Loading ...
Loading ...
Loading ...
7
Sanitizes dishes and glassware in accordance with
NSF International NSF/ANSI Standard 184 for
Residential Dishwashers. Certified residential
dishwashers are not intended for licensed food
establishments. Only sanitizing cycles have been
designed to meet the requirements of the NSF/ANSI
184 performance standard for soil removal and for
sanitization efficacy. There is no intention, either
directly or indirectly, that all cycles on a NSF/ANSI
184 certified dishwasher meet the NSF/ANSI 184
performance standard for soil removal and for
sanitization efficacy.
At end of the cycle, the sanitized indicator or word
“sanitized”, on some models, will glow. If your load
did not properly sanitize, the indicator will flash at the
end of the cycle. This can happen if the cycle is
interrupted, or if the water does not reach the
required temperature. The light goes off when you
open and close the door or press CANCEL.
Auto
PowerBlast™
Normal
Increased main
wash temperature
from 105°F (41°C)
to 145°F (63°C)
and final rinse from
140°F (60°C) to
156°F (69°C).
:04 to 1:15 0-3.0
(0-11.2)
Dries dishes with heat and the fan (on some cycles).
Use this option with rinse aid. Plastic items are less
likely to deform when loaded in top rack. Turn option
off for an air dry.
NOTE: The fan may run for 1 hour after the cycle
ends for some cycle/option selections. The fan can
be stopped by opening the door or pressing any key
on the console.
Auto
PowerBlast™
Normal
Quick
Uses heating
element and the
fan (with some
cycles) to speed
drying times.
:12 to :46 0
Dries dishes with heat and the fan (on some cycles).
Use this option, with rinse aid, to get the best drying
results. Plastic items are less likely to deform when
loaded in top rack.
NOTE: The fan may run for 1 hour after the cycle
ends for some cycle/option selections. The fan can
be stopped by opening the door or pressing any key
on the console.
Auto
PowerBlast™
Normal
Quick
Uses heating
element and the
fan (with some
cycles) to speed
drying times.
1:01 to 1:17 0
CONTROL PURPOSE COMMENTS
Press to start or resume a
wash cycle
If the door is opened during a cycle or power is interrupted, Start/Resume indicator
flashes. Cycle will not resume until door is closed and Start/Resume is pressed.
NOTE: If Start/Resume button is located on top of door, push door firmly closed
within 4 seconds of pressing Start/Resume. If door is not closed within 4 seconds,
start button light will flash, an audible tone will be heard (on some top control models),
and cycle will not start.
Cancels wash cycle. Press and hold CANCEL/DRAIN for 3 seconds to cancel the wash cycle. The
dishwasher starts a 3-minute drain (if needed). Let dishwasher drain completely.
Use Control Lock to avoid
unintended use of
dishwasher between cycles,
or cycle and option changes
during a cycle.
To turn on Lock, press and hold SANITIZE for 3 seconds. Control Lock light will stay
on for a short time, indicating that it is activated and all buttons are disabled. If you
press any button while the dishwasher is locked, light flashes 3 times. Dishwasher
door can still be opened/closed while controls are locked.
To turn off Lock, press and hold SANITIZE for 3 seconds. Light turns off.
NOTE: If the model requires you to press and hold Sanitize to lock controls, Control
Locked LED(C) will be on or off to indicate whether Control Lock is active or not.
OPTIONS CAN BE
SELECTED
WITH
WHAT IT DOES ADDED TIME
TO CYCLE
ADDED
WATER
GALLONS
(LITERS)
AB
C
Loading ...
Loading ...
Loading ...