chlorine bleach and Oxi dispenser

The bleach will be automatically diluted and dispensed at the optimum time during the wash cycle. This dispenser cannot dilute powdered bleach.

NOTE: If a gel bleach is used, the Oxi button must be touched to assist in dispensing the gel.

This dispenser holds up to 3/4 cup (180 mL) Oxi booster or other laundry booster, such as powdered or liquid color-safe bleach. Laundry boosters are automatically dispensed at the proper time during the wash cycle.

Be sure to select Oxi from the options to ensure proper dispensing.

NOTE: Fill dispenser with only Oxi. Do not mix with bleach.

IMPORTANT: Even on cold cycles, using the Oxi booster option will cause the washer to use some warm water to assist in dispensing the Oxi liquid/powder.

CYCLE GUIDE

For best fabric care, choose the cycle that best fits the load being washed. Recommended settings for best performance are shown in Bold. Not all settings and options are available on each cycle.

*Extended hot water cycle intended to help sanitize items such as sheets and towels. This cycle is not recommended for all fabrics. For best results, this cycle should be run to completion to ensure sanitation and should not be interrupted.

†Efficient use of resources, such as energy and water.

USING YOUR WASHER

Warning - Fire Hazard

• Never place items in the washer that are dampened with gasoline or other flammable fluids.
• No washer can completely remove oil.
• Do not dry anything that has ever had any type of oil on it (including cooking oils).
• Doing so can result in death, explosion, or fire.

Warning - Electronic Shock Hazard

• Plug into a grounded 3 prong outlet.
• Do not remove ground prong.
• Do not use an adapter.
• Do not use an extension cord.
• Failure to follow these instruction can result in death, fire, or electrical shock.

1. Sort and prepare your laundry

• Empty pockets. Loose change, buttons, or any small object can pass under the washplate and become trapped, causing unexpected sounds.
• Sort items by recommended cycle, water temperature, and colorfastness.
• Separate heavily soiled items from lightly soiled.
• Separate delicate items from sturdy fabrics.
• Do not dry items if stains remain after washing; heat can set stains into fabric.
• Treat stains promptly.
• Close zippers, fasten hooks, tie strings and sashes.
  Remove non-washable trim and ornaments.
• Mend rips and tears to avoid further damage to items during washing.

Helpful Tips:

• For best performance, use HE liquid detergent when washing bulky items.
• When washing waterproof or water-resistant items, load evenly.
• Use mesh bags to help avoid tangling when washing delicate or small items.
• Turn knits inside out to avoid pilling. Separate lint-takers from lint-givers. Synthetics, knits, and corduroy fabrics will pick up lint from towels, rugs, and chenille fabrics.
• Wash large, absorbent items with other water absorbent items or alone. Do not mix water absorbent items with items that do not absorb water as this can cause imbalance.

NOTE: Always read and follow fabric care labels instructions to avoid damage to your items.

2. Add laundry products

Single-dose laundry packets, powder detergent, or fabric softener crystals can be added to the basket prior to adding laundry.

NOTE: Always follow manufacturer’s instructions, and never add single-dose laundry packets, powder detergent, or fabric softener crystals to the dispensers. They will not dispense correctly. Add to the basket prior to adding laundry.

3. Load laundry into washer

For best performance, load items in loose heaps evenly around the agitator. Try mixing different sized items to reduce tangling.

IMPORTANT: Items need to move freely for best cleaning and to reduce wrinkling and tangling.

4. Add HE liquid detergent

Pour a measured amount of HE detergent into dispenser; always follow manufacturer’s directions for correct amount of detergent based on your load size.

5. Add liquid chlorine bleach or Oxi to dispenser (if desired)

Do not overfill, dilute, or use more than 1 cup (236 mL) of liquid cholorine bleach. Pour a measured amount of Oxi-type boosters, into dispenser; always follow manufacturer’s directions for correct amount of Oxi-based boosters based on your load size. Oxi is added during main wash.

IMPORTANT: Do not use color-safe bleach or Oxi products in the same cycle with liquid chlorine bleach. Oxi option must be selected to ensure proper distribution at correct time in cycle.

6. Add liquid fabric softener to dispenser (if desired)

Pour a measured amount of liquid fabric softener into dispenser; always follow manufacturer’s directions for correct amount of fabric softener based on your load size. Fabric Softener is added during rinse.

IMPORTANT: Do not overfill or dilute. Overfilling dispenser will cause fabric softener to immediately dispense into washer. Do not put fabric softener crystals into dispenser.

If Extra Rinse option is selected, fabric softener will be dispensed into the last rinse. It is normal for a small amount of water to remain in the dispenser at the end of a cycle.

7. Touch POWER to turn on washer

Close the lid and touch POWER to turn on the washer.

8. Select cycle

Turn the cycle knob to choose your wash cycle. For more information, see the “Cycle Guide.”

Estimated Time Remaining will light up with a cycle time. You may notice time adjusting during the cycle. This is normal.

If you do not want to begin a cycle immediately, you may choose Delay Start option.

To choose a delay time:

1. Touch DELAY START button to select desired delay time.
   Time will increase in hour increments up to 12 hours.
2. Touch and hold the START/PAUSE button to start delay start time.

IMPORTANT: When delaying a cycle, use liquid HE detergent only in the dispenser. Powdered detergents may absorb moisture from a previous cycle and clump before the wash cycle begins.

To cancel Delay Start:

1. Touch POWER to cancel Delay Start.

To pause Delay Start:

1. Touch the START/PAUSE button to pause Delay Start.
2. Touch and hold the START/PAUSE button again to start Delay Start time.

9. Select cycle modifiers

Once you select a cycle, the default modifiers or the previous set modifiers for that cycle will be lit. Touch the cycle settings buttons to change the Temperature, Soil Level, and Spin Speed, if desired. Not all settings are available with all cycles.

NOTE: Always read and follow fabric care labels instructions to avoid damage to your items. If not sure which temperature to use, refer to the chart below or select a cooler temperature.

Temperature suggestions

NOTE: Even for cold wash settings, some warm water may be added to the washer to maintain a minimum temperature.

10. Select cycle options

Select any other cycle options you may wish to add, if not previously set. Some cycles will automatically add certain options such as Extra Rinse. These may be turned off, if desired.

NOTE: Not all options are available with all cycles. Touch control panel to select any other options.

11. Touch and hold START/PAUSE button to begin wash cycle

Touch and hold the START/PAUSE button to start the wash cycle. When the cycle has finished, the end of cycle signal will sound (if set). Promptly remove items when cycle is done to avoid odor, reduce wrinkling, and rusting of metal hooks, zippers, and snaps.

Unlocking the lid to add items If you need to open the lid to add one or two missed items:

Touch START/PAUSE button to pause washer; the lid will unlock once the washer movement has stopped. This may take several minutes if the load was spinning at a high speed. Then close the lid and touch and hold the START/PAUSE button again to restart the cycle.

IMPORTANT: If lid is left open for more than 10 minutes, the water will pump out and the F8E6 error code will appear on the display.

WASHER MAINTENANCE

WATER INLET HOSES

Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Periodically inspect and replace inlet hoses if bulges, kinks, cuts, wear, or leaks are found.

When replacing your inlet hoses, mark the date of replacement on the label with a permanent marker.

NOTE: This washer does not include inlet hoses. See the Installation Instructions for more information.

WASHER CARE

Recommendations to Help Keep Your Washer Clean and Performing at its Best

1. Always use High Efficiency (HE) detergents and follow the HE detergent manufacturer’s instructions regarding the amount of HE detergent to use. Never use more than the recommended amount because that may increase the rate at which detergent and soil residue accumulate inside your washer, which in turn may result in undesirable odor.
2. Use warm and hot wash water settings sometimes (not exclusively cold water washes), because they do a better job of controlling the rate at which soils and detergent accumulate.
3. Always leave the washer lid open between uses to help dry out the washer and prevent the buildup of odor-causing residue.

Cleaning Your Top Loading Washer

Read these instructions completely before beginning the routine cleaning processes recommended below.

This Washer Maintenance Procedure should be performed, at a minimum, once per month or every 30 wash cycles, whichever occurs sooner, to control the rate at which soils and detergent may otherwise accumulate in your washer.

Cleaning the Inside of the Washer
To keep your washer odor-free, follow the usage instructions provided above, and use this recommended monthly cleaning procedure:

Clean Washer Cycle
This washer has a special cycle that uses higher water volumes in combination with affresh ® Washer Cleaner or liquid chlorine bleach to clean the inside of the washer.

Begin procedure

1. affresh ® Washer Cleaner Cycle Procedure (Recommended for Best Performance):
   a. Open the washer lid and remove any clothing or items.
   b. Place an affresh ® Washer Cleaner tablet in the bottom of the washer basket.
   c. Do not place an affresh ® Washer Cleaner tablet in the detergent dispenser.
   d. Do not add any detergent or other chemical to the washer when following this procedure.
   e. Close the washer lid.
   f. Touch POWER to turn on the washer.
   g. Select the Clean Washer cycle.
   h. Touch and hold the START/PAUSE button to begin the cycle. The Clean Washer Cycle Operation is described below.
   NOTE: For best results, do not interrupt cycle. If cycle must be interrupted, touch POWER. After the Clean Washer cycle has stopped, run a Rinse & Spin cycle to rinse cleaner from washer.
2. Chlorine Bleach Procedure (Alternative):
   a. Open the washer lid and remove any clothing or items.
   b. Add 1 cup (236 mL) of liquid chlorine bleach to the bleach compartment.
   NOTE: Use of more liquid chlorine bleach than is recommended above could cause washer damage over time.
   c. Close the washer lid.
   d. Do not add any detergent or other chemical to the washer when following this procedure.
   e. Touch POWER to turn on the washer.
   f. Select the Clean Washer cycle.
   g. Touch and hold the START/PAUSE button to begin the cycle. The Clean Washer Cycle Operation is described below.

NOTE: For best results, do not interrupt cycle. If cycle must be interrupted, touch POWER. After the Clean Washer cycle has stopped, run a Rinse & Spin cycle to rinse cleaner from washer.

Description of Clean Washer Cycle Operation:

1. This cycle will fill to a water level higher than in normal wash cycles to provide rinsing at a level above the water line for normal wash cycle.
2. During this cycle, there will be some agitation and spinning to increase the removal of soils.

After this cycle is complete, leave the lid open to allow for better ventilation and drying of the washer interior.

Cleaning the Outside of the Washer
Use an affresh ® Machine Cleaning Wipe or a soft, damp cloth or sponge to wipe away any spills. Use only mild soaps or cleaners when cleaning external washer surfaces.

IMPORTANT: To avoid damaging the washer’s finish, do not use abrasive products.

NON-USE AND VACATION CARE

Operate your washer only when you are home.
If moving, or not using your washer for a period of time, follow these steps:

1. Unplug or disconnect power to washer.
2. Turn off water supply to washer, to avoid flooding due to water pressure surge.

WINTER STORAGE CARE

IMPORTANT: To avoid damage, install and store washer where it will not freeze. Because some water may stay in hoses, freezing can damage washer. If storing or moving during freezing weather, winterize your washer.

To winterize washer:

1. Shut off both water faucets; disconnect and drain water inlet hoses.
2. Put 1 qt. (1 L) of R.V.-type antifreeze in basket and run washer on Rinse & Spin cycle for about 30 seconds to mix antifreeze and remaining water.
3. Unplug washer or disconnect power.

TRANSPORTING YOUR WASHER

1. Shut off both water faucets. Disconnect and drain water inlet hoses.
2. If washer will be moved during freezing weather, follow “Winter Storage Care” directions before moving.
3. Disconnect drain from drain system.
4. Unplug power cord.
5. Place inlet hoses inside washer basket.
6. Drape power cord and drain hose over the console and secure with masking tape.
7. Place foam packing ring from original shipping materials back inside washer. If you do not have packing ring, place heavy blankets or towels into basket opening. Close lid and place tape over lid and down front of washer. Keep lid taped until washer is placed in new location. Transport washer in the upright position.

Warning - Electronic Shock Hazard

• Plug into a grounded 3 prong outlet.
• Do not remove ground prong.
• Do not use an adapter.
• Do not use an extension cord.
• Failure to follow these instruction can result in death, fire, or electrical shock.

REINSTALLING/USING WASHER AGAIN

To reinstall washer after non-use, vacation, winter storage or moving:

1. Refer to Installation Instructions to locate, level, and connect washer.
2. Before using again, run washer through the following recommended procedure:

To use washer again:

1. Flush water pipes and hoses. Reconnect water inlet hoses. Turn on both water faucets.
2. Plug in washer or reconnect power.
3. Run washer through PowerWash ® cycle to clean washer and remove antifreeze, if used. Use only HE High Efficiency detergent. Use half the manufacturer’s recommended amount for a medium-size load.

TROUBLESHOOTING