Loading ...
Loading ...
PLAY/PAUSE BUTTON: This button has multiple functions – a visual indicator of network connectivity and a PLAY/
PAUSE button. For a full listing of LED Blink Codes, please see #1 – Blink Codes. For an ungrouped Player, press
the button to Play and Pause the stream. If listening to an Internet radio stream, the Pause function will work for 30
seconds. At this point, the buffer is full and the stream will Stop. When a Player is grouped, pressing the PLAY/PAUSE
button will Mute that Player while other Players continue the stream. The Player’s LED will flash blue when muted.
+, - (VOLUME): Toggle either button to vary volume level. Volume level will not change if you press and hold either
button.
(+): Increase volume level
(-): Decrease volume level
PREVIOUS TRACK/NEXT TRACK: These buttons can be used to go back to the previous track◄◄ or skip to the
next track►► in your current playlist.
AUDIO OUT: Connect to the corresponding analog audio input of an amplifier, receiver or stereo system.
SUBW (SUBWOOFER) OUT: A Subwoofer can also be connected directly to the VAULT 2i. Connect SUBW OUT to a
powered (“active”) subwoofer.
COAX OUT: Using a coax cable (not provided), connect one end to the COAX OUT of the VAULT 2i and the other end to
the corresponding coax input of compatible devices such as receivers, computer soundcards or other digital processors.
OPTICAL OUT: Using a Digital Optical cable (not provided), connect one end to the OPTICAL OUT of the VAULT 2i and
the other end to the corresponding digital audio input of compatible devices such as receivers, computer soundcards or
other digital processors.
OPTICAL IN/ANALOG IN: Using a 3.5mm Stereo Audio Cable (provided), connect one end to the Analog In of the
VAULT 2i and the other end to the corresponding analog output of other compatible devices. The source will show as an
Analog Input in the Navigation Drawer of the Bluesound app. Using the 3.5mm Mini Jack to Toslink adaptor (included
with the VAULT 2i), a digital optical source can also be added. This will appear as Optical Input in the Navigation Drawer.
TRIGGER OUT : A 12V DC signal is available using TRIGGER OUT. The 12V DC signal can be used to control or activate
other external devices equipped with a corresponding 12V trigger input using a 3.5mm mono audio cable.
IR IN : An infrared extender can be connected to allow for programmable learning remotes to control volume and source
selection when a VAULT 2i is stored in a way that the front panel IR sensor is not visible.
USB (TYPE A): Connect a USB mass storage device or Bluetooth adaptor to the USB input. Typical USB mass
storage devices compatible with the VAULT 2i include portable flash memory devices and external hard drives (FAT32
formatted).
LAN PORT: To setup the VAULT 2i, a LAN port for a wired ethernet connection is required. Using the Ethernet cable
provided, connect one end of the Ethernet cable to the LAN port of your wired Ethernet broadband router and the other
end to the VAULT 2i’s LAN port.
SERVICE: Use the SERVICE port in conjunction with USB (Type B Mini) to initially load firmware on the Player. This is
not for consumer use. Only Authorized Bluesound Service personnel can access this USB port and SERVICE control
button.
AC MAINS INPUT: The VAULT 2i comes supplied with two separate AC power cords. Select the AC power cord
appropriate for your region. Before connecting the plug to the wall outlet, connect firmly the other end of the AC power
cord to VAULT 2i’s AC Mains input socket. Never force the plug into a wall outlet. An adaptor may be necessary in
certain regions. Always disconnect the plug from the wall outlet first, before disconnecting the cable from the VAULT 2i’s
AC Mains input socket.
FRONT PANEL HEADPHONE JACK: A 3.5mm headphone jack is located on the front of the VAULT 2i.
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Loading ...