Operation Manual
Embroidery Machine
Product Code: 882-D80/D82
Be sure to read this document before using the machine.
We recommend that you keep this document nearby for future reference.
TRADEMARKS
IMPORTANT:
READ BEFORE DOWNLOADING, COPYING, INSTALLING OR USING.
By downloading, copying, installing or using the software you agree to this license. If you do not agree
to this license, do not download, install, copy or use the software.
Intel License Agreement For Open Source Computer Vision Library
Copyright © 2000, Intel Corporation, all rights reserved. Third party copyrights are property of their respective owners.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the
following conditions are met:
• Redistribution’s of source code must retain the above copyright notice, this list of conditions and the following
disclaimer.
• Redistribution’s in binary form must reproduce the above copyright notice, this list of conditions and the
following disclaimer in the documentation and/or other materials provided with the distribution.
• The name of Intel Corporation may not be used to endorse or promote products derived from this software
without specific prior written permission.
This software is provided by the copyright holders and contributors “as is” and any express or implied warranties,
including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose are
disclaimed. In no event shall Intel or contributors be liable for any direct, indirect, incidental, special, exemplary,
or consequential damages (including, but not limited to, procurement of substitute goods or services; loss of use,
data, or profits; or business interruption) however caused and on any theory of liability, whether in contract, strict
liability, or tort (including negligence or otherwise) arising in any way out of the use of this software, even if
advised of the possibility of such damage.
All information provided related to future Intel products and plans is preliminary and subject to change at any time, without notice.
SD is a registered trademark or a trademark of SD-3C, LLC.
CompactFlash is a registered trademark or a trademark of Sandisk Corporation.
Memory Stick is a registered trademark or a trademark of Sony Corporation.
SmartMedia is a registered trademark or a trademark of Toshiba Corporation.
MultiMediaCard (MMC) is a registered trademark or a trademark of Infineon Technologies AG.
xD-Picture Card is a registered trademark or a trademark of Fuji Photo Film Co. Ltd.
IBM is a registered trademark or a trademark of International Business Machines Corporation.
Microsoft, Windows and Windows Vista are registered trademarks or trademarks of Microsoft Corporation.
Each company whose software title is mentioned in this manual has a Software License Agreement specific to its proprietary programs.
All other brands and product names mentioned in this manual are registered trademarks of their respective companies. However, the
explanations for markings such as
® and ™ are not clearly described within the text.
INTRODUCTION
B-1
Thank you for purchasing this machine. Before using this machine, carefully read the “IMPORTANT
SAFETY INSTRUCTIONS”, and then study this manual for the correct operation of the various functions.
In addition, after you have finished reading this manual, store it where it can quickly be accessed for
future reference.
Please read these safety instructions before attempting to use the machine.
DANGER - To reduce the risk of electrical shock
1Always unplug the machine from the electrical outlet immediately after using, when cleaning, making any user
servicing adjustments mentioned in this manual, or if you are leaving the machine unattended.
WARNING - To reduce the risk of burns, fire, electrical shock, or injury to
persons.
2Always unplug the machine from the electrical outlet when making any adjustments mentioned in the instruction
manual.
• To unplug the machine, switch the machine to the symbol “O” position to turn it off, then grasp the plug and pull
it out of the electrical outlet. Do not pull on the cord.
• Plug the machine directly into the electrical outlet. Do not use an extension cord.
• Always unplug your machine if the power is cut.
3Electrical Hazards:
• This machine should be connected to an AC power source within the range indicated on the rating label. Do not
connect it to a DC power source or inverter. If you are not sure what kind of power source you have, contact a
qualified electrician.
• This machine is approved for use in the country of purchase only.
4Never operate this machine if it has a damaged cord or plug, if it is not working properly, has been dropped or
damaged, or water is spilled on the unit. Return the machine to the nearest authorized dealer for examination,
repair, electrical or mechanical adjustment.
• While the machine is stored or in use if you notice anything unusual, such as an odor, heat, discoloration or
deformation, stop using the machine immediately and unplug the power cord.
• When transporting the machine, be sure to carry it by its handle. Lifting the machine by any other part may
damage the machine or result in the machine falling, which could cause injuries.
• When lifting the machine, be careful not to make any sudden or careless movements, otherwise you may injure
your back or knees.
INTRODUCTION
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
B-2
5Always keep your work area clear:
• Never operate the machine with any air openings blocked. Keep ventilation openings of the machine and foot
control free from the build up of lint, dust, and loose cloth.
• Do not use extension cords. Plug the machine directly into the electrical outlet.
• Never drop or insert foreign objects in any opening.
• Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
• Do not use the machine near a heat source, such as a stove or iron; otherwise, the machine, power cord or
garment being sewn may ignite, resulting in fire or an electric shock.
• Do not place this machine on an unstable surface, such as an unsteady or slanted table, otherwise the machine
may fall, resulting in injuries.
6Special care is required when embroidering:
• Always pay close attention to the needle. Do not use bent or damaged needles.
• Keep fingers away from all moving parts. Special care is required around the machine needle.
• Switch the machine to the symbol “O” position to turn it off when making any adjustments in the needle area.
• Do not use a damaged or incorrect needle plate, as it could cause the needle to break.
• Do not push or pull the fabric when embroidering.
7This machine is not a toy:
• Your close attention is necessary when the machine is used by or near children.
• The plastic bag that this machine was supplied in should be kept out of the reach of children or disposed of.
Never allow children to play with the bag due to the danger of suffocation.
• Do not use outdoors.
8For a longer service life:
• When storing this machine, avoid direct sunlight and high humidity locations. Do not use or store the machine
near a space heater, iron, halogen lamp, or other hot objects.
• Use only neutral soaps or detergents to clean the case. Benzene, thinner, and scouring powders can damage the
case and machine, and should never be used.
• Always consult the operation manual when replacing or installing any assemblies, the presser feet, needle, or
other parts to assure correct installation.
9For repair or adjustment:
• If the light unit is damaged, it must be replaced by an authorized dealer.
• In the event a malfunction occurs or adjustment is required, first follow the troubleshooting table in the back of
the operation manual to inspect and adjust the machine yourself. If the problem persists, please consult your
local authorized Brother dealer.
Use this machine only for its intended use as described in the manual.
Use accessories recommended by the manufacturer as contained in this manual.
Use only the interface cable (USB cable) included with this machine.
Use only the sensor pen included with this machine.
Use only the mouse designed specifically for this machine.
The contents of this manual and specifications of this product are subject to change without notice.
For additional product information and updates, visit our website at www.brother.com
IMPORTANT SAFETY INSTRUCTIONS
B-3
SAVE THESE INSTRUCTIONS
This machine is intended for household use.
FOR USERS IN COUNTRIES EXCEPT CENELEC COUNTRIES
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety. Children should be supervised
to ensure that they do not play with the appliance.
FOR USERS IN CENELEC COUNTRIES
This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved. Children shall not
play with the appliance. Cleaning and user maintenance shall not be made by
children without supervision.
FOR USERS IN THE UK, EIRE, MALTA
AND CYPRUS ONLY
IMPORTANT
• In the event of replacing the plug fuse, use a fuse approved by ASTA to BS 1362, i.e. carrying the mark,
rating as marked on plug.
• Always replace the fuse cover. Never use plugs with the fuse cover omitted.
• If the available electrical outlet is not suitable for the plug supplied with this equipment, you should contact your
authorized dealer to obtain the correct lead.
IMPORTANT SAFETY INSTRUCTIONS
B-4
Federal Communications Commission (FCC)
Declaration of Conformity (For USA Only)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• The included interface cable should be used in order to ensure compliance with the limits for a Class B digital
device.
• Changes or modifications not expressly approved by Brother Industries, Ltd. could void the user’s authority to
operate the equipment.
Responsible Party: Brother International Corporation
200 Crossing Boulevard
P.O. Box 6911
Bridgewater, NJ 08807-0911 USA
TEL : (908) 704-1700
declares that the product
Product Name:
Model Number:
Brother Sewing Machine
VE2200, BP2100, BP2150L
WHAT YOU CAN DO WITH THIS MACHINE
B-5
WHAT YOU CAN DO WITH THIS MACHINE
B Basic operations
After purchasing your machine, be sure to read this section first. This section provides details on the
initial setup procedures as well as descriptions of this machine’s more useful functions.
Chapter 1 Getting Ready
To learn the operation of the principal parts and the
screens
Page B-16
Chapter 2 Sensor Functions (For
models equipped with the sensor
function)
Try the new function using the supplied sensor pen
Page B-52
E Embroidering
This section provides instruction to embroider designs with this machine.
Chapter 1, “Embroidery”, provides details on sewing embroidery patterns stored on the machine as well
as patterns that have been imported. Chapter 2, “Embroidery Edit”, provides details on editing
embroidery patterns to create custom embroidery.
Chapter 1 Embroidery
Maximum 30 cm × 18 cm (approx. 12 inches × 7 inches)
for large embroidery designs
Page E-2
Chapter 2 Embroidery Edit
Designs can be combined, rotated or enlarged
Page E-56
A Appendix
This section provides important information for operating this machine.
Chapter 1 How to Create Bobbin
Work
To learn how to create bobbin work
Page A-2
Chapter 2 Maintenance and
Troubleshooting
Find troubleshooting tips and pointers as well as how
to keep your machine in the best working condition.
Page A-14
CONTENTS
B-6
TRADEMARKS
INTRODUCTION................................................. 1
IMPORTANT SAFETY INSTRUCTIONS ................ 1
WHAT YOU CAN DO WITH THIS MACHINE ..... 5
NAMES OF MACHINE PARTS AND THEIR
FUNCTIONS.......................................................... 8
Machine................................................................................. 8
Needle and Presser Foot Section ............................................ 9
Embroidery Unit..................................................................... 9
Operation Buttons................................................................ 10
Included Accessories............................................................ 11
Options................................................................................ 13
B Basic operations
Chapter1 Getting Ready 16
TURNING THE MACHINE ON/OFF................... 17
Setting Your Machine for the First Time................................ 18
LCD SCREEN ...................................................... 20
Using the Machine Setting Mode Key .................................. 22
Using the Machine Help Key ............................................... 29
LOWER THREADING ......................................... 31
Winding the Bobbin ............................................................. 31
Setting the Bobbin ................................................................ 36
UPPER THREADING........................................... 38
Upper Threading .................................................................. 38
Using Threads that Unwind Quickly .................................... 41
CHANGING THE EMBROIDERY FOOT ............. 42
Removing the Embroidery Foot ............................................ 42
Attaching the Embroidery Foot ............................................. 42
CHANGING THE NEEDLE.................................. 45
About the Needle ................................................................. 46
BEFORE EMBROIDERING .................................. 46
Embroidery Step by Step....................................................... 46
About the Embroidery Unit................................................... 47
USING FUNCTIONS BY CONNECTING THE
ACCESSORY TO THE MACHINE ........................ 49
Using USB Media or Embroidery Card Reader/USB Card
Writer Module* .................................................................... 49
Connecting the Machine to the Computer ............................ 49
Using a USB Mouse ............................................................. 50
Chapter2
Sensor Functions (For models equipped
with the sensor function)
52
CONNECTING THE SENSOR PEN...................... 53
Using the Sensor Pen Holder................................................ 53
USING THE SENSOR PEN .................................. 55
Using the Sensor Pen............................................................ 55
Important Information about Sensor Pen............................... 55
Calibrating the Sensor Pen.................................................... 56
USING SENSOR FUNCTIONS IN
“EMBROIDERY”/“EMBROIDERY EDIT” MODE
... 58
Specifying the Embroidering Position With the Sensor Pen ... 58
E Embroidering
Chapter1 Embroidery 2
SELECTING PATTERNS......................................... 3
Selecting Embroidery Patterns/Brother “Exclusives”/Floral
Alphabet/Bobbin Work Patterns ............................................. 4
Selecting Character Patterns................................................... 5
Selecting Frame Patterns........................................................ 7
Selecting Patterns from Embroidery Cards.............................. 7
Selecting Patterns from USB Media/Computer ....................... 8
VIEWING THE EMBROIDERING SCREEN ........... 9
PREPARING THE FABRIC .................................. 11
Attaching Iron-on Stabilizers (Backing) to the Fabric ............ 11
Hooping the Fabric in the Embroidery Frame....................... 13
Embroidering Small Fabrics or Fabric Edges......................... 16
ATTACHING THE EMBROIDERY FRAME .......... 17
CONFIRMING THE PATTERN POSITION ......... 19
Checking the Pattern Position .............................................. 19
Previewing the Completed Pattern ....................................... 20
SEWING AN EMBROIDERY PATTERN............... 21
Embroidery Attractive Finishes............................................. 21
Sewing Embroidery Patterns................................................. 22
Sewing Embroidery Patterns Which Use Appliqué ............... 23
ADJUSTMENTS DURING THE EMBROIDERY
PROCESS ............................................................. 26
If the Bobbin Runs Out of Thread ........................................ 26
If the Thread Breaks During Sewing..................................... 27
Restarting from the Beginning.............................................. 28
Resuming Embroidery After Turning Off the Power.............. 28
MAKING EMBROIDERY ADJUSTMENTS........... 30
Adjusting Thread Tension .................................................... 30
Adjusting the Bobbin Case (with No Color on the Screw) .... 31
Using the Automatic Thread Cutting Function
(END COLOR TRIM)............................................................ 32
Using the Thread Trimming Function (JUMP STITCH TRIM)
... 32
Adjusting the Embroidery Speed .......................................... 33
Changing the Thread Color Display..................................... 34
Changing the “Embroidery Frame Display”.......................... 35
REVISING THE PATTERN................................... 36
Moving the Pattern .............................................................. 36
Aligning the Pattern and the Needle .................................... 36
Changing the Size of the Pattern .......................................... 37
Rotating the Pattern ............................................................. 38
Creating a Horizontal Mirror Image ..................................... 39
Enlarging the Editing Screen................................................. 39
Changing the Density (Alphabet Character and Frame
Patterns Only)...................................................................... 40
Changing the Colors of Alphabet Character Patterns............ 40
Embroidering Linked Characters .......................................... 41
Uninterrupted Embroidering (Monochrome - Using a Single
Color) .................................................................................. 43
USING THE MEMORY FUNCTION ................... 44
Embroidery Data Precautions............................................... 44
Saving Embroidery Patterns in the Machine’s Memory......... 45
Saving Embroidery Patterns to USB Media ........................... 46
Saving Embroidery Patterns in the Computer ....................... 47
Retrieving Patterns from the Machine’s Memory.................. 48
Recalling from USB Media................................................... 49
Recalling from the Computer............................................... 50
EMBROIDERY APPLICATIONS .......................... 51
Using a Frame Pattern to Make an Appliqué (1)................... 51
Using a Frame Pattern to Make an Appliqué (2)................... 52
Sewing Split Embroidery Patterns......................................... 53
Chapter2 Embroidery Edit 56
EXPLANATION OF FUNCTIONS....................... 57
SELECTING PATTERNS TO EDIT ....................... 58
Selecting Embroidery Patterns/Brother “Exclusives”/Floral
Alphabet Patterns/Frame/Bobbin Work Patterns ................... 59
Selecting Alphabet Character Patterns.................................. 59
EDITING PATTERNS .......................................... 61
Moving the Pattern .............................................................. 63
CONTENTS
CONTENTS
B-7
Rotating the Pattern.............................................................. 63
Changing the Size of the Pattern .......................................... 63
Deleting the Pattern ............................................................. 63
Displaying Patterns in the Screen Magnified by 200% ......... 63
Changing the Configuration of Character Patterns ................ 64
Changing Character Spacing ................................................ 64
Reducing Character Spacing ................................................ 65
Separating Combined Character Patterns ............................. 65
Changing the Color of Each Alphabet Character in a Pattern
... 66
Embroidering Linked Characters .......................................... 67
Changing the Thread Color .................................................. 67
Creating a Custom Thread Table .......................................... 68
Choosing a Color from the Custom Thread Table................. 71
Designing Repeated Patterns................................................ 72
Embroidering the Pattern Repeatedly ................................... 76
Duplicating a Pattern ........................................................... 78
After Editing ......................................................................... 79
COMBINING PATTERNS ................................... 80
Editing Combined Patterns ................................................... 80
Sewing Combined Patterns .................................................. 83
VARIOUS EMBROIDERING FUNCTIONS ......... 84
Uninterrupted Embroidering (Monochrome - Using a Single
Color) .................................................................................. 84
Basting Embroidery .............................................................. 84
USING THE MEMORY FUNCTION.................... 85
A Appendix
Chapter1 How to Create Bobbin Work 2
ABOUT BOBBIN WORK ...................................... 3
PREPARING FOR BOBBIN WORK ....................... 3
Required Materials................................................................. 3
Upper Threading.................................................................... 4
Preparing the Bobbin Thread ................................................. 4
CREATING BOBBIN WORK................................. 8
Selecting the Pattern .............................................................. 8
Start Embroidering ............................................................... 10
ADJUSTING THE THREAD TENSION ................ 12
TROUBLESHOOTING........................................ 13
Chapter2
Maintenance and Troubleshooting
14
CARE AND MAINTENANCE............................... 15
Restrictions on oiling ........................................................... 15
Precautions on storing the machine ..................................... 15
Cleaning the LCD Screen ..................................................... 15
Cleaning the Machine Casing .............................................. 15
Cleaning the Race ................................................................ 15
Cleaning the Cutter in the Bobbin Case Area ....................... 17
About the Maintenance Message ......................................... 17
ADJUSTING THE SCREEN.................................. 18
Adjusting the Brightness of the Screen Display..................... 18
Touch Panel is Malfunctioning............................................. 18
TROUBLESHOOTING........................................ 19
ERROR MESSAGES ............................................. 22
SPECIFICATIONS ............................................... 25
UPGRADING YOUR MACHINE’S SOFTWARE
... 26
Upgrade Procedure Using USB Media ................................. 26
Upgrade Procedure Using Computer ................................... 27
INDEX ................................................................ 28
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS
B-8
The names of the various parts of the machine and their functions are described below. Before using the
machine, carefully read these descriptions to learn the names of the machine parts.
Machine
■ Front View
a Top cover
Open the top cover to thread the machine and wind the
bobbin.
b Pre-tension disk
Pass the thread around the pre-tension disk when winding the
bobbin thread. (page B-31)
c Thread guide for bobbin winding
Pass the thread through this thread guide when winding the
bobbin thread. (page B-31)
d Spool pin
Place a spool of thread on the spool pin. (page B-38)
e Spool cap
Use the spool cap to hold the spool of thread in place.
(page B-38)
f Supplemental spool pin
Use this spool pin to wind the bobbin thread. (page B-31)
g Bobbin winder
Use the bobbin winder when winding the bobbin. (page B-31)
h LCD (liquid crystal display)
Settings for the selected pattern and error messages appear in
the LCD. (page B-20)
i Speaker
j Operation buttons (5 buttons)
Use these buttons to operate the machine. (page B-10)
k Embroidery unit
Attach the embroidery unit to embroider (page B-47).
l Thread cutter
Pass the threads through the thread cutter to cut them.
(page B-40)
m Thread guide plate
Pass the thread around the thread guide plate when threading
upper thread. (page B-38)
■ Right-side/Rear View
a Connector for the presser foot
Connect the embroidery foot “W+” with LED pointer. (The
embroidery foot “W+” with LED pointer is optional on certain
models.) (page B-42)
b Handle
Carry the machine by its handle when transporting the
machine.
c Presser foot lever
Raise and lower the presser foot lever to raise and lower the
presser foot. (page B-42)
d Air vent
The air vent allows the air surrounding the motor to circulate.
Do not cover the air vent while the machine is being used.
e Main power switch
Use the main power switch to turn the machine ON and OFF.
(page B-17)
f Power cord receptacle
Insert the power cord into the machine receptacle. (page B-17)
g Sensor pen holder connector (For models equipped
with the sensor function)
Connect the included sensor pen holder. (page B-53)
h Sensor pen jack (For models equipped with the
sensor function)
Connect the sensor pen. (page B-53)
i USB port for computer
In order to import/export patterns between a computer and the
machine, plug the USB cable into the USB port. (page B-49,
E-47)
j USB port for mouse / media (USB 2.0)
In order to send patterns from/to USB media, plug the USB
media directly into the USB port. (page B-49, E-46)
Connect the USB mouse to operate with mouse. (page B-50)
k Handwheel
Rotate the handwheel toward you (counterclockwise) to raise
and lower the needle. The wheel should be turned toward the
front of the machine.
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS
B-9
Needle and Presser Foot Section
a Embroidery foot screw
Use the embroidery foot screw to hold the embroidery foot in
place. (page B-42)
b Embroidery foot
The embroidery foot helps control fabric flexibility for better
stitch consistency. Use the embroidery foot “W+” with LED
pointer or embroidery foot “W” for most machine embroidering.
(page B-42)
c Bobbin cover
Open the bobbin cover to set the bobbin. (page B-36)
d Needle plate cover
Remove the needle plate cover to clean the race. (page E-22)
e Needle plate
f Needle bar thread guide
Pass the upper thread through the needle bar thread guide.
(page B-38)
g Needle clamp screw
Use the needle clamp screw to hold the needle in place.
(page B-45)
Embroidery Unit
a Carriage
The carriage moves the embroidery frame automatically when
embroidering. (page B-47)
b Release button (located under the embroidery unit)
Press the release button to remove the embroidery unit.
(page B-47)
c Embroidery frame holder
Insert the embroidery frame into the embroidery frame holder
to hold the frame in place. (page E-17)
d Frame-securing lever
Press the frame-securing lever down to secure the embroidery
frame. (page E-17)
e Embroidery unit connection
Insert the embroidery unit connection into the connection port
when attaching the embroidery unit. (page B-47)
CAUTION
• Before inserting or removing the embroidery
unit, turn the main power to OFF.
• After the embroidery frame is set in the frame
holder, be sure the frame-securing lever is
correctly lowered.
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS
B-10
Operation Buttons
a “Start/Stop” button
Press this button to begin embroidering. The button changes
color according to the machine’s operation mode.
b “Needle Position” button
Press this button to raise or lower the needle.
c “Thread Cutter” button
Press this button after embroidering to automatically trim the
excess thread.
d “Presser Foot Lifter” button
Press this button to lower the embroidery foot and apply
pressure to the fabric. Press this button again to raise the
embroidery foot.
e “Automatic Threading” button
Use this button to automatically thread the needle.
Green: The machine is ready to embroider or is
embroidering.
Red: The machine cannot embroider.
CAUTION
• Do not press the thread cutter button after the
threads have been cut. The needle may break
and threads may become tangled, or damage
to the machine may occur.
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS
B-11
Included Accessories
1* 2*
345678
91011
12
*
13 14 15 16
17
* 18
19 20 21 22
23*
24
25
* 26*
27 28
29
* 30*
31*
32 33 34 35
*Included accessories vary depending on the countries or regions.
75/11
3 needles
90/14
1 needle
75/11 2 needles:
Ball point needle
for embroidery
HAX130EBBR
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS
B-12
*1 75/11 3 needles
90/14 1 needle
*2 75/11 2 needles
Ball point needle for embroidery
HAX130EBBR
No. Part Name
Part Code
Americas Others
1 Embroidery foot “W+” with
LED pointer (on machine)
*
FLED1: XF4168-001 (EU area)
XF3124-001 (other area)
2 Embroidery foot “W” (on
machine)
*
XF4012-001
3
Needle set
*1
X59535-051
4
Ball point needle set
*2
XD0705-051
5 Bobbin × 10
(One is on machine.)
SA156 SFB:
XA5539-151
6 Seam ripper XF4967-001
7 Scissors XC1807-121
8 Cleaning brush X59476-051
9 Screwdriver (small) X55468-051
10 Screwdriver (large) XC4237-021
11 Disc-shaped screwdriver XC1074-051
12
Vertical spool pin
*
XC8619-052
13 Spool cap (small) 130013-154
14 Spool cap (medium) × 2
(One is on machine.)
X55260-153
15 Spool cap (large) 130012-054
16 Spool cap (special) XA5752-121
17
Bobbin clip × 10
*
XE3060-001
18 Spool felt (on machine) X57045-051
19
Spool net × 2
XA5523-050
20 Embroidery needle plate
cover
XE5131-001
21 Touch pen (stylus) XA9940-051
22 USB cable XD0745-051
23 Bobbin case (gray, for bobbin
work)
*
XE8298-001
24 Bobbin cover (on machine) XE8992-101
25 Embroidery frame set
(medium) H 10 cm × W 10 cm
(H 4 inches × W 4 inches)
*
SA438 EF74:
XC8480-152
26 Embroidery frame set (large)
H 18 cm × W 13 cm
(H 7 inches × W 5 inches)
*
SA439 EF75:
XC8481-152
27 Embroidery frame set
(extra large)
H 30 cm × W 18 cm
(H 12 inches × W 7 inches)
SA440 EF76:
XC8482-152
Embroidery frame set
(extra large)
H 30 cm × W 20 cm
(H 12 inches × W 8 inches)
SA447 EF92:
XE5071-001
28 Brother poly #90 bobbin
thread
EBT-PE EBT-PEN:
XC5996-001
29
Stabilizer material
*
SA519 BM3:
XE0806-001
30
Sensor pen
*
XF4992-001 (EU area)
XF3116-001 (other area)
31
Pen holder
*
XF2973-001
32 Dust cover XF4569-001
33 Accessory bag XC4487-021
34 Operation manual This manual
35 Quick Reference Guide XF3841-001 (882-D80)
XF3637-001 (882-D82)
Memo
• Always use accessories recommended for
this machine.
• Placing bobbin clips on bobbins helps
prevent the thread from unwinding from the
bobbin. In addition, snapping bobbin clips
together allows the bobbins to be
conveniently stored and prevents them from
rolling around if they are dropped.
• Included accessories may vary depending
on the country or region.
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS
B-13
Options
The following are available as optional accessories to be purchased separately from your authorized
Brother dealer.
123456
78910 11
No. Part Name
Part Code
Americas Others
1 Square embroidery frame
H 15 cm x W 15 cm (H 6
inches x W 6 inches)
SA448
(U.S.A.)
SA448C
(Canada)
SEF150:
XF4163-001
2 Embroidery foot “W+” with
LED pointer
FLED1: XF4168-001 (EU area)
XF3124-001 (other area)
3 Embroidery foot “W” XF4012-001
4 Border embroidery frame
H 30 cm x W 10 cm (H 12
inches x W 4 inches)
SABF6200D1
(U.S.A.)
SABF6200D1C
(Canada)
BF3:
XF4170-001
5 10 spool stand SA561
(U.S.A.)
SA561C
(Canada)
TS5:
XF4175-001
6 King spool thread stand SA562
(U.S.A.)
SA562C
(Canada)
TS6:
XF4180-001
7 Embroidery card Reader SAECR1
8 Embroidery card –
9 Stabilizer material SA519 BM3:
XE0806-001
Water soluble stabilizer SA520 BM5:
XE0615-001
10 Bobbin work kit SABWRK1
(U.S.A.)
SABWRK1C
(Canada)
BWRK1:
XE9099-001
11 USB mouse XE5334-101
Memo
• All specifications are correct at the time of
printing. Please be aware that some
specifications may change without notice.
Note
• Embroidery cards purchased in foreign
countries may not work with your machine.
• Visit your dealer or nearest authorized
Brother dealer for a complete listing of
optional accessories and embroidery cards
available for your machine.
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS
B-14
Basic
operations
This section provides details on the initial setup procedures as well as descriptions of this
machine’s more useful functions.
Page number starts with “B” in this section.
Chapter1 Getting Ready .......................................................B-16
Chapter2 Sensor Functions
(For models equipped with the sensor function)...................B-52
Chapter 1
B Basic operations
Getting Ready
TURNING THE MACHINE ON/OFF........................17
Setting Your Machine for the First Time ...................................18
LCD SCREEN............................................................20
■ Home Page Screen ................................................................... 20
■ Key Functions........................................................................... 21
Using the Machine Setting Mode Key ......................................22
■ Selecting the “Eco Mode” or “Shutoff Support Mode”............. 25
■ Changing the Pointer Shape When a USB Mouse Is Used ........ 25
■ Selecting the Initial Screen Display.......................................... 25
■ Choosing the Display Language................................................ 26
■
Changing the Background Colors of the Embroidery Patterns
... 26
■ Specifying the Size of Pattern Thumbnails ............................... 27
■ Saving a Settings Screen Image to USB Media.......................... 28
Using the Machine Help Key ...................................................29
LOWER THREADING ..............................................31
Winding the Bobbin..................................................................31
■ Using the Supplemental Spool Pin............................................ 31
■ Using the Spool Pin.................................................................. 34
■ Untangling Thread from Beneath the Bobbin Winder Seat ...... 35
Setting the Bobbin ....................................................................36
UPPER THREADING................................................38
Upper Threading.......................................................................38
Using Threads that Unwind Quickly .........................................41
■ Using the Spool Net................................................................. 41
CHANGING THE EMBROIDERY FOOT...................42
Removing the Embroidery Foot.................................................42
Attaching the Embroidery Foot .................................................42
■ Checking the Needle Drop Point With the Embroidery
Foot “W+” with LED Pointer (For Embroidery foot “W+”
with LED pointer user only) ..................................................... 43
■ Adjusting the LED Pointer (For Embroidery foot “W+”
with LED pointer user only) ..................................................... 44
■ Adjusting the Brightness of the LED Pointer
(For Embroidery foot “W+” with LED pointer user only)......... 44
CHANGING THE NEEDLE .......................................45
About the Needle......................................................................46
BEFORE EMBROIDERING........................................46
Embroidery Step by Step ..........................................................46
About the Embroidery Unit.......................................................47
■ Removing the Embroidery Unit ............................................... 47
■ Attaching the Embroidery Unit ................................................ 47
USING FUNCTIONS BY CONNECTING THE
ACCESSORY TO THE MACHINE .............................49
Using USB Media or Embroidery Card Reader/USB Card Writer
Module*....................................................................................49
Connecting the Machine to the Computer ................................49
Using a USB Mouse ..................................................................50
■ Clicking a Key .......................................................................... 50
■ Changing Pages ........................................................................ 50
TURNING THE MACHINE ON/OFF
Getting Ready
Basic operations B-17
B
1
TURNING THE MACHINE ON/OFF
WARNING
• Use only regular household electricity for the power source. Using other power sources may result in fire,
electric shock, or damage to the machine.
• Make sure that the plugs on the power cord are firmly inserted into the electrical outlet and the power
cord receptacle on the machine. Otherwise, a fire or electric shock may result.
• Do not insert the plug on the power cord into an electrical outlet that is in poor condition.
• Turn the main power to OFF and remove the plug in the following circumstances:
When you are away from the machine
After using the machine
When the power fails during use
When the machine does not operate correctly due to a bad connection or a disconnection
During electrical storms
CAUTION
• Use only the power cord included with this machine.
• Do not use extension cords or multi-plug adapters with many other appliances plugged in to them. Fire or
electric shock may result.
• Do not touch the plug with wet hands. Electric shock may result.
• When unplugging the machine, always turn the main power to OFF first. Always grasp the plug to remove
it from the outlet. Pulling on the cord may damage the cord, or lead to fire or electric shock.
• Do not allow the power cord to be cut, damaged, modified, forcefully bent, pulled, twisted, or bundled.
Do not place heavy objects on the cord. Do not subject the cord to heat. These things may damage the
cord, or cause fire or electric shock. If the cord or plug is damaged, take the machine to your authorized
dealer for repairs before continuing use.
• Unplug the power cord if the machine is not to be used for a long period of time. Otherwise, a fire may
result.
• When leaving the machine unattended, either the main switch of the machine should be turned to OFF or
the plug must be removed from the socket-outlet.
• When servicing the machine or when removing covers, the machine must be unplugged.
• For U.S.A. only
This appliance has a polarized plug (one blade wider than the other). To reduce the risk of electrical
shock, this plug is intended to fit in a polarized outlet only one way.
If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet. Do not modify the plug in any way.
TURNING THE MACHINE ON/OFF
B-18
a
Insert the power supply cord into the power
cord receptacle, then insert the plug into a
wall outlet.
a Main power switch
b Power supply cord
b
Turn the main power switch to “I” to turn
on the machine.
a OFF
b ON
c
When the machine is turned on, the
opening movie is played. Touch anywhere
on the screen to display the Home page
screen.
d
Turn the main power switch to “O” to turn
off the machine.
Setting Your Machine for the First
Time
When you first turn on the machine, set the
language and time/date to your language and local
time/date. Follow the procedure below when the
settings screen appears automatically.
a
Press and to set your local language.
b
Press .
c
The message screen, confirming if you want
to set time/date, appears. To set the
time/date, press ; to cancel the
setting, press .
The screen to set time/date appears.
Memo
• When the machine is turned on a sound will
come from the needle area; this is not a
malfunction.
CAUTION
• Only touch the screen with your finger or the
included touch pen. Do not use a sharp pencil,
screwdriver, or other hard or sharp object. It is
not necessary to press hard on the screen.
Pressing too hard or using a sharp object may
damage the screen.
TURNING THE MACHINE ON/OFF
Getting Ready
Basic operations B-19
B
1
d
Press or to set time/date.
a Press to display the time on the screen.
b Set the year (YYYY), month (MM) and date (DD).
c Select whether 24h or 12h setting to display.
d Set the current time.
e
Press to start using your machine.
The clock starts from 0 second of the time you set.
Note
• The time/date you set may be cleared, if
you don’t turn on the machine for a certain
period.
dc
b
a
LCD SCREEN
B-20
■ Home Page Screen
LCD SCREEN
CAUTION
• Only touch the screen with your finger or the included touch pen. Do not use a sharp pencil, screwdriver,
or other hard or sharp object. It is not necessary to press hard on the screen. Pressing too hard or using a
sharp object may damage the screen.
No. Display Key Name Explanation Page
a “Embroidery” key Attach the embroidery unit and press this key to embroider patterns. E-3
b “Embroidery Edit” key Press this key to combine embroidery patterns. With the “Embroidery
Edit” functions, you can also create original embroidery patterns or
frame patterns.
E-57
b
a
LCD SCREEN
Getting Ready
Basic operations B-21
B
1
■ Key Functions
For additional operational information, refer to page reference number listed above.
No. Display Key Name Explanation Page
a Home page screen
key
Press this key anytime it is displayed to return to the home page screen and
select a different category - “Embroidery” or “Embroidery Edit”.
B-20
b Clock key Press this key to set the clock to your local time. B-18
c Presser foot/Needle
exchange key
Press this key before changing the needle, the presser foot, etc. This key locks
all key and button functions to prevent operation of the machine.
B-42 to
B-45
d Machine help key Press this key to see explanations on how to use the machine. B-29
e Machine setting
mode key
Press this key to change the needle stop position, change the volume of
operation sound, adjust the pattern or screen, and change other machine
settings.
B-22
a
cde b
LCD SCREEN
B-22
Using the Machine Setting Mode Key
Press to change the default machine settings (needle stop position, embroidery speed, opening
display, etc.).
a Select the needle stop position (the needle position when the machine is not operating) to be up or down. Select
the down position when using the pivot key.
b Select the operation of the “Needle Position – Stitch Placement” button from the following two sequences.
Each press of the “Needle Position – Stitch Placement” button:
“ON” – raises the needle, stops it at a nearly lowered position, then lowers it
“OFF” – raises the needle, then lowers it
c Change the shape of the pointer when a USB mouse is used (see page B-25).
d Turn the “Upper and Bobbin Thread Sensor” “ON” or “OFF”. If it is turned “OFF”, the machine can be used without
thread. (see page E-26)
e Change the speaker volume. Increase the number for louder volume, decrease for softer volume.
f Select to save the machine power by setting the “Eco Mode” or the “Shutoff Support Mode” (see page B-25).
g Select the initial screen that is displayed when the machine is turned on (see page B-25).
h Change the display language (see page B-26).
i Press to save the current settings screen image to USB media (see page B-28).
Memo
• Press or next to the page numbers, to display a different settings screen.
CAUTION
• If “Upper and Bobbin Thread Sensor” is set to “OFF”, remove the upper thread. If the machine is used
with the upper thread threaded, the machine will not be able to detect if the thread has become tangled.
Continuing to use the machine with tangled thread may cause damage.
a
d
e
b
c
i
g
h
f
i
LCD SCREEN
Getting Ready
Basic operations B-23
B
1
a Change the brightness of the needle area and work area lights.
b Change the screen display brightness (see page A-18).
c Calibrate the sensor function (For models equipped with the sensor function) (see page B-56).
d Display the service count which is a reminder to take your machine in for regular servicing. (Contact your
authorized dealer for details.)
e Display the total number of stitches sewn on this machine.
f The “No.” is the internal machine number for the machine.
g Display the program version. “Version 1” shows the program version of the LCD panel, “Version 2” shows the
program version of the machine.
Memo
• The latest version of software is installed in your machine. Check with your local authorized Brother
dealer or at “ http://support.brother.com/
” for available updates (see page A-26).
a
b
c
d
g
f
e
LCD SCREEN
B-24
a Select from among 16 embroidery frame displays (see page E-35).
b Change the thread color display on the “Embroidery” screen; thread number, color name (see page E-34).
c When the thread number “#123” is selected, select from six thread brands (see page E-34).
d Adjust the maximum embroidery speed setting (see page E-33).
e Adjust the upper thread tension for embroidering (see page E-30).
f Select the height of the embroidery foot during embroidering (see page E-11).
g Change the initial mode of the display (Embroidery/Embroidery Edit) (see page E-4).
h Change the color of the background for the embroidery display area (see page B-26).
i Change the color of the background for the thumbnail area (see page B-26).
j Press to specify the size of pattern thumbnails (see page B-27).
k Change the display units (mm/inch).
l Adjust the distance between the pattern and the basting stitching (see page E-84).
m Adjusting the position and brightness of the embroidery foot “W+” with LED pointer (see page B-44).
a
d
e
f
b
c
g
j
h
i
m
k
l
LCD SCREEN
Getting Ready
Basic operations B-25
B
1
■ Selecting the “Eco Mode” or
“Shutoff Support Mode”
You can save the machine power by setting the eco
mode or the shutoff support mode.
If you leave the machine without using for a
specified period of time, the machine enters in one
of these modes.
“Eco Mode”;
Machine will enter a sleep mode. Touch the screen
or press the “Start/Stop” button to continue sewing.
“Shutoff Support Mode”;
Machine will enter lower power modes after set
period of time. Turn machine off and then back on
to restart sewing.
Press the “Start/Stop” button or touch the screen
display to recover from these modes.
a
Press .
The settings screen appears.
b
Display page 2 of the settings screen.
c
Use or to select the time until
entering the mode.
■ Changing the Pointer Shape When a
USB Mouse Is Used
In the settings screen, the shape can be selected for
the pointer that appears when a USB mouse is
connected. Depending upon the background color,
select the desired shape from the three that are
available.
a
Press .
The settings screen appears.
b
Display page 1 of the settings screen.
c
Use or to choose the pointer shape
from the three settings available ( ,
and ).
d
Press to return to the original screen.
■ Selecting the Initial Screen Display
The Initial screen that appears on the machine can
be changed.
a
Press .
The settings screen appears.
b
Display page 2 of the settings screen.
Condition Eco Mode Shutoff Support
Mode
Available time OFF, 0 - 120 (minute) OFF, 1 - 12 (hour)
“Start/Stop” button Green flashing Green slow flashing
Suspended function Machine light,
Screen display, LED
pointer
All functions
After recovering The machine starts
from the previous
operation.
You need to turn off
the machine.
Note
• If you turn off the machine while the
machine is in the “Eco Mode” or the
“Shutoff Support Mode”, wait for about 5
seconds before turning on the machine
again.
Memo
• For details on changing the background
color, refer to “Changing the Background
Colors of the Embroidery Patterns” on
page B-26.
Memo
• The setting remains selected even if the
machine is turned off.
LCD SCREEN
B-26
c
Use or to select the setting for the
initial screen display.
* Opening Screen: When the machine is turned on,
the home page screen appears after the opening
movie screen is touched.
* Home Page: When the machine is turned on, the
home page screen appears.
* Embroidery Screen: When the machine is turned
on, the “Embroidery” screen appears if the
embroidery unit is attached to the machine.
d
Press to return to the original screen.
■ Choosing the Display Language
a
Press .
The settings screen appears.
b
Display page 2 of the settings screen.
c
Use and to choose the display
language.
a Display language
d
Press to return to the original screen.
■ Changing the Background Colors of
the Embroidery Patterns
In the settings screen, the background colors can be
changed for the embroidery pattern and pattern
thumbnails. Depending on the pattern color, select
the desired background color from the 66 settings
available. Different background colors can be
selected for the embroidery pattern and pattern
thumbnails.
a
Press .
The settings screen appears.
b
Display page 6 of the settings screen.
c
Press .
a Embroidery pattern background
b Pattern thumbnails background
a
a
b
LCD SCREEN
Getting Ready
Basic operations B-27
B
1
d
Select the background color from the 66
settings available.
a Embroidery pattern background
b Selected color
a Pattern thumbnails background
b Selected color
e
Press to return to the original screen.
■ Specifying the Size of Pattern
Thumbnails
The thumbnails for selecting an embroidery pattern
can be set to be displayed at the smaller size or a
larger size. The larger size is 1.5 times the smaller
size.
a
Press .
The settings screen appears.
b
Display page 6 of the settings screen.
Memo
• The setting remains selected even if the
machine is turned off.
b
a
b
a
LCD SCREEN
B-28
c
Press or to select the desired
thumbnail size.
■ Saving a Settings Screen Image to
USB Media
An image of the settings screen can be saved as a
BMP file.
A maximum of 100 images can be saved on a single
USB media at one time.
a
Insert the USB media into the USB port on
the right side of the machine.
a USB port
b USB media
b
Press .
The settings screen appears. Select the settings
screen page, make the changes that you want, and
then save the screen image.
c
Press .
The image file will be saved to the USB media.
d
Remove the USB media, and then for future
reference, check the saved image using a
computer.
The files for Settings screen images are saved with the
name “S##.BMP”.
* “##” in the name “S##.BMP” will automatically be
replaced with a number between S00 and S99.
Note
• When thumbnail size setting has been
changed the pattern selection screen will
not immediately reflect the chosen size. To
view the patterns with the new thumbnail
size, return to the category selection
screen, and then select the pattern category
again.
Note
• If 100 image files have already been saved
on the USB media, the following message
appears. In this case, delete a file from the
USB media or use different USB media.
LCD SCREEN
Getting Ready
Basic operations B-29
B
1
Using the Machine Help Key
Press to open the machine help screen. Five categories are displayed at the top of the screen.
Press a key to see more information about that category.
displays information about
the operation buttons.
displays information about
threading the machine, changing embroidery
feet, etc. Some of the functions are described
in the movies. Watch these movies for a
better understanding of the functions. Certain
individual threading screens are animated.
displays information about
attaching the embroidery unit, changing
embroidery feet, preparing fabric for
embroidering, checking the tension, etc.
displays troubleshooting
information.
displays information about
cleaning the machine, etc.
LCD SCREEN
B-30
Example: Displaying information about
upper threading
a
Press .
b
Press .
The lower half of the screen will change.
c
Press (upper threading).
The screen shows instructions for threading the
machine.
d
Read the instructions.
* To view video, press of the displayed
instructions.
Press under movie to go back to the
beginning. Press to pause. Press to
restart after pause. Press to close out the
movie.
* Press to view the next page.
* Press to view the previous page.
e
Press to return to the original screen.
LOWER THREADING
Getting Ready
Basic operations B-31
B
1
Winding the Bobbin
Press
in this order to display a video example of
bobbin winding on the LCD (see page B-29).
Follow the steps explained below to complete the
operation.
■ Using the Supplemental Spool Pin
With this machine, you can wind the bobbin
without unthreading the machine. While using the
main spool pin to sew, you can conveniently wind
the bobbin using the supplemental spool pin.
a Supplemental spool pin
a
Turn the main power to ON and open the
top cover.
b
Align the groove in the bobbin with the
spring on the bobbin winder shaft, and set
the bobbin on the shaft.
a Groove in the bobbin
b Spring on the shaft
LOWER THREADING
CAUTION
• The included bobbin was designed specifically
for this machine. If bobbins from other models
are used, the machine will not operate
correctly. Use only the included bobbin or
bobbins of the same type (part code: SA156,
(SFB: XA5539-151)). SA156 is Class 15 type
bobbin.
* Actual size
a This model
b Other models
c 11.5 mm (approx. 7/16 inch)
LOWER THREADING
B-32
c
Set the supplemental spool pin in the “up”
position.
a Supplemental spool pin
d
Place the spool of thread on the
supplemental spool pin, so that thread
unrolls from the front. Push the spool cap
onto the spool pin as far as possible to
secure the thread spool.
a Spool pin
b Spool cap
c Thread spool
e
With your right hand, hold the thread near
the thread spool. With your left hand, hold
the end of the thread, and use both hands to
pass the thread through the thread guide.
a Thread guide
CAUTION
• If the thread spool and/or spool cap are set
incorrectly, the thread may tangle on the spool
pin and cause the needle to break.
• Use the spool cap (large, medium, small, or
special) that is closest in size to the thread
spool. If a spool cap smaller than the thread
spool is used, the thread may become caught
in the slit on the end of the spool and cause
the needle to break.
Memo
• When sewing with fine, cross-wound
thread, use the small spool cap, and leave a
small space between the cap and the
thread spool.
a Spool cap (small)
b Thread spool (cross-wound thread)
c Space
• If a spool of thread whose core is 12 mm
(1/2 inch) in diameter and 75 mm (3 inches)
high is inserted onto the spool pin, use the
special spool cap.
a Spool cap (special)
b 12 mm (1/2 inch)
c 75 mm (3 inches)
LOWER THREADING
Getting Ready
Basic operations B-33
B
1
f
Pass the thread around the pre-tension disk
making sure that the thread is under the
pre-tension disk.
a Pre-tension disk
Make sure that the thread passes under the
pre-tension disk.
b Pre-tension disk
c Pull it in as far as possible.
Check to make sure thread is securely set between
pre-tension disks.
g
Wind the thread clockwise around the
bobbin 5-6 Times.
h
Pass the end of the thread through the guide
slit in the bobbin winder seat, and pull the
thread to the right to cut the thread with
the cutter.
a Guide slit (with built-in cutter)
b Bobbin winder seat
i
Set the bobbin winding switch to the left,
until it clicks into place.
a Bobbin winding switch
The bobbin winding window appears.
CAUTION
• Be sure to follow the process described. If the
thread is not cut with the cutter, and the
bobbin is wound, when the thread runs low it
may tangle around the bobbin and cause the
needle to break.
Memo
• Sliding the bobbin winding switch to the left
switches the machine into bobbin winding
mode.
LOWER THREADING
B-34
j
Press .
Bobbin winding starts automatically. The bobbin
stops rotating when bobbin winding is completed.
The bobbin winding switch will automatically return
to its original position.
k
Cut the thread with scissors and remove the
bobbin.
■ Using the Spool Pin
You can use the main spool pin to wind the bobbin
before sewing. You cannot use this spool pin to
wind the bobbin while sewing.
Note
• changes to while the bobbin
is winding.
• Stay near the machine while winding the
bobbin to make sure the bobbin thread is
being wound correctly. If the bobbin thread
is wound incorrectly, press
immediately to stop the bobbin winding.
• The sound of winding the bobbin with stiff
thread, such as nylon thread for quilting,
may be different from the one produced
when winding normal thread; however, this
is not a sign of a malfunction.
Memo
• You can change the winding speed by
pressing (to decrease) or (to
increase) in the bobbin winding window.
• Press to minimize the bobbin
winding window. Then, you can perform
other operations, such as selecting a
pattern or adjusting the thread tension,
while the bobbin is being wound.
• Press (in top right of the LCD screen)
to display the bobbin winding window
again.
Memo
• When removing the bobbin, do not pull on
the bobbin winder seat. Doing so could
loosen or remove the bobbin winder seat,
and could result in damage to the machine.
CAUTION
• Setting the bobbin improperly may cause the
thread tension to loosen, breaking the needle
and possibly resulting in injury.
LOWER THREADING
Getting Ready
Basic operations B-35
B
1
a
Turn the main power to ON and open the
top cover.
b
Align the groove in the bobbin with the
spring on the bobbin winder shaft, and set
the bobbin on the shaft.
a Groove in the bobbin
b Spring on the shaft
c
Pivot the spool pin so that it angles upward.
Set the thread spool on the spool pin so that
the thread unwinds from the front of the
spool.
a Spool pin
b Spool cap
c Thread spool
d Spool felt
d
Push the spool cap onto the spool pin as far
as possible, then return the spool pin to its
original position.
e
While holding the thread with both hands,
pull the thread up from under the thread
guide plate.
a Thread guide plate
f
Pass the thread through the thread guide.
a Thread guide
g
Pass the thread around the pre-tension disk
making sure that the thread is under the
pre-tension disk.
a Thread guide
b Pre-tension disk
h
Follow steps g through k on page B-33
through B-34.
■ Untangling Thread from Beneath the
Bobbin Winder Seat
If the bobbin winding starts when the thread is not
passed through the pre-tension disk correctly, the
thread may become tangled beneath the bobbin
winder seat.
Wind off the thread according to the following
procedure.
a Thread
b Bobbin winder seat
CAUTION
• Do not remove the bobbin winder seat even if
the thread becomes tangled under the bobbin
winder seat. It may result in injuries.
LOWER THREADING
B-36
a
If the thread becomes tangled under the
bobbin winder seat, press once to
stop the bobbin winding.
b
Cut the thread with scissors near the
pre-tension disk.
a Pre-tension disk
c
Push the bobbin winder switch to the right,
and then raise the bobbin at least 10 cm
(4 inches) from the shaft.
d
Cut the thread near the bobbin and hold the
thread end with your left hand. Unwind the
thread clockwise near the bobbin winder
seat with your right hand as shown below.
e
Wind the bobbin again.
Setting the Bobbin
Press
in this order to display a video example of
the operation on the LCD (see page B-29). Follow
the steps explained below to complete the
operation.
a
Press to lock the keys and buttons,
and then raise the presser foot.
* If the message “OK to automatically lower the
presser foot? ” appears on the LCD screen, press OK
to continue.
The entire screen becomes white, and all keys and
operation buttons are locked.
Note
• Make sure that the thread passes through
the pre-tension disk correctly (page B-33).
CAUTION
• Use a bobbin thread that has been correctly
wound. Otherwise, the needle may break or
the thread tension will be incorrect.
• The included bobbin was designed specifically
for this machine. If bobbins from other models
are used, the machine will not operate
correctly. Use only the included bobbin or
bobbins of the same type (part code: SA156,
(SFB: XA5539-151)). SA156 is Class 15 type
bobbin.
* Actual size
a This model
b Other models
c 11.5 mm (approx. 7/16 inch)
• Before inserting or changing the bobbin, be
sure to press in the LCD, otherwise
injuries may occur if the “Start/Stop” button
or any other button is pressed and the machine
starts sewing.
LOWER THREADING
Getting Ready
Basic operations B-37
B
1
b
Slide the bobbin cover latch to the right.
a Bobbin cover
b Latch
The bobbin cover opens.
c
Remove the bobbin cover.
d
Insert the bobbin with your right hand so
that the end of the thread is on the left, and
then, after pulling the thread firmly around
the tab with your left hand as shown, lightly
pull the thread to guide it through the slit.
a Tab
* Be sure to insert the bobbin correctly.
e
While lightly holding down bobbin with
your right hand as shown, guide the thread
through the slit (a and b).
* At this time, check that the bobbin easily rotates
counterclockwise.
Then, pull the thread toward you to cut it
with the cutter (c).
a Slit
b Cutter (Cut the thread with the cutter.)
The cutter cuts the thread.
Make sure that the thread is correctly
passed through the flat spring of the bobbin
case. If it is not inserted correctly, reinstall
the thread.
a Flat spring
f
Insert the tab in the lower-left corner of the
bobbin cover (1), and then lightly press
down on the right side to close the cover
(2).
CAUTION
• Be sure to install the bobbin so that the thread
unwinds in the correct direction, otherwise
the thread may break or the thread tension will
be incorrect.
Memo
• The order that the bobbin thread should be
passed through the bobbin case is
indicated by marks around the bobbin case.
Be sure to thread the machine as indicated.
CAUTION
• Be sure to hold down the bobbin with your
finger and unwind the bobbin thread
correctly. Otherwise, the thread may break or
the thread tension will be incorrect.
a
UPPER THREADING
B-38
Upper Threading
Press
in this order to display a video example of
the operation on the LCD (see page B-29). Follow
the steps explained below to complete the
operation.
a
Turn the main power to ON.
b
Press the “Presser Foot Lifter” button to
raise the presser foot.
The upper thread shutter opens so the machine can
be threaded.
a Upper thread shutter
c
Press the “Needle Position” button to raise
the needle.
UPPER THREADING
CAUTION
• Be sure to thread the machine properly.
Improper threading can cause the thread to
tangle and break the needle, leading to injury.
Memo
• The automatic threading function can be
used with embroidery machine needle sizes
75/11 through 90/14.
• Thread such as transparent nylon
monofilament thread and thread with a
thickness of 130/20 or thicker cannot be
used with the automatic threading function.
Memo
• This machine is equipped with an upper
thread shutter, allowing you to check that
the upper threading is performed correctly.
Note
• If you try to thread the needle automatically
without raising the needle, the thread may
not thread correctly.
UPPER THREADING
Getting Ready
Basic operations B-39
B
1
d
Pivot the spool pin so that it angles upward.
Set the thread spool on the spool pin so that
the thread unwinds from the front of the
spool.
a Spool pin
b Spool cap
c Thread spool
d Spool felt
e
Push the spool cap onto the spool pin as far
as possible, then return the spool pin to its
original position.
f
While holding the thread with both hands,
pull the thread up from under the thread
guide plate.
a Thread guide plate
g
While holding the thread in your right
hand, pass the thread through the thread
guide in the direction indicated.
CAUTION
• If the thread spool and/or spool cap are set
incorrectly, the thread may tangle on the spool
pin and cause the needle to break.
• Use the spool cap (large, medium, or small)
that is closest in size to the thread spool. If a
spool cap smaller than the thread spool is
used, the thread may become caught in the slit
on the end of the spool and cause the needle
to break.
Memo
• When sewing with fine, cross-wound
thread, use the small spool cap, and leave a
small space between the cap and the
thread spool.
a Spool cap (small)
b Thread spool (cross-wound thread)
c Space
• If a spool of thread whose core is 12 mm
(1/2 inch) in diameter and 75 mm (3 inches)
high is inserted onto the spool pin, use the
special spool cap.
a Spool cap (special)
b 12 mm (1/2 inch)
c 75 mm (3 inches)
UPPER THREADING
B-40
h
Guide the thread down, up, then down
through the groove, as shown in the
illustration.
i
Pass the thread through the needle bar
thread guide (marked “6”) by holding the
thread with both hands and guiding it as
shown in the illustration.
a Needle bar thread guide
j
Press the “Presser Foot Lifter” button to
lower presser foot.
k
Pass the thread through the thread guide
disks (marked “7”). Make sure that the
thread passes through the groove in the
thread guide.
a Groove in thread guide
l
Pull the thread up through the thread cutter
to cut the thread, as shown in the
illustration.
a Thread cutter
Memo
• Look in the upper groove area to check if
the thread catches on the take-up lever
visible inside the upper groove area.
a Look in the upper groove area
Note
• When using thread that quickly winds off
the spool, such as metallic thread, it may be
difficult to thread the needle if the thread is
cut.
Therefore, instead of using the thread
cutter, pull out about 80 mm (approx. 3
inches) of thread after passing it through the
thread guide disks (marked “7”).
a 80 mm (approx. 3 inches) or more
UPPER THREADING
Getting Ready
Basic operations B-41
B
1
m
Press the “Automatic Threading” button to
have the machine automatically thread the
needle.
The thread passes through the eye of the needle.
n
Carefully pull the end of the thread that was
passed through the eye of the needle.
* If a loop was formed in the thread passed through
the eye of the needle, carefully pull on the loop of
thread through to the back of the needle.
o
Pull out about 5 cm (approx. 2 inches) of
the thread, and then pass it under the
presser foot toward the rear of the machine.
Raise the presser foot lever if the presser foot is
lowered.
a About 5 cm (approx. 2 inches)
Using Threads that Unwind
Quickly
■ Using the Spool Net
If using transparent nylon monofilament thread,
metallic thread, or other strong thread, place the
included spool net over the spool before using it.
When using specialty threads, threading must be
done manually.
If the spool net is too long, fold it once to match it to
the spool size before placing it over the spool.
Memo
• When the “Automatic Threading” button is
pressed, the presser foot will be
automatically lowered. After threading is
finished, the presser foot moves back to the
position before the “Automatic Threading”
button was pressed.
Note
• Pulling the loop of thread gently will avoid
needle breakage.
Memo
• If the needle could not be threaded or the
thread was not passed through the needle
bar thread guides, perform the procedure
again starting from step
c.
Then, pass the thread through the eye of
the needle after step
i.
Note
• Some needles cannot be threaded with the
needle threader. In this case, instead of
using the needle threader after passing the
thread through the needle bar thread guide
(marked “6”), manually pass the thread
through the eye of the needle from the front
to the back.
a Spool net
b Thread spool
c Spool pin
d Spool cap
Memo
• When threading the spool with the spool net
on, make sure that 5 cm - 6 cm (approx.
2 inches - 2-1/2 inches) of thread are pulled
out.
• It may be necessary to adjust the thread
tension when using the spool net.
CHANGING THE EMBROIDERY FOOT
B-42
Either embroidery foot “W+” with LED pointer or “W” is included depending on the countries or regions.
The embroidery foot is attached to the machine when purchased, with the connector of the embroidery
foot “W+” with LED pointer unplugged from the machine.
Removing the Embroidery Foot
a
Press the “Needle Position” button to raise
the needle.
b
Press .
* If the message “OK to automatically lower the
presser foot? ” appears on the LCD screen, press OK
to continue.
The entire screen becomes white, and all keys and
operation buttons are locked.
c
Raise the presser foot lever.
For users of embroidery foot “W”, skip step d and
go to step
e.
d
Unplug the connector of the embroidery
foot “W+” from the jack on the back of the
machine.
e
Use the included screwdriver to loosen the
screw of the embroidery foot, then remove
the embroidery foot.
a Screwdriver
b Embroidery foot
c Embroidery foot screw
Remove the embroidery foot.
Attaching the Embroidery Foot
CHANGING THE EMBROIDERY FOOT
CAUTION
• Always press on the screen before changing the embroidery foot. If is not pressed and
the “Start/Stop” button or another button is pressed, the machine will start and may cause injury.
• Only use embroidery feet made for this machine. Using other presser feet may lead to accident or injury.
CAUTION
• Make sure that the embroidery foot is installed
in the correct direction, otherwise the needle
may strike the embroidery foot, breaking the
needle and causing injuries.
CHANGING THE EMBROIDERY FOOT
Getting Ready
Basic operations B-43
B
1
a
Position the embroidery foot “W+” with
LED pointer or “W” on the presser foot bar
by aligning the notch of the presser foot to
the large screw.
Side view
b
Hold the embroidery foot in place with
your right hand, and then use the included
screwdriver to securely tighten the
embroidery foot screw.
For users of embroidery foot “W”, skip step c and
go to step
d.
c
Plug the connector of the embroidery foot
“W+” with LED pointer into the jack on the
back of your machine.
d
Press to unlock all keys and
buttons.
All keys and operation buttons are unlocked, and
the previous screen is displayed.
■ Checking the Needle Drop Point
With the Embroidery Foot “W+”
with LED Pointer (For Embroidery
foot “W+” with LED pointer user
only)
Before beginning to embroider when using the
embroidery foot “W+” with LED pointer, carefully
read the procedures described in the “Embroidery”
and “Embroidery Edit” chapters.
a
Press in the embroidery screen.
The LED pointer indicates the needle drop point.
* The LED pointer turns off automatically by lowering
the presser foot or returning to the previous page.
CAUTION
• Use the included screwdriver to firmly tighten
the screw of the embroidery foot. If the screw
is loose, the needle may strike the embroidery
foot and possibly cause injury.
Memo
• When the LED pointer is turned on, the
presser foot height is automatically adjusted
according to the fabric thickness.
• If is pressed again, the fabric thickness
is remeasured and the presser foot is set to
the optimum height.
Note
• With bulky fabrics, the position may not be
accurate due to the various depths of the
fabrics.
• With fabric that has a very uneven surface
such as quilting, the fabric thickness may
not be correctly measured. In this case, the
pointer indication should be used only as a
reference.
CHANGING THE EMBROIDERY FOOT
B-44
■ Adjusting the LED Pointer (For
Embroidery foot “W+” with LED
pointer user only)
Adjust the LED pointer if it indicates a point different
than the actual needle drop point.
Before adjusting the LED pointer, mark the actual
needle drop point on the fabric to be embroidered,
and then hoop the fabric and attach the embroidery
frame.
a
Press .
The settings screen appears.
b
Display page 7 of the Embroidery settings
screen.
c
Press .
The Embroidery Foot “W+” with LED Pointer
Adjustment screen appears.
a LED pointer adjustment
d
Use or to adjust the LED pointer so
that it indicates the actual needle drop
point.
e
Press twice to return to the original
screen.
■ Adjusting the Brightness of the LED
Pointer (For Embroidery foot “W+”
with LED pointer user only)
a
Follow the steps from a to d to display
the embroidery foot with LED pointer
adjustment screen.
b
Use or to adjust the brightness of
the LED pointer.
c
Press twice to return to the original
screen.
Note
• As a default, some keys mentioned in the
following procedures appear in light gray
and are not available. To enable the keys for
specifying the settings, attach embroidery
foot “W+” with LED pointer to the machine.
The keys are enabled after the embroidery
foot is plugged in.
Note
• The specified setting is saved in the
machine’s memory. This is useful for
positioning during continuous
embroidering.
• For normal use, return the setting to “00”.
a
CHANGING THE NEEDLE
Getting Ready
Basic operations B-45
B
1
a
Press the “Needle Position” button to raise
the needle.
b
Press .
* If the message “OK to automatically lower the
presser foot? ” appears on the LCD screen, press OK
to continue.
The entire screen becomes white, and all keys and
operation buttons are locked.
c
Use the screwdriver to turn the screw
toward the front of the machine and loosen
the screw. Remove the needle.
d
With the flat side of the needle facing the
back, insert the new needle all the way to
the top of the needle stopper (viewing
window) in the needle clamp. Use a
screwdriver to securely tighten the needle
clamp screw.
a Needle stopper
b Hole for setting the needle
c Flat side of needle
e
Press to unlock all keys and
buttons.
CHANGING THE NEEDLE
CAUTION
• Always press on the screen before
changing the needle. If is not pressed
and the Start/Stop button or another operation
button is pressed accidentally, the machine
will start and injury may result.
• Use only embroidery machine needles made
for home use. Other needles may bend or
break and may cause injury.
• Never sew with a bent needle. A bent needle
will easily break and may cause injury.
Memo
• To check the needle correctly, place the flat
side of the needle on a flat surface. Check
the needle from the top and the sides.
Throw away any bent needles.
a Parallel space
b Level surface (bobbin cover, glass, etc.)
Note
• Before replacing the needle, cover the hole
in the needle plate with fabric or paper to
prevent the needle from falling into the
machine.
CAUTION
• Be sure to push in the needle until it touches
the stopper, and securely tighten the needle
clamp screw with a screwdriver. If the needle
is not completely inserted or the needle clamp
screw is loose, the needle may break or the
machine may be damaged.
BEFORE EMBROIDERING
B-46
About the Needle
The needle is probably the most important part of the machine. Choosing the proper needle for your
embroidering project will result in a beautiful finish and fewer problems. Below are some things to keep
in mind about needles.
• Use needle 75/11 for embroidery.
• It is recommended that a 90/14 needle should be used when embroidering on heavyweight fabrics or
stabilizing products (for example, denim, puffy foam, etc.). A 75/11 needle may bend or break, which could
result in injury.
• The smaller the needle number, the finer the needles. As the numbers increase, the needles get thicker.
• Use fine (thinner) needles for lightweight fabrics, and thicker (larger) needles for heavyweight fabrics.
Embroidery Step by Step
Follow the steps below to prepare the machine for embroidery.
BEFORE EMBROIDERING
Step 4
Step 2
Step 1
Step 3, 5
Step 6
Step # Aim Action Page
1 Bobbin thread setup For the bobbin thread, wind embroidery bobbin thread and set it in place. B-31
2 Fabric preparation Attach a stabilizer material to the fabric, and hoop it in the embroidery frame. E-11 to
E-16
3 Pattern selection Turn the main power to ON, and select an embroidery pattern. E-3
4 Embroidery frame attachment Attach the embroidery frame to the embroidery unit. E-17
5 Checking the layout Check and adjust the size and position of the embroidery. E-19
6 Embroidery thread setup Set up embroidery thread according to the pattern. E-21
* It is recommended that a 90/14 needle should be used when embroidering on heavy weight fabrics or stabilizing products (for example;
denim, puffy foam, etc.).
BEFORE EMBROIDERING
Getting Ready
Basic operations B-47
B
1
About the Embroidery Unit
■ Removing the Embroidery Unit
a
Press either (Embroidery) or
(Embroidery Edit), then press
.
The carriage will move to the removal position.
b
Turn the main power to OFF.
c
Hold down the release button, and pull the
embroidery unit away from the machine.
a Release button
■ Attaching the Embroidery Unit
a
Turn the main power to OFF.
CAUTION
• Always remove the embroidery frame before
pressing . Otherwise, the frame may
strike the embroidery foot, and possibly cause
injury.
• The embroidery unit will not fit in the shipping
carton box if this step is not done.
Note
• Be sure to turn off the machine before
removing the embroidery unit, otherwise
damage to the machine may result.
CAUTION
• Do not carry the embroidery unit by holding
the release button compartment.
CAUTION
• Do not move the machine with the embroidery
unit attached. The embroidery unit could fall
off and cause injury.
• Keep your hands and foreign objects away
from the embroidery carriage and frame when
the machine is embroidering. Otherwise,
injury may result.
• To avoid distorting your embroidery design, do
not touch the embroidery carriage and frame
when the machine is embroidering.
Note
• Be sure to turn off the power before
installing the embroidery unit. Otherwise,
the machine may be damaged.
• Do not touch the inner connector of the
embroidery unit. The pins on the
embroidery unit connection may be
damaged.
• Do not apply strong force to the embroidery
unit carriage or pick up the unit by the
carriage. Otherwise, the embroidery unit
may be damaged.
• When not using or when transporting the
embroidery unit, pack it securely in the
shipping carton box.
BEFORE EMBROIDERING
B-48
b
Insert the embroidery unit connection into
the machine connection port. The spring
hinge on the connection port cover will
allow easy access to the port. Push lightly
on the connection port cover until the unit
clicks into place.
a Embroidery unit connection
b Machine connection port
c
Turn the main power to ON.
The following message will appear.
d
Press .
The carriage will move to the initialization position.
Note
• Be sure there is no gap between the
embroidery unit and the machine. If there is
a gap, the embroidery patterns will not
embroider with the correct registration.
• Do not push on the carriage when installing
the embroidery unit onto the machine.
Moving the carriage may damage the
embroidery unit.
Note
• Either “Embroidery” screen or “Embroidery
Edit” screen appears, depending on the
setting selected in the settings screen.
USING FUNCTIONS BY CONNECTING THE ACCESSORY TO THE MACHINE
Getting Ready
Basic operations B-49
B
1
Using USB Media or Embroidery
Card Reader/USB Card Writer
Module*
* If you have purchased the PE-DESIGN Ver5 or later,
PE-DESIGN NEXT, PE-DESIGN Lite, PED-BASIC or
PE-DESIGN PLUS, you can plug the included USB
card writer module into the machine as an
embroidery card reader, and recall patterns.
a USB port for mouse / media (USB 2.0)
b USB media
a USB port for mouse / media
b Embroidery card Reader/USB card writer module*
Connecting the Machine to the
Computer
Using the included USB cable, the machine can be
connected to your computer.
a USB port for computer
b USB cable connector
USING FUNCTIONS BY CONNECTING THE
ACCESSORY TO THE MACHINE
Note
• Use only an embroidery card reader
designed for this machine. Using an
unauthorized embroidery card reader may
cause your machine to operate incorrectly.
• Embroidery patterns cannot be saved from
the machine to an embroidery card inserted
into a connected USB card writer module.
Memo
• USB media is widely used, however some
USB media may not be usable with this
machine. Please visit our website for more
details.
• Depending on the type of USB media being
used, either directly plug the USB device
into the machine’s USB port or plug the
USB media Reader/Writer into the
machine’s USB port.
Note
• The connectors on the USB cable can only
be inserted into a port in one direction. If it
is difficult to insert the connector, do not
insert it with force. Check the orientation of
the connector.
• For details on the position of the USB port
on the computer (or USB hub), refer to the
instruction manual for the corresponding
equipment.
USING FUNCTIONS BY CONNECTING THE ACCESSORY TO THE MACHINE
B-50
Using a USB Mouse
The USB mouse, connected to the machine, can
be used to perform a variety of operations in the
screens.
a USB port for mouse / media
b USB mouse
■ Clicking a Key
When the mouse is connected, the pointer appears
on the screen. Move the mouse to position the
pointer over the desired key, and then click the left
mouse button.
a Pointer
■ Changing Pages
Rotate the mouse wheel to switch through the tabs
of the pattern selection screens.
Note
• If a mouse other than the optional USB
mouse is used, it may not perform as
described in this Operation Manual.
Note
• Do not perform operations with the mouse
at the same time that you are touching the
screen with your finger or the included
touch pen.
• A USB mouse can be connected or
disconnected at any time.
• The mouse pointer does not appear in the
opening screen.
Memo
• Double-clicking has no effect.
a
Memo
• If page numbers and a vertical scroll bar for
additional pages are displayed, rotate the
mouse wheel or click the left mouse button
with the pointer on / or / to
display the previous or next page.
USING FUNCTIONS BY CONNECTING THE ACCESSORY TO THE MACHINE
Getting Ready
Basic operations B-51
B
1
Chapter 2
B Basic operations
Sensor Functions (For models
equipped with the sensor function)
CONNECTING THE SENSOR PEN ...........................53
Using the Sensor Pen Holder ....................................................53
USING THE SENSOR PEN........................................55
Using the Sensor Pen ................................................................55
Important Information about Sensor Pen..................................55
Calibrating the Sensor Pen........................................................56
USING SENSOR FUNCTIONS IN
“EMBROIDERY”/“EMBROIDERY EDIT” MODE ......58
Specifying the Embroidering Position With the Sensor Pen.......58
■ Selecting the Embroidering Position by the Pattern Edge ......... 59
■ Selecting the Embroidering Position by the Pattern Center...... 60
You can activate this function after connecting the sensor pen to the machine.
The sensor pen is included with the machine in some countries or regions.
CONNECTING THE SENSOR PEN
Sensor Functions (For models equipped with the sensor function)
Basic operations B-53
B
2
When connecting the sensor pen to the machine, make sure that the arrow on the sensor pen connector
faces up, lines up with the arrow on the machine, and that the connector is firmly inserted into the jack.
a Sensor pen jack
b Sensor pen connector
Using the Sensor Pen Holder
When connecting the sensor pen to the machine,
attach the sensor pen holder to keep the sensor
pen with the machine.
The right side of the holder can be used to hold the
touch pen.
Sensor pen holder
a
Using the point end of the cleaning brush or
the seam ripper point, remove the
protective cap covering the hole on the
right side of the machine.
Insert the point of the seam ripper or cleaning brush
into the hole in the protective cap, and then lightly
pull out the protective cap to remove it.
b
Firmly insert the sensor pen holder into the
hole where the protective cap was
removed.
CONNECTING THE SENSOR PEN
CAUTION
• When connecting the sensor pen, make sure
that the arrow on the sensor pen connector
faces up and aligns with the arrow on the
machine, otherwise the connector pins will
not align correctly and the connector will be
damaged.
• When connecting or disconnecting the sensor
pen, grab the connector, and then slowly push
it straight in or pull it straight out.
• When disconnecting the sensor pen from the
machine, do not pull on the cord, otherwise
the sensor pen may be damaged.
CONNECTING THE SENSOR PEN
B-54
c
Set the sensor pen in the sensor pen holder
with the pen tip pointing downward, and
then connect the sensor pen to the
machine.
USING THE SENSOR PEN
Sensor Functions (For models equipped with the sensor function)
Basic operations B-55
B
2
Using the Sensor Pen
Hold the sensor pen, and then touch the point to
be specified. When the tip of the sensor pen is
pushed in, the position information is sent to the
machine.
When using the sensor pen, touch slowly and
gently for the definite operation.
1) Touch: Touch a point with the sensor pen, then
immediately lift up the pen.
2) Long touch: Touching a point with the sensor
pen and holding it down for at least one second
allows you to activate the functions that you just
selected.
Important Information about
Sensor Pen
The sensor pen emits the signal to the machine,
and then the sensor pen receiver receives the
signal to specify the position.
a Sensor pen receiver
b Signal is waved out from the sensor pen
USING THE SENSOR PEN
Note
• Once a point is touched with the sensor pen
and the entered information is applied in the
screen, perform the next operation.
Repeatedly touching a point with the sensor
pen may prevent the information from being
correctly read.
• Do not drag the sensor pen tip on the
machine, otherwise the sensor pen tip may
be chipped off.
• If there is any problem with the guideline
marker, the sensor function may not
operate correctly.
Memo
• The sensor pen can be used to touch on the
screen as a touch pen.
CAUTION
• Do not insert any object into the sensor pen
and the receiver, otherwise the machine may
be damaged.
IMPORTANT
• Do not put your hand, the fabric or any object
between the machine and the sensor pen,
otherwise the sensor pen receiver may not
receive the ultrasonic wave.
• Do not use the machine close to any other unit
which produces ultrasonic wave or a vibration
sound, otherwise interference may occur.
USING THE SENSOR PEN
B-56
Calibrating the Sensor Pen
Before using the sensor pen for the first time, be
sure to personalize it using “Sensor Function
Calibration” in the settings screen. Doing so
allows the machine to learn the position in which
you usually hold the pen.
Hold the sensor pen at a comfortable angle and
then calibrate the machine according to the
procedure below.
Be sure to keep the sensor pen at the same angle
while calibrating the first and second points.
a
Press .
b
Display page 3 of the settings screen.
c
Connect the sensor pen to the machine and
then press .
The Sensor Function Calibration screen appears.
d
First touch the green dot marking on the
needle plate cover using the sensor pen.
* Touch on the needle plate cover.
a Needle plate cover
* A beep will sound and the a will change to red. (If
you cannot hear the beep, check that the volume
setting on page 1/7 of your settings is 1 or higher.)
* Press to redo the first point by starting over
from step
d.
e
Touch the second point at the center of the
cross-hair using the sensor pen.
* Touch on the point in the illustrations.
USING THE SENSOR PEN
Sensor Functions (For models equipped with the sensor function)
Basic operations B-57
B
2
a Embroidery unit
f
Press to finish the calibration. To
repeat the calibration touch the first point
again using the sensor pen, and continue
with step
e.
* Press to return to the original screen without
finishing the calibration.
* Press to reset the calibration.
USING SENSOR FUNCTIONS IN “EMBROIDERY”/“EMBROIDERY EDIT” MODE
B-58
Before using the sensor functions, carefully read the procedure in “Embroidery” and “Embroidery Edit” to
familiarize yourself with the machine operations.
Specifying the Embroidering
Position With the Sensor Pen
By using the sensor pen, the embroidering position
can be adjusted to the desired location. This
function can be performed in either “Embroidery”
or “Embroidery Edit” mode, but the procedure
described below is performed in “Embroidery”
mode.
If the message “The carriage of the embroidery
unit will move. Keep your hands etc. away from
the carriage.” appears during the operation, ensure
safety, and then press .
a
Turn on the machine.
b
Press (Embroidery)/
(Embroidery Edit).
c
Select the category for the pattern to be
embroidered.
d
In the pattern selection screen, press the
key for the pattern to be embroidered.
e
Press .
f
Hoop the fabric and attach the embroidery
frame to the machine.
Refer to “Hooping the Fabric in the Embroidery
Frame” on page E-13 and “ATTACHING THE
EMBROIDERY FRAME” on page E-17.
g
Press .
Select the desired area and press when the
following message appears (only for use of the extra
large embroidery frame).
USING SENSOR FUNCTIONS IN
“EMBROIDERY”/“EMBROIDERY EDIT” MODE
USING SENSOR FUNCTIONS IN “EMBROIDERY”/“EMBROIDERY EDIT” MODE
Sensor Functions (For models equipped with the sensor function)
Basic operations B-59
B
2
h
Press .
The embroidering position selection screen appears.
i
Select the method for positioning the
embroidery pattern.
* To align the edge of the embroidery with a pattern
or mark on the fabric, select the edge. If the center of
the pattern to be embroidered is determined, select
the center position.
■ Selecting the Embroidering Position
by the Pattern Edge
a
From on the screen, press the edge
to be the reference for positioning.
b
Press .
c
With the sensor pen, touch the point on the
fabric corresponding to corner a in the
screen.
a Square of pattern edge
b Pattern position
d
With the sensor pen, touch the point on the
fabric corresponding to corner b in the
screen.
a Square of pattern edge
b Pattern position
e
Press to adjust the positions.
If you don’t need to adjust the positions, continue to
step
i.
USING SENSOR FUNCTIONS IN “EMBROIDERY”/“EMBROIDERY EDIT” MODE
B-60
f
Press to move the LED pointer
on the fabric for adjusting the first position.
g
Press to apply the setting.
h
Press to move the LED pointer
on the fabric for adjusting the second
position.
i
Press to apply the setting.
j
The preview in the embroidery screen is
updated according to the specified
embroidering position.
k
Press the “Start/Stop” button to start
embroidering.
■ Selecting the Embroidering Position
by the Pattern Center
a
Press in the following screen.
b
With the sensor pen, touch 2 points on the
fabric corresponding to the numbers in the
center of the embroidery pattern.
a Center line of the pattern
b Pattern position
Specified point number turns into red.
c
Press to adjust the positions.
If you don’t need to adjust the positions, continue to
step
g.
USING SENSOR FUNCTIONS IN “EMBROIDERY”/“EMBROIDERY EDIT” MODE
Sensor Functions (For models equipped with the sensor function)
Basic operations B-61
B
2
d
Press to move the LED pointer
on the fabric for adjusting the first position.
e
Press to apply the setting.
f
Press to move the LED pointer
on the fabric for adjusting the second
position.
g
Press to apply the setting.
h
The preview in the embroidery screen is
updated according to the specified
embroidering position.
i
Press the “Start/Stop” button to start
embroidering.
Note
• When using the sensor pen to specify the
embroidering position, it may not be
possible to exactly specify the desired
location. In this case, move the embroidery
frame to align the center of the pattern with
the location indicated by the LED pointer.
USING SENSOR FUNCTIONS IN “EMBROIDERY”/“EMBROIDERY EDIT” MODE
B-62
Embroidering
This section provides instruction to embroider designs with this machine.
Page number starts with “E” in this section.
The screen display and machine illustration may vary slightly, depending on the countries or
regions.
Chapter1 Embroidery ............................................................. E-2
Chapter2 Embroidery Edit .................................................... E-56
Chapter 1
E Embroidering
Embroidery
SELECTING PATTERNS ..............................................3
■ Copyright Information .............................................................. 3
Selecting Embroidery Patterns/Brother “Exclusives”/
Floral Alphabet/Bobbin Work Patterns .......................................4
Selecting Character Patterns.......................................................5
Selecting Frame Patterns............................................................. 7
Selecting Patterns from Embroidery Cards..................................7
■ About Embroidery Card Reader (Sold Separately) and USB Card
Writer Module*.......................................................................... 7
■ About Embroidery Cards (Sold Separately) ............................... 7
Selecting Patterns from USB Media/Computer ...........................8
VIEWING THE EMBROIDERING SCREEN ................. 9
■ Key Functions........................................................................... 10
PREPARING THE FABRIC ........................................11
Attaching Iron-on Stabilizers (Backing) to the Fabric ...............11
Hooping the Fabric in the Embroidery Frame ..........................13
■ Types of Embroidery Frames .................................................... 13
■ Inserting the Fabric .................................................................. 14
■ Using the Embroidery Sheet .................................................... 15
Embroidering Small Fabrics or Fabric Edges ............................16
■ Embroidering Small Fabrics...................................................... 16
■ Embroidering Edges or Corners................................................ 16
■ Embroidering Ribbons or Tape................................................. 16
ATTACHING THE EMBROIDERY FRAME ................17
■ Removing the Embroidery Frame ............................................. 17
CONFIRMING THE PATTERN POSITION ...............19
Checking the Pattern Position ..................................................19
Previewing the Completed Pattern ..........................................20
■ Frame sizes displayed on screen............................................... 20
SEWING AN EMBROIDERY PATTERN..................... 21
Embroidery Attractive Finishes ................................................21
■ Embroidery Needle Plate Cover .............................................. 22
Sewing Embroidery Patterns .....................................................22
Sewing Embroidery Patterns Which Use Appliqué ...................23
ADJUSTMENTS DURING THE EMBROIDERY
PROCESS..................................................................26
If the Bobbin Runs Out of Thread ............................................26
If the Thread Breaks During Sewing .........................................27
Restarting from the Beginning ..................................................28
Resuming Embroidery After Turning Off the Power..................28
MAKING EMBROIDERY ADJUSTMENTS.................30
Adjusting Thread Tension .........................................................30
■ Correct Thread Tension ........................................................... 30
■ Upper Thread is Too Tight ....................................................... 30
■ Upper Thread is Too Loose ...................................................... 30
Adjusting the Bobbin Case (with No Color on the Screw) ........31
■ Correct Tension ....................................................................... 31
■ Bobbin Thread is Too Loose ..................................................... 31
■ Bobbin Thread is Too Tight ...................................................... 32
Using the Automatic Thread Cutting Function
(END COLOR TRIM).................................................................32
Using the Thread Trimming Function (JUMP STITCH TRIM) ....32
■ Selecting the Length of Jump Stitch Not to Trim...................... 33
Adjusting the Embroidery Speed .............................................. 33
Changing the Thread Color Display ......................................... 34
Changing the “Embroidery Frame Display”.............................. 35
REVISING THE PATTERN ........................................ 36
Moving the Pattern................................................................... 36
Aligning the Pattern and the Needle ........................................ 36
Changing the Size of the Pattern .............................................. 37
Rotating the Pattern ................................................................. 38
Creating a Horizontal Mirror Image ........................................ 39
Enlarging the Editing Screen..................................................... 39
Changing the Density (Alphabet Character and Frame
Patterns Only) ......................................................................... 40
Changing the Colors of Alphabet Character Patterns .............. 40
Embroidering Linked Characters .............................................. 41
Uninterrupted Embroidering
(Monochrome - Using a Single Color) ...................................... 43
USING THE MEMORY FUNCTION......................... 44
Embroidery Data Precautions................................................... 44
■ Types of Embroidery Data that can be Used.............................44
■ Types of USB Devices/Media that can be Used ........................44
■ Connecting Your Machine to the Computer .............................44
■ Precautions on Using the Computer to Create and Save
Data..........................................................................................44
■ Tajima (.dst) Embroidery Data..................................................45
Saving Embroidery Patterns in the Machine’s Memory ............ 45
■ If the Memory is Full.................................................................45
Saving Embroidery Patterns to USB Media............................... 46
Saving Embroidery Patterns in the Computer........................... 47
Retrieving Patterns from the Machine’s Memory .................... 48
Recalling from USB Media ....................................................... 49
Recalling from the Computer ................................................... 50
EMBROIDERY APPLICATIONS................................ 51
Using a Frame Pattern to Make an Appliqué (1)....................... 51
Using a Frame Pattern to Make an Appliqué (2)....................... 52
Sewing Split Embroidery Patterns............................................. 53
SELECTING PATTERNS
Embroidery
Embroidering E-3
E
1
■ Copyright Information
The patterns stored in the machine and embroidery cards are intended for private use only. Any public or
commercial use of copyrighted patterns is an infringement of copyright law and is strictly prohibited.
There are many character and decorative embroidery patterns stored in the machine’s memory (see the “Quick
Reference Guide” for a full summary of patterns in the machine’s memory). You can also use patterns from the
embroidery cards (sold separately).
Once the machine has finished the initialization and the carriage has moved to the start position, the pattern type
selection screen will display.
If another screen is displayed, press , then to display the screen below.
There are 6 categories of patterns in this machine.
a Embroidery patterns
b Brother “Exclusives”
c Floral alphabet patterns
d Frame patterns
e Character patterns
f Bobbin work patterns (see “Appendix”)
g Patterns saved in the machine’s memory (see
page E-48)
h Patterns saved in USB media (see page E-49)
i Patterns saved on the computer (see page E-50)
j Press this key to position the embroidery unit for
storage
SELECTING PATTERNS
a
c
g
b
d
i
e
j
h
f
Memo
• A key that appears stacked, such as
and , indicates that
there are sub-categories, which must be
selected before a pattern selection screen
appears.
SELECTING PATTERNS
E-4
Selecting Embroidery
Patterns/Brother
“Exclusives”/Floral
Alphabet/Bobbin Work Patterns
a
Touch the key of the category of the pattern
you want to embroider.
* Refer to “How to Create Bobbin Work” of
“Appendix” about the bobbin work patterns.
b
Press the key of the pattern you want to
embroider.
* Press to view the next page.
* Press to view the previous page.
The selected pattern is displayed.
c
Press to create a mirror image of the
pattern as needed.
* If a mistake has been made when selecting the
pattern, press the key of the pattern you want to
embroider and the new selection appears.
d
Press .
The embroidery screen is displayed.
e
Proceed to “VIEWING THE
EMBROIDERING SCREEN” on page E-9 to
embroider the pattern.
* To return to the previous screen to select another
pattern, press .
SELECTING PATTERNS
Embroidery
Embroidering E-5
E
1
Selecting Character Patterns
Example: Entering “We Fly”.
a
Press .
b
Press the key of the font you want to
embroider.
c
Press to change the selection screens.
d
Press and then enter “W”.
* If you want to change the size of a character, select
the character and then press to change the
size. The size changes each time you press the key,
from large to medium to small.
* If you make a mistake, press to erase the
mistake.
* If the pattern is too small to see clearly, you can use
the key to check it.
e
Press and enter “e”.
f
Press to enter a space.
Memo
• If you continue adding characters after
changing the size, the new characters will
be entered in the new size.
• You cannot change the size of the entered
characters after combining character stitch
patterns.
SELECTING PATTERNS
E-6
g
Press again and enter “F”.
h
Press and then enter “ly”.
i
Press .
The embroidery screen is displayed.
j
Proceed to “VIEWING THE
EMBROIDERING SCREEN” on page E-9 to
embroider the pattern.
* To return to the previous screen to select another
pattern, press .
SELECTING PATTERNS
Embroidery
Embroidering E-7
E
1
Selecting Frame Patterns
a
Press .
b
Press the key of the frame shape you want
to embroider in the top part of the screen.
a Frame shapes
b Frame patterns
Various frame patterns are displayed at the bottom
part of the screen.
c
Press the key of the frame pattern you want
to embroider.
* If you make a mistake selecting the pattern, press the
key of the pattern you want to embroider.
The selected pattern is displayed on the screen.
d
Press .
The embroidery screen is displayed.
e
Proceed to “VIEWING THE
EMBROIDERING SCREEN” on page E-9 to
embroider the pattern.
* To return to the previous screen to select another
pattern, press .
Selecting Patterns from
Embroidery Cards
■ About Embroidery Card Reader
(Sold Separately) and USB Card
Writer Module*
• Use only an embroidery card Reader designed
for this machine. Using an unauthorized
embroidery card Reader may cause your
machine to operate incorrectly.
* If you have purchased the PE-DESIGN Ver5 or later,
PE-DESIGN NEXT, PE-DESIGN Lite, PED-BASIC or
PE-DESIGN PLUS, you can plug the included USB
card writer module into the machine as an
embroidery card reader, and recall patterns.
■ About Embroidery Cards
(Sold Separately)
• Use only embroidery cards manufactured for this
machine. Using unauthorized cards may cause
your machine to operate incorrectly.
• Embroidery cards sold in foreign countries
cannot be used with this machine.
• Store embroidery cards in the hard case.
a
b
Note
• Embroidery patterns cannot be saved from
the machine to an embroidery card inserted
into a connected USB card writer module*.
SELECTING PATTERNS
E-8
a
Plug the optional embroidery card
Reader/USB card writer module into the
USB port on the machine.
a USB port
b Embroidery card Reader/USB card writer module
b
Insert the card completely into the card
Reader/USB card writer module.
* Insert the embroidery card so that the end with a
printed arrow is facing up.
c
Press the key of the USB port.
The patterns on the embroidery card are displayed
on the selection screen.
d
Follow the steps on page E-4 to select a
pattern.
Selecting Patterns from USB
Media/Computer
To recall patterns from the computer or USB
media, see pages E-49 to E-50.
VIEWING THE EMBROIDERING SCREEN
Embroidery
Embroidering E-9
E
1
a Shows the presser foot code.
Attach embroidery foot “W+” or “W” for all embroidery projects. When the foot presser symbol is displayed on the
screen, you are able to sew.
b Shows the boundary for embroidering with the extra large frame (30 cm 18 cm (approx. 12 inches 7 inches)).
c Shows a preview of the selected pattern.
d Shows the size of the selected pattern.
e Shows the embroidery frames that can be used for the selected pattern. Be sure to use the proper frame (see page
E-13).
f Shows how far the sewing position is from the center (when you move the sewing position).
g Shows the degree of rotation of the pattern.
h Shows how many stitches are in the selected pattern and how many stitches have been sewn so far.
i Shows the time necessary to sew the pattern, and the time already spent sewing the pattern (not including time for
changing and automatically trimming the thread).
j Shows the number of colors in the selected pattern, and the number of the color currently being sewn.
k Shows the part of the embroidery that will be sewn with the first thread color.
l Shows the order for thread color changes and the embroidering time for each thread color.
* The displayed time is the approximate time that will be required. The actual embroidering time may be longer than the
displayed time, depending on the embroidery frame that is used. In addition, the amount of time required to change
thread colors is not included.
m Arrow keys (see next page)
VIEWING THE EMBROIDERING SCREEN
Note
• There is an explanation of additional key functions on the next page.
b
l
a
c
e
f
j
k
m
h i
g
d
VIEWING THE EMBROIDERING SCREEN
E-10
■ Key Functions
Using these keys, you can change the size of the pattern, rotate the pattern, etc.
Note
• Some operations or functions are not
available for certain patterns. If the key
display is light gray, you cannot use that
function or operation with the selected
pattern.
No. Display Key Name Explanation Page
m Arrow keys
( Center key)
Press an arrow key to move the pattern in the direction shown by the arrow.
(Press the Center key to return the pattern to the center of the embroidery
area.)
E-36
n Rotate key Press this key to rotate the pattern. You can rotate a pattern one degree, 10
degrees or 90 degrees at a time.
E-38
o Size key Press this key to change the size of the pattern. E-37
p Multi color key Press this key to change the color of each letter when sewing alphabet
character patterns.
E-40
q Return key Press this key to return to the pattern type selection screen. —
r Cut/Tension key Press this key to specify automatic thread cutting, thread trimming or the
thread tension. For embroidery, these functions are set automatically.
E-32 to
E-32
s Forward/Back key Press this key to move the needle forward or back in the pattern; useful if the
thread breaks while sewing or if you want to start again from the beginning.
E-27 to
E-29
t Trial key Press this key to check the position of the pattern.The embroidery frame moves
to the desired position so you can check that there is enough space to sew the
pattern.
E-19
u Starting point key Press this key to move the needle start position to align the needle with the
pattern position.
E-36
v Memory key Press this key to save a pattern in the machine’s memory, USB media or a
computer.
E-45 to
E-47
w Uninterrupted
embroidery key
Press this key to embroider the selected pattern with a single color. E-43
x Density key Press this key to change the density of alphabet character or frame patterns. E-40
y Embroidery LED foot
key
Press this key to turn on the LED pointer.
“Basic
operations”
z Horizontal mirror
image key
Press this key to create a horizontal mirror image of the pattern. E-39
Q Function page key Press this key to show all the keys in this screen. E-40
R Image key Press this key for a preview of the sewn image. E-20
Q
p
s
R
t
v
u
r
n
o
q
z
x
w
y
PREPARING THE FABRIC
Embroidery
Embroidering E-11
E
1
Attaching Iron-on Stabilizers
(Backing) to the Fabric
For best results in your embroidery projects,
always use stabilizer material for embroidery.
Follow the package instructions for the stabilizer
being used.
When using fabrics that cannot be ironed (such as
towel or fabrics that have loops which expand
when ironed) or in places where ironing is
difficult, position the stabilizer material under the
fabric without fusing it, then position the fabric
and stabilizer in the embroidery frame, or check
with your authorized dealer for the correct
stabilizer to use.
a
Use a piece of stabilizer which is larger
than the embroidery frame being used.
a Size of the embroidery frame
b Iron-on stabilizer (backing)
PREPARING THE FABRIC
CAUTION
• Use fabrics with a thickness of less than 3 mm (approx. 1/8 inch). Using fabrics thicker than 3 mm
(approx. 1/8 inch) may cause the needle to break.
• When using layers with thicker batting etc., you can sew more attractive embroidery by adjusting the
embroidery presser foot height in the embroidery settings screen (see below).
• In the case of thick terry cloth towels we recommend that you place a piece of water soluble stabilizer on
the top surface of the towel. This will help to reduce the nap of the toweling and result in more attractive
embroidery.
Note
• Press . In the “Embroidery Foot
Height” display, use and in the
settings screen. Adjust the presser foot
height for thick or puffy fabrics.
• To increase the space between the presser
foot and the needle plate, set the
embroidery foot height to a larger number,
1.5 mm setting is used for most
embroidery.
CAUTION
• Always use a stabilizer material for embroidery
when sewing stretch fabrics, lightweight
fabrics, fabrics with a coarse weave, or fabrics
which cause pattern shrinkage. Otherwise, the
needle may break and cause injury. Not using
a stabilizer material may result in a poor finish
to your project.
PREPARING THE FABRIC
E-12
b
Iron the iron-on stabilizer material to the
wrong side of the fabric.
a Fusible side of stabilizer
b Fabric (wrong side)
Memo
• When embroidering on thin fabrics such as
organdy or lawn, or on napped fabrics such
as towel or corduroy, use water soluble
stabilizer (sold separately) for best results.
The water soluble stabilizer material will
dissolve completely in water, giving the
project a more attractive finish.
PREPARING THE FABRIC
Embroidery
Embroidering E-13
E
1
Hooping the Fabric in the Embroidery Frame
■ Types of Embroidery Frames
The types and numbers of supplied embroidery frame are differs depending on the countries and regions.
Other optional embroidery frames can be used. When choosing frames that do not appear on the screen, be sure
to check the design size of the embroidery field of the optional frame. Check with your authorized dealer for
frame compatibility.
Select a frame that matches the pattern size. Included frame options are displayed on the LCD.
a Highlighted: Can be used
b Shaded: Cannot be used
Extra Large Large Medium
Embroidery field
30 cm 18 cm
(approx. 12 inches 7 inches)
Embroidery field
18 cm 13 cm
(approx. 7 inches 5 inches)
Embroidery field
10 cm 10 cm
(approx. 4 inches 4 inches)
Use when embroidering
connected or combined
characters or patterns, or when
embroidering large patterns.
Use when embroidering patterns
between 10 cm 10 cm (approx.
4 inches 4 inches) and
18 cm 13 cm (approx. 7 inches
5 inches).
Use when embroidering patterns
under 10 cm 10 cm
(approx. 4 inches 4 inches).
CAUTION
• If you use a frame that is too small, the presser foot may strike the frame during sewing and cause injury.
ab
PREPARING THE FABRIC
E-14
■ Inserting the Fabric
a
Lift-up and loosen the frame adjustment
screw and remove the inner frame.
a Frame adjustment screw
b Inner frame
b
Lay the fabric right side up on top of the
outer frame.
Re-insert the inner frame making sure to align the
inner frame’s with the outer frame’s .
a Inner frame’s
b Outer frame’s
c Frame adjustment screw
c
Slightly tighten the frame adjustment screw,
and then remove the slack in the fabric by
pulling on the edges and corners. Do not
loosen the screw.
d
Gently stretch the fabric taut, and tighten
the frame adjustment screw to keep the
fabric from loosening after stretching.
* After stretching the fabric, make sure the fabric is
taut.
* Make sure the inside and outside frames are even
before you start embroidering.
a Outer frame
b Inner frame
c Fabric
Note
• If the fabric is not securely held in the
embroidery frame, the embroidery design
will sew out poorly. Insert the fabric on a
level surface, and gently stretch the fabric
taut in the frame. Follow the steps below to
insert the fabric correctly.
Memo
• Stretch the fabric from all four corners and
all four edges. While stretching the fabric,
tighten the frame adjustment screw.
PREPARING THE FABRIC
Embroidery
Embroidering E-15
E
1
e
Return the frame adjustment screw to its
initial position.
■ Using the Embroidery Sheet
When you want to embroider the pattern in a
particular place, use the embroidery sheet with the
frame.
a
With a chalk pencil, mark the area of the
fabric you want to embroider.
a Embroidery pattern
b Mark
b
Place the embroidery sheet on the inner
frame. Align the guide lines on the
embroidery sheet with the mark you made
on the fabric.
a Inner frame
b Guide line
c
Gently stretch the fabric so there are no
folds or wrinkles, and press the inner frame
into the outer frame.
a Inner frame
b Outer frame
d
Remove the embroidery sheet.
Memo
• You can use the included screwdriver when
you loosen or tighten the frame adjustment
screw.
PREPARING THE FABRIC
E-16
Embroidering Small Fabrics or
Fabric Edges
Use an embroidery stabilizer to provide extra
support. After embroidering, remove the stabilizer
carefully. Attach the stabilizer as shown in the
following examples. We recommend using a
stabilizer for embroidery.
■ Embroidering Small Fabrics
Use a temporary spray adhesive to adhere the small
piece of fabric to the larger piece in the frame.
If you do not wish to use a temporary spray
adhesive, attach the stabilizer with a basting stitch.
a Fabric
b Stabilizer
■ Embroidering Edges or Corners
Use a temporary spray adhesive to adhere the small
piece of fabric to the larger piece in the frame.
If you do not wish to use a temporary spray
adhesive, attach the stabilizer with a basting stitch.
a Fabric
b Stabilizer
■ Embroidering Ribbons or Tape
Secure with double-sided tape or a temporary spray
adhesive.
a Ribbon or tape
b Stabilizer
ATTACHING THE EMBROIDERY FRAME
Embroidery
Embroidering E-17
E
1
a
Press the “Presser Foot Lifter” button to
raise the presser foot.
b
Align the embroidery frame guide with the
right edge of the embroidery frame holder.
a Embroidery frame holder
b Embroidery frame guide
c
Slide the embroidery frame into the holder,
making sure to align the embroidery frame’s
with the holder’s .
a Arrow mark
d
Lower the frame-securing lever to be level
with the frame to secure the embroidery
frame in the embroidery frame holder.
a Frame-securing lever
■ Removing the Embroidery Frame
a
Raise the frame-securing lever.
ATTACHING THE EMBROIDERY FRAME
Note
• Wind and insert the bobbin before attaching the embroidery frame.
CAUTION
• If the frame-securing lever is not lowered, the
following message appears. You cannot start
sewing until you lower the frame-securing
lever.
ATTACHING THE EMBROIDERY FRAME
E-18
b
Pull the embroidery frame toward you.
CONFIRMING THE PATTERN POSITION
Embroidery
Embroidering E-19
E
1
The pattern is normally positioned in the center of the embroidery frame. If the pattern needs to be
repositioned for better placement on the garment, you can check the layout before starting embroidery.
Checking the Pattern Position
The embroidery frame moves and shows the
pattern position. Watch the frame closely to make
sure the pattern will be sewn in the right place.
a
Press .
The following screen is displayed.
b
From , press the key for the position
that you want to check.
a Selected position
The needle will move to the selected position on the
pattern.
c
Press .
CONFIRMING THE PATTERN POSITION
Memo
• To see the entire embroidering area, press
. The embroidery frame moves and
shows the embroidery area.
CAUTION
• Make sure the needle is up when the
embroidery frame is moving. If the needle is
down, it could break and result in injury.
a
CONFIRMING THE PATTERN POSITION
E-20
Previewing the Completed
Pattern
a
Press .
An image of the pattern as it will be embroidered
appears.
b
Press to select the frame
used in the preview.
* Frames displayed in light gray cannot be selected.
* Press to enlarge the image of the pattern.
* The pattern can be sewn as it appears in the
following display.
■ Frame sizes displayed on screen
c
Press to return to the original screen.
Icon Name
Embroidering area
Extra large embroidery frame
H 30 cm × W 18 cm
(H 11-3/4 inches × W 7-1/8 inches)
Large embroidery frame (optional with some models)
H 18 cm × W 13 cm
(H 7-1/8 inches × W 5-1/8 inches)
Medium embroidery frame (optional with some
models)
H 10 cm × W 10 cm
(H 4 inches × W 4 inches)
Small embroidery frame (optional)
H 2 cm × W 6 cm
(H 3/4 inch × W 2-3/8 inches)
Memo
• You can begin sewing from this screen by
pressing the “Start/Stop” button.
SEWING AN EMBROIDERY PATTERN
Embroidery
Embroidering E-21
E
1
Embroidery Attractive Finishes
There are many factors that go into beautiful embroidery. Using the appropriate stabilizer (see page E-11)
and hooping the fabric in the frame (see page E-13) are two important factors mentioned earlier. Another
important point is the appropriateness of the needle and thread being used. See the explanation of threads
below.
You can adjust thread tension with the screw on the bobbin case. Included bobbin case varies depending
on the type of machine. See the explanation of bobbin case types below.
SEWING AN EMBROIDERY PATTERN
Thread Upper thread Use embroidery thread intended for use with this machine.
Other embroidery threads may not yield optimum results.
Bobbin thread Use embroidery bobbin thread intended for use with this machine.
Memo
• If you use threads other than those listed above, the embroidery may not sew out correctly.
Bobbin case (for the embroidery
and sewing machine)
a Standard bobbin case ;
recommended for sewing and
for embroidering with included
60 weight bobbin thread
(green marking on the screw)
Alternate bobbin case ; for
prewound or other embroidery
bobbin threads
(no color on the screw)
Standard bobbin case (green marking on the screw) originally installed in the machine has a green
marking on the screw. Do not adjust green marked screw.
Alternate bobbin case (no color on the screw) is set with tighter tension for embroidery with
different weights of bobbin threads and a variety of embroidery techniques. This bobbin case is
identified with a dark colored mark on the inside of the bobbin cavity. The screw on this case can
be adjusted if necessary (see page E-31).
This bobbin case is adjusted to accommodate 90 weight bobbin thread, when the machine is
purchased.
Bobbin case (for the embroidery
machine)
a Bobbin case (no color on the
screw) ; recommended for
embroidering with included 90
weight bobbin thread
The bobbin case (no color on the screw) is installed in the machine. We recommend using the
included embroidery bobbin thread. The screw on this case can be adjusted if necessary (see page
E-31).
This bobbin case is adjusted to accommodate 90 weight bobbin thread, when the machine is
purchased.
See “Cleaning the Race” of “Appendix” for how to remove the bobbin case.
CAUTION
• When embroidering on large garments (especially jackets or other heavy fabrics), do not let the fabric
hang over the table. Otherwise, the embroidery unit cannot move freely and the embroidery frame may
strike the needle, causing the needle to bend or break and possibly cause injury.
Place the fabric so that it does not hang off the table or hold the fabric to keep it from dragging.
SEWING AN EMBROIDERY PATTERN
E-22
■ Embroidery Needle Plate Cover
Under some conditions, based on the type of fabric,
stabilizer, or thread being used, there may be some
looping in the upper thread. In this case, attach the
included embroidery needle plate cover to the
needle plate. Attach the cover by inserting the two
projections on the underside of the cover into the
notches on the needle plate as shown below.
a Groove
b Projection
c Notch
To remove the embroidery needle plate cover, place
your fingernail in the groove and lift the plate out.
Sewing Embroidery Patterns
Example:
a Embroidery color order
b Cursor
a
Thread the machine with thread for the first
color, pass the thread through the hole in
embroidery foot, pull out some thread to
give it some slack, and then lightly hold the
end of the thread in your left hand.
Note
• Before embroidering, check that there is enough thread in the bobbin. If you start to sew your
embroidery project without enough thread in the bobbin, you will need to rewind the bobbin in the
middle of the embroidery pattern.
• Do not leave objects in the range of motion of the embroidery frame. The frame may strike the object
and cause a poor finish to the embroidery pattern.
• When embroidering on large garments (especially jackets or other heavy fabrics), do not let the fabric
hang over the table. Otherwise, the embroidery unit cannot move freely, and the pattern may not turn
out as planned.
CAUTION
• Push the embroidery needle plate cover as far
as possible to attach it. If the embroidery
needle plate cover is not securely attached, it
may cause the needle to break.
Note
• Do not use the embroidery needle plate
cover for any applications other than
embroidery.
Memo
• The [+] cursor moves over the pattern, showing
which part of the pattern is being sewn.
b
a
SEWING AN EMBROIDERY PATTERN
Embroidery
Embroidering E-23
E
1
b
Lower the presser foot, then press the
“Start/Stop” button to start embroidering.
After 5-6 stitches, press the “Start/Stop”
button again to stop the machine.
c
Trim the excess thread at the end of the
seam. If the end of the seam is under the
presser foot, raise the presser foot, then
trim the excess thread.
d
Press the “Start/Stop” button to start
embroidering.
When the first color is completely sewn, the machine
will automatically trim the threads and stop. The
presser foot will then automatically be raised.
On the embroidery color order display, the next
color will move to the top.
e
Remove the thread for the first color from
the machine. Thread the machine with the
next color.
f
Repeat the same steps for embroidering the
remaining colors.
When the last color is sewn, “Finished sewing” will
appear on the display. Press , and the display
will return to the original screen.
Sewing Embroidery Patterns
Which Use Appliqué
There are some patterns which call for an appliqué
inside the pattern. Prepare the base fabric and the
appliqué fabric (appliqué piece).
When sewing an embroidery pattern with an
appliqué, the color sewing order display shows
“APPLIQUE MATERIAL”, “APPLIQUE POSITION”,
“APPLIQUE”, and then the sewing order of the
colors around the appliqué.
Memo
• If there is thread left over from the beginning
of sewing, it may be sewn over as you
continue embroidering the pattern, making
it very difficult to deal with the thread after
the pattern is finished. Trim the threads at
the beginning of each thread change.
Memo
• The Thread Trimming Function is originally
set to trim excess thread jumps (threads
linking parts of the pattern, etc.). Depending
on the type of thread and fabric that are
used, an end of upper thread may remain
on the surface of the fabric at the beginning
of the stitching. After embroidering is
finished, cut off this excess thread.
If the setting has been turned off, trim the
excess thread jumps using scissors after
the pattern is finished.
See page E-32 for information on the thread
trimming function.
Memo
• Depending on the thread color display
setting, the display may show ,
, or .
SEWING AN EMBROIDERY PATTERN
E-24
a
Attach an iron-on stabilizer to the wrong
side of the appliqué material.
a Appliqué material (cotton, felt, etc.)
b Iron-on stabilizer
b
Place the appliqué material into the
embroidery frame, and then press the
“Start/Stop” button to sew the outline of
the appliqué.
a Outline of appliqué
b Appliqué material
The machine will sew around the outline of the
appliqué pieces and will then stop.
c
Remove the appliqué material from the
embroidery frame, and then cut carefully
along the stitching. After cutting, remove all
of the stitching thread carefully.
* Carefully cut out the pattern on the outline you just
sewed. Do not cut inside the stitching line, as the
appliqué fabric will not be caught by the appliqué
stitch.
d
Place the base material into the embroidery
frame.
a Base material
e
Press the “Start/Stop” button to sew the
position of the appliqué.
* Use the same thread color you plan to use when
attaching the appliqué in step g.
a Position of appliqué
b Base material
The machine will sew around the position of the
appliqué and will then stop.
f
Apply a thin layer of adhesive or spray
adhesive to the back of the appliqué piece
and attach it to the appliqué position so that
it follows the seam of the outline.
Memo
• The embroidery procedure is the same as
the basic procedure explained on
page E-22.
Memo
• If the appliqué material is a lightweight
fabric, you may want to use a fusible web
on the back to stabilize the fabric and for
appliqué placement. Fuse appliqué in place
with an iron.
Do not remove fabric from the frame to iron
the appliqué material.
SEWING AN EMBROIDERY PATTERN
Embroidery
Embroidering E-25
E
1
g
Press the “Start/Stop” button.
The appliqué will then be completed.
h
Change the upper thread and then carry out
the rest of the embroidering.
Memo
• Some patterns may not show all three
appliqué steps. Sometimes the
“APPLIQUE” step will be shown as a color.
Memo
• Some glue may get onto the presser foot,
needle, and needle plate at this time. Finish
embroidering the appliqué pattern and then
clean away the glue.
• For best sewing results clip all threads
between color steps.
ADJUSTMENTS DURING THE EMBROIDERY PROCESS
E-26
If the Bobbin Runs Out of Thread
When the bobbin begins to run out of thread
during embroidering, the machine will stop and
the message below will appear. Press and
follow the directions below to rethread the lower
threading. If very little sewing remains, you can
embroider 10 final stitches without rethreading the
machine by pressing . The machine will stop
after sewing the 10 stitches.
a
Press .
After the thread is automatically cut, the carriage
will move.
b
Unlock the frame-securing lever and
remove the embroidery frame.
* Be careful not to apply strong force to the fabric at
this time. Otherwise, the fabric may loosen in the
frame.
c
Insert a wound bobbin into the machine.
(see “Setting the Bobbin” of “Basic
operations”.)
d
Press .
The carriage will return to its original position.
e
Attach the embroidery frame.
f
To return to the spot in the pattern where
you stopped sewing, follow steps
c
through
f in the next section.
ADJUSTMENTS DURING THE EMBROIDERY PROCESS
Note
• Be careful not to bump the embroidery unit carriage or the presser foot when removing or attaching
the embroidery frame. Otherwise, the pattern will not embroider correctly.
Note
• If “Upper and Bobbin Thread Sensor” in the
settings screen of the machine setting
mode is set to “OFF”, the message shown
above does not appear.
ADJUSTMENTS DURING THE EMBROIDERY PROCESS
Embroidery
Embroidering E-27
E
1
If the Thread Breaks During
Sewing
a
Press the “Start/Stop” button to stop the
machine.
b
If the upper thread is broken, redo the
upper threading. If the bobbin thread is
broken, press and follow the
directions in steps
a through e from the
previous section to reset the bobbin.
c
Press .
d
Press , , , or to move
the needle back the correct number of
stitches before the spot where the thread
broke.
* If you cannot move back to the spot where the
thread broke, press to select the color and
move to the beginning position of that color, then
use , , , or to move ahead
to slightly before where the thread broke.
e
Press to return to the original screen.
f
Press the “Presser Foot Lifter” button to
lower the presser foot, and press the
“Start/Stop” button to continue sewing.
ADJUSTMENTS DURING THE EMBROIDERY PROCESS
E-28
Restarting from the Beginning
a
Press .
b
Press .
The embroidery frame moves, returning the needle
to the pattern’s beginning position.
c
Press the “Presser Foot Lifter” button to
lower the presser foot and start sewing.
Resuming Embroidery After
Turning Off the Power
The current color and stitch number are saved
when embroidery is stopped. The next time the
machine is turned on, you have the option to
continue or delete the pattern.
a Current stitch number when embroidery was
stopped
a
Turn the main power to ON.
b
Follow the instructions shown on the screen
and remove the embroidery frame.
The following message will appear.
Memo
• Even if the power goes out in the middle of
embroidery, the machine returns to the
point where embroidery was stopped when
the machine is turned on again.
Note
• Do not remove the embroidery unit or the
memory will no longer remember your
design.
a
ADJUSTMENTS DURING THE EMBROIDERY PROCESS
Embroidery
Embroidering E-29
E
1
c
Attach the embroidery frame and press
.
The previous embroidery screen displayed before
the machine was turned off appears.
d
Continue embroidering.
a Stitch number when embroidery is resumed
Memo
• If you want to start a new embroidery
pattern, press so the pattern
selection screen appears.
a
MAKING EMBROIDERY ADJUSTMENTS
E-30
Adjusting Thread Tension
When embroidering, the thread tension should be
set so that the upper thread can slightly be seen on
the wrong side of the fabric.
■ Correct Thread Tension
The pattern can be seen from the wrong side of the
fabric. If the thread tension is not set correctly, the
pattern will not finish well. The fabric may pucker or
the thread may break.
a Right side
b Wrong side
Follow the operations described below to adjust
thread tension according to the situation.
■ Upper Thread is Too Tight
The tension of the upper thread is too tight, resulting
in the bobbin thread being visible from the right side
of the fabric.
a Right side
b Wrong side
a
Press .
b
Press to weaken the upper thread
tension. (The tension number will
decrease.)
c
Press .
■ Upper Thread is Too Loose
The tension of the upper thread is too loose,
resulting in a loose upper thread, loose thread locks,
or loops appearing on the right side of the fabric.
a Right side
b Wrong side
a
Press .
MAKING EMBROIDERY ADJUSTMENTS
Note
• If the thread tension setting is made
extremely weak, the machine may stop
during sewing. This is not the sign of a
malfunction. Increase the thread tension
slightly, and begin sewing again.
Memo
• If you turn the main power to OFF or select
a different pattern, the thread tension will
reset to the automatic setting.
• When you retrieve a saved pattern, the
thread tension setting will be the same as
when the pattern was saved.
Note
• If the bobbin thread was incorrectly
threaded, the upper thread may be too
tight. In this case, refer to “Setting the
Bobbin” of “Basic operations” and rethread
the bobbin thread.
Note
• If the upper thread was incorrectly
threaded, the upper thread may be too
loose. In this case, refer to “Upper
Threading” of “Basic operations” and
rethread the upper thread.
MAKING EMBROIDERY ADJUSTMENTS
Embroidery
Embroidering E-31
E
1
b
Press to tighten the upper thread
tension. (The tension number will increase.)
c
Press .
Adjusting the Bobbin Case (with
No Color on the Screw)
The bobbin case (with no color on the screw) can
be adjusted when bobbin tension changes are
required to accommodate different bobbin
threads. See “Embroidery Attractive Finishes” on
page E-21.
To adjust the bobbin tension for embroidery
function, using the bobbin case (with no color on
the screw), turn the slotted-head screw (-) with a
(small) screwdriver.
a Do not turn a phillips screw (+).
b Adjust with a screwdriver (small).
■ Correct Tension
Upper thread slightly appears on the wrong side of
fabric.
a Right side
b Wrong side
■ Bobbin Thread is Too Loose
Bobbin thread appears slightly on the right side of
fabric.
a Right side
b Wrong side
If this occurs, turn the slotted-head screw (-)
clockwise, being careful not to over-tighten the
screw, approximately 30-45 degrees to increase
bobbin tension.
Note
• With “Embroidery Tension” on the setting
screen, the tension of the upper thread can
be adjusted for embroidering. The selected
setting will be applied to all patterns.
When embroidering, if the overall tension of
the upper thread is too tight or too loose,
adjust it from the setting screen. Press
to tighten the upper thread tension and
press to loosen the upper tension. If an
individual embroidery pattern needs
additional fine tuning, refer to “Adjusting
Thread Tension” on page E-30.
MAKING EMBROIDERY ADJUSTMENTS
E-32
■ Bobbin Thread is Too Tight
Upper thread on the right side of fabric seems to be
lifting/looping and bobbin thread is not seen on the
wrong side of fabric.
a Right side
b Wrong side
If this occurs, turn the slotted-head screw (-)
counterclockwise, being careful not to over-loosen
the screw, approximately 30-45 degrees to decrease
bobbin tension.
Using the Automatic Thread
Cutting Function
(END COLOR TRIM)
The automatic thread cutting function will cut
the thread at the end of sewing each color. This
function is initially turned on. To turn this function
off, press key and then . This function can
be turned on or off during embroidering.
* This setting returns to its default
when the machine is turned off.
a
Press .
b
Press to turn off the automatic thread
cutting function.
The key will display as
* When one color thread is sewn, the machine will
stop without cutting the thread.
Using the Thread Trimming
Function (JUMP STITCH TRIM)
The thread trimming function will
automatically trim any excess thread jumps within
the color. This function is initially turned on. To
turn this function off, press key and then
. This function can be turned on or off during
embroidering.
* Your customized setting remains after turning the
machine off and on.
a Jump stitch
CAUTION
• When adjusting the bobbin case, be sure to
remove the bobbin from the bobbin case.
• DO NOT adjust the position of the phillips (+)
screw on the bobbin case as this may result in
damage to the bobbin case, rendering it
unusable.
• If the slotted-head screw (-) is difficult to turn,
do not use force. Turning the screw too much
or providing force in either (rotational)
direction may cause damage to the bobbin
case. Should damage occur, the bobbin case
may not maintain proper tension.
MAKING EMBROIDERY ADJUSTMENTS
Embroidery
Embroidering E-33
E
1
a
Press .
b
Press to turn off the thread trimming
function.
The key will display as
* The machine will not trim the thread before moving
to the next stitching.
■ Selecting the Length of Jump Stitch
Not to Trim
When the thread trimming function is turned
on, you can select the length of the jump stitch not
to trim the thread. This function can be turned on or
off during embroidering.
Select a setting from 5 mm to 50 mm in 5 mm
increments.
* Your customized setting remains after turning the
machine off and on.
Press or to select the length of jump stitch.
For example: Press to select 25 mm (1 inch)
and the machine will not trim a jump stitch of 25
mm or less before moving to the next stitching.
Adjusting the Embroidery Speed
a
Press .
b
In the “Max Embroidery Speed” display, use
to change the maximum
embroidery speed.
* You can choose from 3 different speed levels, 350
spm, 600 spm or 1050 spm.
Note
• When this function is turned on, use the
included ball point needle 75/11 for
embroidering patterns with short jump
stitches such as alphabet characters. Using
other needles may cause the thread to
break.
Note
• If design has many trims it is recommended
to select a higher jump stitch trim setting in
order to reduce the amount of excess tails
on backside of fabric.
• The higher number of the jump stitch length
selected, the fewer number of times the
machine will trim. In this case, more jump
stitches remain on the surface of the fabric.
MAKING EMBROIDERY ADJUSTMENTS
E-34
c
Press .
Changing the Thread Color
Display
You can display the name of the thread colors or
embroidery thread number.
a
Press .
b
In the “Thread Color Display”, use
to display the name of the thread colors or
the embroidery thread number.
c
When the thread number is
displayed, use to select from six
embroidery thread brands pictured below.
* Depending on the country or area, cotton-like
polyester thread is sold.
d
Press .
Memo
• “spm” is the number of stitches sewn in one
minute.
• Decrease the sewing speed when
embroidering on thin, thick, or heavy
fabrics.
• The sewing speed can be changed after an
embroidery has been started.
• The maximum sewing speed setting does
not change until a new setting is selected.
The setting specified before the main power
is set to OFF remains selected the next time
that the machine is turned on.
• Decrease the sewing speed to 600 spm
when using a speciality thread like a
metallic thread.
• While selecting the bobbin work pattern, the
embroidery speed recommendation is set at
“100 spm”; however you can choose from
100 spm, 200 spm or 350 spm.
Memo
• Colors on the screen may vary slightly from
actual spool colors.
EMBROIDERY / POLYESTER
THREAD#
COUNTRY/COTTON THREAD#
*
MADEIRA /POLYESTER
THREAD#
MADEIRA RAYON THREAD#
SULKY THREAD#
ROBISON-ANTON/POLYESTER
THREAD#
#123
MAKING EMBROIDERY ADJUSTMENTS
Embroidery
Embroidering E-35
E
1
Changing the “Embroidery Frame
Display”
a
Press .
b
In the “Embroidery Frame Display”, use
to change the embroidery frame display
mode.
* There are 16 choices.
* For the optional embroidery frame.
a Extra large frame embroidering area
30 cm × 18 cm (11-3/4 inches × 7-1/8 inches)
b Center mark
c Large frame embroidering area
18 cm × 13 cm (7-1/8 inches × 5-1/8 inches)
d Embroidering area for optional border embroidery
frame
18 cm × 10 cm (7-1/8 inches × 4 inches)
e Embroidery area for optional quilt embroidery
frame
15 cm × 15 cm (6 inches × 6 inches)
f Medium frame embroidering area
10 cm × 10 cm (4 inches × 4 inches)
g Embroidery area for optional small embroidery
frame
2 cm × 6 cm (3/4 inch × 2-3/8 inches)
h Embroidery area for optional border embroidery
frame
30 cm x 10 cm (11-3/4 inches x 4 inches)
i Grid lines
c
Press .
REVISING THE PATTERN
E-36
Moving the Pattern
Use to move the pattern in the direction
shown by the arrow.
Press to center the pattern.
a Distance from the center
The pattern can also be moved by dragging it.
If a USB mouse is connected, move the mouse to
position the pointer on the desired pattern, and
then select and drag the pattern. The pattern can
also be dragged by selecting it directly in the
screen with your finger or the touch pen.
Aligning the Pattern and the
Needle
Example: Aligning the lower left side of a
pattern and the needle
REVISING THE PATTERN
CAUTION
• When you have revised the pattern, check the display of available embroidery frames and use an
appropriate frame. If you use an embroidery frame not displayed as available for use, the presser foot may
strike the frame and possibly cause injury.
Memo
• Patterns cannot be moved in screens where
does not appear.
a
REVISING THE PATTERN
Embroidery
Embroidering E-37
E
1
a
Mark the embroidery start position on the
fabric, as shown.
b
Press .
c
Press .
a Start position
b This key is used for aligning linked characters (see
page E-41).
The needle position moves to the bottom left corner
of the pattern (the embroidery frame moves so that
the needle is positioned correctly).
d
Press .
e
Use to align the needle and the mark
on the fabric, and begin embroidering the
pattern.
Changing the Size of the Pattern
a
Press .
b
Select the direction in which to change the
size.
* Press to enlarge the pattern proportionately.
* Press to shrink the pattern proportionately.
* Press to stretch the pattern horizontally.
* Press to compact the pattern horizontally.
* Press to stretch the pattern vertically.
* Press to compact the pattern vertically.
* Press to return the pattern to its original
appearance.
a
b
REVISING THE PATTERN
E-38
a Size of the pattern
c
Press to return to the original screen.
Rotating the Pattern
a
Press .
b
Select the angle of rotation for the pattern.
* Press to rotate the pattern 90 degrees to the
left.
* Press to rotate the pattern 90 degrees to the
right.
* Press to rotate the pattern 10 degrees to the
left.
* Press to rotate the pattern 10 degrees to the
right.
* Press to rotate the pattern 1 degree to the left.
* Press to rotate the pattern 1 degree to the
right.
* Press to return the pattern to its original
position.
Memo
• Some patterns or characters can be
enlarged more than others.
• Some patterns or characters can be
enlarged to a greater degree if they are
rotated 90 degrees.
• You can change the size of the pattern by
rotating the mouse wheel. Rotate the
mouse wheel away from you to shrink the
pattern. Rotate the mouse wheel toward
you to enlarge the pattern.
a
REVISING THE PATTERN
Embroidery
Embroidering E-39
E
1
a Degree of rotation
c
Press to return to the original screen.
Creating a Horizontal Mirror
Image
Press so it appears as to create a
horizontal mirror image of the selected pattern.
Press again to return the pattern to normal.
Enlarging the Editing Screen
Enlarge the editing screen by pressing .
Press to close the enlarged screen.
0°
Memo
• You can rotate the pattern by rotating the
mouse wheel. Rotate the mouse wheel
away from you to rotate the pattern 10
degrees to the left. Rotate the mouse wheel
toward you to rotate the pattern 10 degrees
to the right.
a
REVISING THE PATTERN
E-40
Changing the Density
(Alphabet Character and Frame
Patterns Only)
The thread density for some alphabet character
and frame patterns can be changed.
A setting between 80% and 120% in 5%
increments can be specified.
a
Press .
* Press to display all the function keys on the
screen.
b
Change the density.
* Press to make the pattern less dense.
* Press to make the pattern more dense.
a Normal
b Fine (stitches closer together)
c Coarse (stitches farther apart)
The pattern density changes each time you press a
button.
c
Press to return to the pattern
selection screen.
Changing the Colors of Alphabet
Character Patterns
Combined alphabet character patterns can be
sewn with each letter in a different color. If
“MULTI COLOR” is set, the machine stops after
each character is sewn so that the thread can be
changed to a different color.
a
Press so that it appears as .
* Press to display all the function keys on the
screen.
* Press the key again to return to the original setting.
REVISING THE PATTERN
Embroidery
Embroidering E-41
E
1
b
After a character is sewn, change the thread
color, and then sew the next character.
Embroidering Linked Characters
Follow the procedure described below to
embroider linked characters in a single row when
the entire pattern extends beyond the embroidery
frame.
Example: Linking “DEF” to the characters
“ABC”
a
Select the character patterns for “ABC”.
b
Press .
c
Press .
The needle is positioned in the lower-left corner of
the pattern. The embroidery frame moves so that the
needle is positioned correctly.
Note
• For details on selecting character patterns,
refer to “Selecting Character Patterns” on
page E-5.
Note
• To cancel the starting point setting and
return the starting point to the center of the
pattern, press .
• Use to select a different starting
point for embroidering.
REVISING THE PATTERN
E-42
d
Press .
e
Press .
f
Press to turn off the thread cutting
function and then press .
g
Press the “Start/Stop” button.
h
After the characters are embroidered, cut
the threads to a generous length, remove
the embroidery frame, and then attach the
embroidery frame again so that the
remaining characters (“DEF”) can be
embroidered.
a End of the embroidering
i
As in step a, select the character patterns
for “DEF”.
j
Press .
k
Press .
The needle is positioned in the lower-left corner of
the pattern. The embroidery frame moves so that the
needle is positioned correctly.
l
Press .
REVISING THE PATTERN
Embroidery
Embroidering E-43
E
1
m
Use to align the needle with the end
of embroidering for the previous pattern.
n
Press the “Start/Stop” button to begin
embroidering the remaining character
patterns.
Uninterrupted Embroidering
(Monochrome - Using a Single
Color)
A selected pattern can be stitched out in one color
instead of multicolor. The machine will hesitate
but not stop between color steps, and then
continue till the pattern is completed. Press
for the multicolor steps to become shaded and the
selected pattern will embroider in a single color,
instead of changing the thread while
embroidering. Press again to return to the
pattern’s original settings.
* Press to display all the function keys on the
screen.
The thread color displayed on the screen will be
grayed out.
Memo
• Even if uninterrupted embroidering has
been set, the automatic thread cutting
function and the thread trimming function
can be used (see page E-32).
USING THE MEMORY FUNCTION
E-44
Embroidery Data Precautions
Observe the following precautions when using
embroidery data other than that created and saved
in this machine.
■ Types of Embroidery Data that can
be Used
• Only .pes, .phc, and .dst embroidery data files
can be used with this machine. Using data other
than that saved using our data design systems or
machines may cause the embroidery machine to
malfunction.
■ Types of USB Devices/Media that
can be Used
Stitch data can be saved to or recalled from USB
media. Use media that meets the following
specifications.
• USB Flash drive (USB Flash memory)
• USB Floppy disk drive
Stitch data can be recalled only.
• USB CD-ROM, CD-R, CD-RW drives
You can also use the following types of media with
the USB Memory Card Reader/USB card writer
module.
• Secure Digital (SD) Card
• CompactFlash
• Memory Stick
•Smart Media
• Multi Media Card (MMC)
• XD-Picture Card
■ Connecting Your Machine to the
Computer
• Compatible models:
IBM PC with a USB port as standard equipment
IBM PC-compatible computer equipped with a
USB port as standard equipment
• Compatible operating systems:
Microsoft Windows XP, Windows Vista,
Windows 7, Windows 8
■ Precautions on Using the Computer
to Create and Save Data
• If the name of the embroidery data file/folder
cannot be identified, for example, because the
name contains special characters, the file/folder
is not displayed. If this occurs, change the name
of the file/folder. We recommend using the 26
letters of the alphabet (uppercase and
lowercase), the numbers 0 through 9,”-”, and
“_”.
• If embroidery data larger than 30 cm × 18 cm
(approx.12 inches × 7 inches) is selected, a
message is shown asking if you wish to rotate the
pattern 90 degrees.
Even after being rotated 90 degrees, embroidery
data larger than 30 cm 18 cm (approx.
12 inches 7 inches) cannot be used.
(All designs must be within the 30 cm 18 cm
(approx. 12 inches 7 inches) design field size.)
• .pes files saved with the number of stitches or the
number of colors exceeding the specified limits
cannot be displayed. The combined design can
not exceed a maximum number of 500,000
stitches or a maximum number of 125 color
changes (Above numbers are approximate,
depending on the overall size of the design). Use
one of our design software programs to edit the
embroidery pattern so that it meets these
specifications.
• Embroidery data stored in a folder created in
USB media can be retrieved.
USING THE MEMORY FUNCTION
CAUTION
• When using embroidery data other than our
original patterns, the thread or needle may
break when sewing with a stitch density that is
too fine or when sewing three or more
overlapping stitches. In that case, use one of
our original data design systems to edit the
embroidery data.
Note
• The processing speed may vary by quantity
of data stored.
• Some USB media may not be usable with
this machine. Please visit our website for
more details.
• The access lamp will begin blinking after
inserting USB devices/media, and it will
take about 5 to 6 seconds to recognize the
devices/media. (Time will differ depending
on the USB device/media).
Memo
• To create file folders, use a computer.
• Letters and numerals can be used in the file
names. In addition, if the file name contains
no more than eight characters, the entire file
name will appear on the screen.
If the file name is more than eight
characters long, only the first six characters
followed by “~” and a number appear as
the file name.
USING THE MEMORY FUNCTION
Embroidery
Embroidering E-45
E
1
• Do not create folders in “Removable Disk” on a
computer. If embroidery data is stored in a folder
in “Removable Disk”, that embroidery data
cannot be retrieved by the machine.
• Even if the embroidery unit is not attached, the
machine will recognize embroidery data.
■ Tajima (.dst) Embroidery Data
• .dst data is displayed in the pattern list screen by
file name (the actual image cannot be displayed).
Only the first eight characters of the file name
can be displayed.
• Since Tajima (.dst) data does not contain specific
thread color information, it is displayed with our
default thread color sequence. Check the
preview and change the thread colors as desired.
Saving Embroidery Patterns in the
Machine’s Memory
You can save embroidery patterns that you have
customized and will use often; for example, your
name, patterns that have been rotated or had the
size changed, patterns that have had the sewing
position changed, etc. A total of about 1MB of
patterns can be saved in the machine's memory.
a
Press when the pattern you want to
save is in the embroidery screen.
b
Press .
* Press to return to the original screen without
saving.
The “Saving” screen is displayed. When the pattern
is saved, the display returns to the original screen
automatically.
■ If the Memory is Full
If the screen below displays, either the maximum
number of patterns have been saved or the pattern
you want to save takes a lot of memory, and the
machine cannot save it. If you delete a previously
saved pattern, you can save the current pattern.
a
Press .
* Press to return to the original screen without
saving.
The machine displays the patterns currently saved.
Note
• Do not turn the main power to OFF while the
“Saving” screen is displayed. You will lose
the pattern you are saving.
Memo
• It takes a few seconds to save a pattern to
the machine’s memory.
• See page E-48 for information on retrieving
a saved pattern.
USING THE MEMORY FUNCTION
E-46
b
Select the pattern you want to delete.
c
Press .
a Amount of memory used by the pattern to be
deleted
b Amount of memory needed to save the current
pattern
d
Press .
* If you decide not to delete the pattern, press .
The “Saving” screen displays. When the pattern is
saved, the display returns to the original screen
automatically.
Saving Embroidery Patterns to
USB Media
When sending embroidery patterns from the
machine to USB media, plug the USB media into
the machine’s USB port.
a
Press when the pattern you want to
save is in the embroidery screen.
Note
• Do not turn the main power to OFF while the
“Saving” screen is displayed. You will lose
the pattern you are saving.
Memo
• If there is enough memory available after
deleting the pattern, the pattern you want to
save will be saved automatically. If there is
not enough memory available after deleting
the pattern, repeat the steps above to
delete another pattern from the machine’s
memory.
• It takes a few seconds to save a pattern.
• See page E-48 for more information about
retrieving saved patterns.
b
a
Memo
• USB media is commercially available, but
some USB media may not be usable with
this machine. Please visit our website for
more details.
• Depending on the type of USB media being
used, either directly plug the USB device
into the machine’s USB port or plug the
USB media Reader/Writer into the
machine’s USB port.
• The USB media can be inserted or removed
at any time except while saving or deleting a
pattern.
USING THE MEMORY FUNCTION
Embroidery
Embroidering E-47
E
1
b
Insert the USB media into the USB port on
the machine.
a USB port
b USB media
c
Press .
* Press to return to the original screen without
saving.
The “Saving” screen is displayed. When the pattern
is saved, the display returns to the original screen
automatically.
Saving Embroidery Patterns in the
Computer
Using the included USB cable, the machine can be
connected to your computer, and the embroidery
patterns can be temporarily retrieved from and
saved in the “Removable Disk” folder in your
computer. A total of about 772KB of embroidery
patterns can be saved in the “Removable Disk”, but
the saved embroidery patterns are deleted when
the machine is turned OFF.
For Computers and Operating Systems, see
“Connecting Your Machine to the Computer” on
page E-44.
a
Plug the USB cable connector into the
corresponding USB ports for the computer
and for the machine.
b
Turn on your computer and select
“Computer (My computer)”.
* The USB cable can be plugged into the USB ports
on the computer and embroidery machine whether
or not they are turned on.
a USB port for computer
b USB cable connector
The “Removable Disk” icon will appear in
“Computer (My computer)” on the computer.
Note
• The processing speed may vary by quantity
of data.
• Do not insert anything other than USB
media into the USB media port. Otherwise,
the USB media drive may be damaged.
Note
• Do not insert or remove USB media while
“Saving” screen is displayed. You will lose
some or all of the pattern you are saving.
Note
• Do not turn the main power to OFF while the
“Saving” screen is displayed. You will lose
the pattern you are saving.
Note
• The connectors on the USB cable can only
be inserted into a port in one direction. If it
is difficult to insert the connector, do not
insert it with force. Check the orientation of
the connector.
• For details on the position of the USB port
on the computer (or USB hub), refer to the
instruction manual for the corresponding
equipment.
USING THE MEMORY FUNCTION
E-48
c
Press when the pattern you want to
save is in the embroidery screen.
d
Press .
* Press to return to the original screen without
saving.
The pattern will be temporarily saved to
“Removable Disk” under “Computer (My
computer)”.
e
Select the pattern’s .phc file in “Removable
Disk” and copy the file to the computer.
Retrieving Patterns from the
Machine’s Memory
a
Press .
The machine displays the patterns currently in the
memory.
b
Press the key of the pattern you want to
retrieve.
* Press to return to the original screen.
c
Press .
The embroidery screen is displayed.
USING THE MEMORY FUNCTION
Embroidery
Embroidering E-49
E
1
Recalling from USB Media
You can recall a specific embroidery pattern from
either direct USB media or a folder in the USB
media. If the pattern is in a folder, check each
folder to find the embroidery pattern.
a
Insert the USB media into the USB port on
the machine (see page E-46).
a USB port
b USB media
b
Press .
Embroidery patterns and a folder in a top folder are
displayed.
c
Press when there is a subfolder to
sort two or more stitch patterns to USB
media, the embroidery pattern in the
subfolder is displayed.
* Press to return to the original screen without
recalling.
a Folder name
b Embroidery patterns in USB media
c Path
* The path to shows the current folder at the top of the
list.
Embroidery patterns and subfolders within a folder
are displayed.
* Press to return to the previous folder.
* Use the computer to create folders. Folders cannot
be created with the machine.
d
Press the key of the pattern you want to
retrieve.
* Press to return to the original screen.
e
Press .
* Press to delete the pattern. The pattern will be
deleted from the USB media.
The embroidery screen is displayed.
Note
• The processing speed may vary by quantity
of data.
a
b
c
USING THE MEMORY FUNCTION
E-50
Recalling from the Computer
For Computers and Operating Systems, see
“Connecting Your Machine to the Computer” on
page E-44.
a
Plug the USB cable connector into the
corresponding USB ports for the computer
and for the machine (see page E-47).
b
On the computer, open “Computer (My
computer)” then go to “Removable Disk”.
c
Move/copy the pattern data to “Removable
Disk”.
Pattern data in “Removable Disk” is written to the
machine.
d
Press .
The patterns in the computer are displayed on the
selection screen.
e
Press the key of the pattern you want to
recall.
* Press to return to the original screen.
f
Press .
The embroidery screen is displayed.
Note
• While data is being written, do not
disconnect the USB cable.
• Do not create folders within “Removable
Disk”. Since folders are not displayed, stitch
pattern data within folders cannot be
recalled.
EMBROIDERY APPLICATIONS
Embroidery
Embroidering E-51
E
1
Using a Frame Pattern to Make
an Appliqué (1)
You can use framed patterns of the same size and
shape to create an appliqué. Embroider one
pattern with a straight stitch and one pattern with a
satin stitch.
a
Select a straight stitch frame pattern.
Embroider the pattern onto the appliqué
material, then cut neatly around the outside
of the shape.
b
Embroider the same pattern from step a
onto the base fabric.
c
Apply a thin layer of fabric glue or a
temporary spray adhesive to the rear of the
appliqué created in step
a. Attach the
appliqué to the base fabric matching the
shapes.
d
Select the satin stitch frame pattern of the
same shape as the appliqué. Embroider over
the appliqué and base fabric from step
c to
create the appliqué.
EMBROIDERY APPLICATIONS
Note
• If you change the size or position of the
patterns when selecting them, make a note
of the size and location.
a Appliqué material
EMBROIDERY APPLICATIONS
E-52
Using a Frame Pattern to Make
an Appliqué (2)
This is a second method to make appliqué using
embroidery patterns. You do not have to change
the fabric in the embroidery frame using this
method. Embroider one pattern with a straight
stitch and one pattern with a satin stitch.
a
Select a straight stitch frame pattern, and
embroider the pattern onto the base fabric.
b
Place the appliqué fabric over the pattern
embroidered in step
a.
* Be sure that the appliqué fabric completely covers
the stitched line.
c
Embroider the same pattern on the appliqué
fabric.
d
Remove the embroidery frame from the
embroidery unit, and cut around the
outside of the stitches.
e
Select the satin stitch frame pattern of the
same shape as the appliqué.
Note
• Do not remove the fabric from the
embroidery frame to cut it. Also, do not pull
or push on the fabric. Otherwise, the fabric
may loosen in the frame.
Note
• Do not change the size or position of the
pattern.
• If you change the size or position of the
patterns when selecting them, make a note
of the size and location.
a Appliqué material
EMBROIDERY APPLICATIONS
Embroidery
Embroidering E-53
E
1
f
Reattach the embroidery frame to the
embroidery unit, and embroider the satin
stitch pattern to create an appliqué.
Sewing Split Embroidery Patterns
Split embroidery patterns created with PE-DESIGN
Ver.7 or later, or PE-DESIGN NEXT can be sewn.
With split embroidery patterns, embroidery
designs larger than the embroidery hoop are
divided into multiple sections, which combine to
create a single pattern after each section is sewn.
For details on creating split embroidery patterns
and for more detailed sewing instructions, refer to
the Instruction manual included with PE-DESIGN
Ver.7 or later, or PE-DESIGN NEXT.
The following procedure describes how to read
the split embroidery pattern shown below from
USB media and embroider it.
a
Connect to the machine the media
containing the created split embroidery
pattern, and then select the split
embroidery pattern to be embroidered.
* For details on recalling patterns, refer to “Selecting
Patterns from Embroidery Cards” on page E-7,
“Recalling from USB Media” on page E-49, or
“Recalling from the Computer” on page E-50.
A screen appears so that a section of the split
embroidery pattern can be selected.
b
Select section to be embroidered.
* Select the sections in alphabetical order.
* A maximum of 12 sections can be displayed in one
page. If there are 13 or more sections in the pattern,
press or to display the previous or next
page.
EMBROIDERY APPLICATIONS
E-54
c
Press .
d
If necessary, edit the pattern.
* For details, refer to “REVISING THE PATTERN” on
page E-36.
e
Press the “Start/Stop” button to embroider
the pattern section.
f
When embroidering is finished, the
following screen appears. Press .
A screen appears so that a section of the split
embroidery pattern can be selected.
g
Repeat steps b through f to embroider
the remaining sections of the pattern.
Memo
• The pattern can be rotated 90° to either the
left or right when is pressed.
EMBROIDERY APPLICATIONS
Embroidery
Embroidering E-55
E
1
Chapter 2
E Embroidering
Embroidery Edit
EXPLANATION OF FUNCTIONS.............................57
SELECTING PATTERNS TO EDIT .............................58
Selecting Embroidery Patterns/Brother “Exclusives”/
Floral Alphabet Patterns/Frame/Bobbin Work Patterns ............59
Selecting Alphabet Character Patterns......................................59
EDITING PATTERNS ................................................61
■ Key Functions........................................................................... 62
Moving the Pattern ..................................................................63
Rotating the Pattern..................................................................63
Changing the Size of the Pattern...............................................63
Deleting the Pattern .................................................................63
Displaying Patterns in the Screen Magnified by 200% .............63
Changing the Configuration of Character Patterns ...................64
Changing Character Spacing .....................................................64
Reducing Character Spacing .....................................................65
Separating Combined Character Patterns .................................65
Changing the Color of Each Alphabet Character in a Pattern ...66
Embroidering Linked Characters ...............................................67
Changing the Thread Color ......................................................67
Creating a Custom Thread Table...............................................68
■ Adding a Color to the Custom Thread Table from the List ....... 69
■ Saving the Custom Thread Table to USB media ....................... 70
■ Recalling the Custom Thread Table data from USB media....... 70
Choosing a Color from the Custom Thread Table .....................71
Designing Repeated Patterns ....................................................72
■ Sewing Repeated Patterns ........................................................ 72
■ Repeating One Element of a Repeated Pattern......................... 74
■ Color Sorting Repeated Patterns .............................................. 75
■ Assigning Thread Marks ........................................................... 75
Embroidering the Pattern Repeatedly .......................................76
Duplicating a Pattern................................................................78
After Editing..............................................................................79
COMBINING PATTERNS.........................................80
Editing Combined Patterns........................................................80
■ Selecting combined embroidery patterns................................. 82
Sewing Combined Patterns .......................................................83
VARIOUS EMBROIDERING FUNCTIONS ...............84
Uninterrupted Embroidering
(Monochrome - Using a Single Color).......................................84
Basting Embroidery...................................................................84
USING THE MEMORY FUNCTION ......................... 85
EXPLANATION OF FUNCTIONS
Embroidery Edit
Embroidering E-57
E
2
With the “Embroidery Edit” functions, you can combine embroidery patterns and character patterns,
change the size of patterns, rotate patterns, and perform many other editing functions. This machine can
perform the 9 functions listed below.
■ Combine Patterns
You can easily create combinations of embroidery patterns, frame patterns, character patterns, patterns from the
machine’s memory, patterns from separately sold embroidery cards, and many other patterns.
■ Move Patterns
Within the 30 cm 18 cm (approx. 12 inches 7 inches) wide embroidery area, you can change the position of
patterns, and check the position on the LCD.
■ Rotate Patterns
You can rotate patterns one degree, ten degrees or ninety degrees at a time.
■ Enlarge or Reduce Patterns
You can make patterns larger or smaller.
• This function is not available for some patterns.
■ Create Mirror Images
You can create horizontal mirror images.
• This function is not available for some patterns.
■ Change Alphabet Character Spacing
You can increase or decrease the spacing between characters in combined patterns.
■ Change Alphabet Character Appearance/Layout
You can change the layout of the characters to a curved line, diagonal, etc. There are 6 choices total.
■ Change the Thread Colors of Patterns
You can change the thread colors of the pattern to your favorite colors.
■ Creating a Repeating Pattern
You can add copies of a pattern to create a pattern that repeats in a vertical or horizontal direction.
EXPLANATION OF FUNCTIONS
SELECTING PATTERNS TO EDIT
E-58
Prepare the machine for embroidery according to the instructions on “BEFORE EMBROIDERING” of
“Basic operations”, and press , then to display the screen below.
a Embroidery patterns
b Brother “Exclusives”
c Floral alphabet patterns
d Frame patterns
e Character patterns
f Bobbin work patterns (see “Appendix”)
g Patterns saved in the machine’s memory (see page E-48)
h Patterns saved in USB media (see page E-49)
i Patterns saved on the computer (see page E-50)
j Press this key to position the embroidery unit for storage.
SELECTING PATTERNS TO EDIT
Memo
• See included “Quick Reference Guide” for more information on each category’s selection screen.
a
c
g
b
d
i
e
j
h
f
SELECTING PATTERNS TO EDIT
Embroidery Edit
Embroidering E-59
E
2
Selecting Embroidery
Patterns/Brother
“Exclusives”/Floral Alphabet
Patterns/Frame/Bobbin Work
Patterns
a
Select the category of the pattern.
* Refer to “How to Create Bobbin Work” of
“Appendix” about the bobbin work patterns.
b
Press the key of the pattern you want to
edit.
* See page E-4 and E-7 for more information on
selecting patterns.
The pattern is displayed in the top part of the screen.
c
Press .
The pattern selected for editing is outlined in red on
the “Embroidery Edit” display.
d
Proceed to “EDITING PATTERNS” on
page E-61 to edit the pattern.
Selecting Alphabet Character
Patterns
When you select character patterns from the
“Embroidery Edit” screen, you can edit the
appearance of the pattern at the same time.
a
Press .
b
Select the font, then enter the characters.
(Example: A B C)
* See page E-5 for more information about selecting
characters.
SELECTING PATTERNS TO EDIT
E-60
c
Press to change the layout of the
pattern.
* If the characters are too small to see, press to
view a display of all entered characters.
d
Select the layout. (Example: )
When selecting an arc, use and to
change the degree of the arc.
* Press to make the arc flatter.
* Press to make the arc rounder.
e
Press to return to the original screen.
f
After you finish your selections, press
.
The “Embroidery Edit” screen will appear.
g
Proceed to “EDITING PATTERNS” on
page E-61 to edit the pattern.
Memo
• When selecting , and
change to and . You can
increase or decrease the incline.
EDITING PATTERNS
Embroidery Edit
Embroidering E-61
E
2
EDITING PATTERNS
a Shows the size of the entire combined pattern.
b Shows the size of the pattern currently selected.
c Shows the distance from the center of the frame.
d Shows the color sequence and times of each step of the pattern currently selected.
e Shows the degree of rotation for the pattern.
Memo
• If a key display is light gray, you cannot use that function with the selected pattern.
b
c
d
e
a
e
d
a
b
c
EDITING PATTERNS
E-62
■ Key Functions
No. Display Key Name Explanation Page
a Magnify key Press this key to magnify the pattern by 200% in the screen. E-63
b Thread palette key Press this key to change the colors of the displayed pattern. E-67
c Rotate key Press this key to rotate the pattern. You can rotate a pattern one degree, ten
degrees or ninety degrees at a time.
E-38
d Size key Press this key to change the size of the pattern. Patterns can be enlarged or
reduced.
E-37
e Array key Press this key to change the configuration of a character pattern. E-64
f Multi color key Press this key to change the color of individual characters in a pattern. E-66
g Character spacing
key
Press this key to change the spacing of character patterns. E-64
h Add key Press this key to add another pattern to the editing pattern. E-79
i Delete key Press this key to delete the selected pattern (the pattern outlined by the red
box).
E-63
j “Embroidery” key Press this key to call up the “Embroidery” screen. E-79
k Pattern select key When a combined pattern is selected, use these keys to select a part of the
pattern to edit.
E-64
l Duplicate key Press this key to duplicate a pattern. E-78
m Density key Press this key to change the density of frame patterns or character patterns. E-40
n Horizontal mirror
image key
Press this key to make a horizontal mirror image of the selected pattern. E-39
o Border key Press this key to make and edit a repeating pattern. E-72
p Arrow keys
( Center key)
Press these keys to move the pattern in the direction indicated by the arrow on
the key. (Press to return the pattern to its original position.)
E-36
b
c
a
e
g
h
i
m
l
j
d
o
n
f
k
p
EDITING PATTERNS
Embroidery Edit
Embroidering E-63
E
2
Moving the Pattern
For details on moving the pattern, refer to “Moving
the Pattern” on page E-36.
Rotating the Pattern
For details on rotating the pattern, refer to
“Rotating the Pattern” on page E-38.
Changing the Size of the Pattern
For details on changing the size of the pattern,
refer to “Changing the Size of the Pattern” on
page E-37.
Deleting the Pattern
Press to delete the pattern from the screen.
Displaying Patterns in the Screen
Magnified by 200%
a
Press .
The pattern is magnified by 200%.
b
Check the displayed pattern.
Use to scroll through the display
in any direction.
c
To display the pattern back to the normal
size (100%), press .
EDITING PATTERNS
E-64
Changing the Configuration of
Character Patterns
a
Press .
b
Press the key of the layout you want to
embroider.
* See page E-60 for more information about layout
types.
The display will show the selected layout.
c
Press .
Changing Character Spacing
a
Press .
b
Use to change the spacing.
* Press to increase the character spacing.
* Press to decrease the character spacing.
* Press to return the pattern to its original
appearance.
c
Press to return to the original screen.
EDITING PATTERNS
Embroidery Edit
Embroidering E-65
E
2
Reducing Character Spacing
The spacing between characters can be reduced to
50% of the narrowest character in the group.
Separating Combined Character
Patterns
Combined character patterns can be separated to
adjust the character spacing or to separately edit
the patterns after all characters have been entered.
a
Press .
b
Press .
The key appears as .
Note
• It is not recommended to edit data and
transfer to other or older version machines.
Same features do not apply in other
machines, so problems may occur.
• Character spacing can be reduced only
when characters are arranged normally on a
straight line.
EDITING PATTERNS
E-66
c
Use to select where the pattern is
to be separated, and then press to
separate it. For this example, the pattern
will be separated between “T” and “a”.
d
Use to select a pattern, and
then use to adjust the character
spacing.
e
Press .
Changing the Color of Each
Alphabet Character in a Pattern
a
Press so you can assign a thread color
to each character.
b
Change the thread to sew each character in
a different color.
* Press to change the colors in the sewing order.
a Color for each character
Note
• A separated character pattern cannot be
combined again.
a
EDITING PATTERNS
Embroidery Edit
Embroidering E-67
E
2
Embroidering Linked Characters
You can embroider linked characters exampled
below, in a single row when the pattern extends
beyond the embroidery frame.
For details on embroidering linked characters,
refer to “Embroidering Linked Characters” on
page E-41.
Example: Linking “DEF” to the characters
“ABC”
Changing the Thread Color
You can change the thread color by moving the
color to be changed to the top of the sewing order
and selecting a new color from the thread colors in
the machine.
a
In the pattern editing screen, press .
The thread color palette screen displays.
b
Press or to put the color you want
to change at the top of the sewing order.
a 64 Embroidery threads table
c
Press to choose a new
color from the color palette.
* To return to the original color, press . If
multiple colors have been changed, this command
will return all colors to their original colors.
* You can select colors from the color palette by
directly touching the color selection with the touch
pen.
a Color palette
The selected color appears at the top of the sewing
order.
d
Press .
The display shows the changed colors.
a
Memo
• To select a color from the Custom Thread
Table, “Choosing a Color from the Custom
Thread Table” on page E-71.
a
EDITING PATTERNS
E-68
Creating a Custom Thread Table
You can create a custom thread table containing
the thread colors that you most often use. You can
select thread colors from the machine’s extensive
list of thread colors from nine different thread
brands. You can select any color and move the
color to your custom thread table.
a
In the pattern editing screen, press and
then press .
b
Use to choose where to
add a color on the custom thread table.
* You can choose colors from the custom thread table
by directly touching the screen with the touch pen.
* You can scroll through 100 colors at a time using
and on the custom thread table.
a Custom thread table
b Press to recall the custom thread table
data (See page E-70)
c
Use to select one of the thread
brands in the machine.
d
Use
to enter a color’s 4-digit number.
* If you make a mistake, press to erase the
entered number, and then enter the correct number.
a Thread brand
Note
• Some machines may already have an
additional 300 Robison-Anton thread colors
contained in the custom thread table. 300
Robison-Anton thread colors table data can
be downloaded from our website
“ http://support.brother.com
”.
a
b
a
EDITING PATTERNS
Embroidery Edit
Embroidering E-69
E
2
e
Press .
a Thread brand
b Entered thread color number
The selected thread color is set in the custom thread
table.
f
Repeat the previous steps until all desired
thread colors are specified.
* To delete a specified color from the palette, select
the color to be deleted, and then press .
* To delete all the specified color from the palette,
press .
g
Press to return to the original screen.
■ Adding a Color to the Custom
Thread Table from the List
a
Repeat the previous steps a through c on
page E-68.
b
Press to display the thread list.
c
Use to select a thread color.
a Thread list
b Thread brand
d
Press .
Note
• If is not pressed, the thread color
number will not be changed.
Note
• You can save the created custom thread
table data. Refer to “Saving the Custom
Thread Table to USB media” on page E-70
for the detailed procedure.
b
a
b
a
EDITING PATTERNS
E-70
e
Repeat the previous steps until all desired
thread colors are specified.
* To delete a specified color from the palette, select
the color to be deleted, and then press .
* To delete all the specified color from the palette,
press .
f
Press to return to the original screen.
■ Saving the Custom Thread Table to
USB media
You can save a custom thread table data file to USB
media.
a
Press and then press .
b
Set your desired colors in the custom thread
table according to the procedure in
“Creating a Custom Thread Table” on
page E-68.
c
Insert the USB media into the USB port on
the machine.
a USB port
b USB media
d
Press .
The “Saving” screen is displayed. When the data is
saved, the display returns to the original screen
automatically.
■ Recalling the Custom Thread Table
data from USB media
You can recall a custom thread table data from USB
media.
a
Insert the USB media containing the custom
thread table data into the USB port.
a USB port
b USB media
Note
• Custom thread table data can only be saved
to USB media. You cannot save the data in
the machine’s memory or in the computer.
• Custom thread table data is saved as “.pcp”
data file.
Note
• Do not insert or remove USB media while
“Saving” screen is displayed. You will lose
some or all of the data you are saving.
Note
• Do not store two or more “.pcp” data file in
USB media. You can only recall one custom
thread table data at a time.
EDITING PATTERNS
Embroidery Edit
Embroidering E-71
E
2
b
Press and then press .
c
Press .
The “Saving” screen is displayed. When the data is
loaded to the machine, the display returns to the
original screen automatically.
d
The recalled custom thread table is
displayed on the screen.
Choosing a Color from the
Custom Thread Table
You can select a color from the up to 300 thread
colors you have set in the custom thread table.
a
Press .
The thread color palette screen displays.
b
Press or to put the color you want
to change at the top of the sewing order.
Note
• Do not insert or remove USB media while
“Saving” screen is displayed. You will lose
some or all of the data you are saving.
EDITING PATTERNS
E-72
c
Press .
a Custom thread change key
The custom thread table will appear.
d
Press to choose a new
color from the custom thread table.
* Use and to scroll through the custom
thread table.
* Press to return to the original color.
* You can choose colors from the custom thread table
by directly touching the screen with the touch pen.
a Custom thread table
The display shows the changed colors.
e
Press .
Designing Repeated Patterns
■ Sewing Repeated Patterns
Using the border function, you can create stitches
using repeated patterns. You can also adjust the
spacing of the patterns within a repeated pattern
stitch.
a
Select a pattern, and then press .
b
Press .
c
Select the direction in which the pattern
will be repeated.
a
a
a
c
e
EDITING PATTERNS
Embroidery Edit
Embroidering E-73
E
2
a Vertical direction
b Horizontal direction
c Repeating and deleting vertical keys
d Repeating and deleting horizontal keys
e Spacing keys
The pattern direction indicator will change
depending on the direction selected.
d
Use to repeat the pattern on top and
to repeat the pattern at the bottom.
* To delete the top pattern, press .
* To delete the bottom pattern, press .
e
Adjust the spacing of the repeated pattern.
* To widen spacing, press .
* To tighten spacing, press .
a Press to change a repeated pattern back to
one single pattern.
f
Complete repeated patterns by repeating
steps
c through e.
g
Press to finish repeating.
b
d
e
Memo
• You can only adjust the spacing of patterns
included in the red frame.
Memo
• When there are two or more patterns, all
patterns will be grouped together as one
pattern in the red frame.
• When changing the direction in which the
pattern will be repeated, all of the patterns
in the red frame will automatically be
grouped as one repeating unit. Press
to change a repeated pattern back to one
single pattern. See the following section on
how to repeat one element of a repeated
pattern.
a
EDITING PATTERNS
E-74
■ Repeating One Element of a
Repeated Pattern
By using the Cut function, you can select one
element of a repeated pattern and repeat only that
single element. This function allows you to design
complex repeated patterns.
a
Choose the direction in which the repeated
pattern will be cut.
* Press to cut horizontally.
* Press to cut vertically.
The pattern direction indicator will change
depending on the direction selected.
b
Use and to select the cut line.
The cut line will move.
c
Press .
The repeated pattern will be divided into separate
elements.
d
Press .
e
Use and to select the element to
repeat.
f
Repeat the selected element.
EDITING PATTERNS
Embroidery Edit
Embroidering E-75
E
2
g
Press to finish repeating.
■ Color Sorting Repeated Patterns
Press to automatically change the sewing
order of colors in combined border embroidery
patterns so that the same color can be continuously
sewn. This allows you to continue sewing without
repeatedly changing the upper thread or changing
the sewing order manually.
■ Assigning Thread Marks
By sewing thread marks, you can easily align
patterns when embroidering a series. When sewing
is finished on a pattern, a thread mark in the shape
of an arrow will be sewn using the final thread.
When sewing a series of patterns, use the point of
this arrow for positioning the following designs to be
sewn.
Note
• Once you have cut a repeated pattern into
separate elements, you cannot return to the
original repeated pattern.
• Each element can be edited separately in
the edit screen. See “Selecting combined
embroidery patterns” on page E-82.
Memo
• In combined stitch patterns that contain two
or more border patterns or other patterns
combined with border patterns, the sewing
order of only the border patterns is
changed.
• When a group of two or more patterns using
border patterns is repeated, the sewing
order is changed so that the same color can
be sewn continuously in each pattern.
Memo
• When repeatedly sewing individual patterns,
thread marks can be sewn around the
perimeter of the pattern only.
EDITING PATTERNS
E-76
a
Press .
b
Press .
c
Press to select the thread mark to be
sewn.
d
Press .
Embroidering the Pattern
Repeatedly
After creating the repeated pattern, rehoop the
embroidery frame and keep sewing for the next
pattern.
Memo
• When there are two or more elements, use
and or and to select a
pattern that you want to assign a thread
mark(s) to.
Memo
• The optional border frame allows you to
easily rehoop the fabric without removing
the embroidery frame from the machine.
EDITING PATTERNS
Embroidery Edit
Embroidering E-77
E
2
a
Create the repeated pattern with the thread
mark at the center of the end of the pattern.
* Refer to “Assigning Thread Marks” on page E-75.
b
Press , then .
c
Press the “Start/Stop” button to begin
embroidering.
When embroidering is finished, the thread mark is
sewn with the last thread color.
d
Remove the embroidery frame.
e
Rehoop the fabric in the embroidery frame.
f
Attach the embroidery frame to the
machine, and then touch .
Note
• Adjust the position of the fabric so that the
embroidering area for the next pattern is
within the embroidering area of the
embroidery sheet.
a Pattern embroidered first
b Position of pattern to be embroidered next
c Embroidering area of embroidery sheet
EDITING PATTERNS
E-78
g
Touch to set the starting point to the
center top of the pattern.
h
Touch .
i
Press the positioning keys to move the
embroidery frame until the starting point is
aligned with the thread mark on the fabric.
a Positioning keys
* Press to check the embroidering position.
j
Remove the thread mark.
k
Press the “Start/Stop” button to begin
embroidering.
Duplicating a Pattern
a
Press .
The duplicate is positioned over the original pattern.
a Duplicated pattern
a
Note
• If multiple patterns are displayed in the
screen, only the pattern selected using
and is duplicated.
• Move and edit each duplicated pattern
individually.
a
EDITING PATTERNS
Embroidery Edit
Embroidering E-79
E
2
After Editing
a
Press .
* To combine the pattern with other patterns, select
(see page E-80).
* See page E-21 for more information about sewing
patterns.
Memo
• If you want to return to the edit screen after
pressing , press .
COMBINING PATTERNS
E-80
Editing Combined Patterns
Example: Combining alphabet characters
with an embroidery pattern and
editing
a
Press to select an embroidery
pattern.
b
Select .
c
Press .
COMBINING PATTERNS
COMBINING PATTERNS
Embroidery Edit
Embroidering E-81
E
2
d
Press .
e
Press to enter the alphabet
characters.
* Press to return to the previous screen.
f
Select and enter “Flower”.
* After selecting , press to change the
character case, then enter the remaining characters.
The characters you enter will be displayed in the
center of the display.
g
Press .
h
Use to move the characters.
* With a USB mouse, your finger or the touch pen,
drag the characters to move them.
i
Press to change the layout of the
characters. Press .
* See page E-64 for more information about changing
the layout.
COMBINING PATTERNS
E-82
j
Press to change the color of the
characters.
* See page E-67 for more information about changing
the color.
k
When all editing is finished, press .
■ Selecting combined embroidery
patterns
If multiple patterns have been combined, use
to select the pattern to be edited. If a
USB mouse is connected, the pattern can be
selected by clicking it. Move the mouse to position
the pointer over the desired pattern, and then click
the left mouse button. In addition, patterns can be
selected by directly touching the screen with your
finger or touch pen.
Memo
• Use to select patterns that are
overlapping and cannot be selected by
clicking them or by touching the screen.
COMBINING PATTERNS
Embroidery Edit
Embroidering E-83
E
2
Sewing Combined Patterns
Combined patterns will be embroidered in the
order they were entered. In this example, the
embroidery order will be as follows:
a
Embroider by following the
color order on the right side of the display.
After the flowers are embroidered, the [+] cursor
will move to the “Flower” part of the pattern.
b
Embroider .
Note
• Follow the directions in “Sewing Embroidery
Patterns” on page E-22.
VARIOUS EMBROIDERING FUNCTIONS
E-84
Uninterrupted Embroidering
(Monochrome - Using a Single
Color)
A selected pattern can be stitched out in one color
instead of multicolor. The machine will hesitate
but not stop between color steps, and then
continue till the pattern is completed. Press
for the multicolor steps to become shaded and the
selected pattern will embroider in a single color,
instead of changing the thread while
embroidering. Press again to return to the
pattern’s original settings.
Basting Embroidery
Before embroidering, basting stitches can be sewn
along the outline of the pattern. This is useful for
embroidering fabric that cannot have stabilizer
material affixed with an iron or adhesive. By
stitching stabilizer material to the fabric, shrinkage
of the stitching or misaligned pattern can be
minimized.
a
Press .
b
In the “Embroidery Basting Distance”
display, use and to specify the
distance from the pattern to the basting
stitching.
c
Press to return to the previous
screen.
d
Press .
e
Press to select the basting setting.
VARIOUS EMBROIDERING FUNCTIONS
Note
• It is recommended to finish combining and
editing the pattern before selecting the
basting setting. If the pattern is edited after
selecting the basting setting, the basting
and pattern may become misaligned, and
the basting under the pattern may be
difficult to remove after embroidering is
complete.
Memo
• The higher the setting, the farther the
basting is from the pattern.
• The setting remains selected even if the
machine is turned off.
Note
• When is pressed, the pattern is moved
to the center. After selecting the basting
setting, move the pattern to the desired
position.
USING THE MEMORY FUNCTION
Embroidery Edit
Embroidering E-85
E
2
Basting is added to the beginning of the sewing
order.
f
Press the “Start/Stop” button to begin
embroidering.
g
When embroidering is finished, remove the
basting stitching.
In the same way as embroidery patterns in Chapter 1, you can save and retrieve edited embroidery
patterns to and from the machine’s memory, a personal computer, or USB media. Refer to the relevant
sections in Chapter 1 on saving and retrieving embroidery patterns and follow the same procedures in
order to save and retrieve edited embroidery patterns.
See page E-44 for more information about the memory function.
Memo
• To cancel the setting, press .
USING THE MEMORY FUNCTION
USING THE MEMORY FUNCTION
E-86
Appendix
This section provides important information for operating this machine. Please read this
section to find troubleshooting tips and pointers as well as how to keep your machine in the
best working order.
Page number starts with “A” in this section.
The screen display and machine illustration may vary slightly, depending on the countries or
regions.
Chapter1 How to Create Bobbin Work ................................. A-2
Chapter2 Maintenance and Troubleshooting....................... A-14
Chapter 1
A Appendix
How to Create Bobbin Work
ABOUT BOBBIN WORK............................................3
PREPARING FOR BOBBIN WORK.............................3
Required Materials......................................................................3
■ Bobbin case and bobbin cover (option)...................................... 3
■ Lower thread.............................................................................. 3
■ Upper thread ............................................................................. 4
■ Needle ....................................................................................... 4
■ Embroidery foot ......................................................................... 4
■ Fabric......................................................................................... 4
Upper Threading.........................................................................4
Preparing the Bobbin Thread ......................................................4
■ When tension is applied to the bobbin thread............................ 6
■ When tension is not applied to the bobbin thread ..................... 6
CREATING BOBBIN WORK ......................................8
Selecting the Pattern...................................................................8
Start Embroidering....................................................................10
ADJUSTING THE THREAD TENSION......................12
■ Adjusting the upper thread tension .......................................... 12
■ Adjusting the tension of the bobbin thread .............................. 12
TROUBLESHOOTING .............................................13
■ The thread was accidentally cut automatically and the bobbin
thread is caught inside the machine......................................... 13
■ Correcting bobbin work tension .............................................. 13
■ The bobbin thread catches on the tension spring
of the bobbin case.................................................................... 13
Included accessories vary depending on the countries or regions.
ABOUT BOBBIN WORK
How to Create Bobbin Work
Appendix A-3
A
1
Beautiful embroidery work, with a three-dimensional appearance, can be created by winding the bobbin
with medium to heavy weight thread or ribbon, which is too thick to be threaded through the machine’s
needle. The decorative thread or ribbon will stitch out on the underneath side of fabric while
embroidering with the fabric wrong side facing up. Bobbin work embroidery is created using the bobbin
work patterns included with this machine.
Refer to the “Quick Reference Guide” about the bobbin work patterns.
Required Materials
■ Bobbin case and bobbin cover
(option)
a Bobbin case (gray)
There is a notch at the location indicated by the
letter “A”.
a Bobbin cover
There are two small v-shaped tabs on the back of
the bobbin cover as indicated by the letter “B”.
The tabs help hold the bobbin in place so it does
not lift up while thick thread is being pulled
through.
■ Lower thread
We recommend the following types of threads for
bobbin work.
* When wide ribbon or heavy weight threads are being used, we
recommend test embroidering with and without bobbin case
tension being applied to see which gives the best results. If
wide ribbon such as 3.5mm (approx. 1/8 inch) is to be used,
we recommend that bobbin case tension not be applied. Refer
to page A-6 for more detailed instructions.
ABOUT BOBBIN WORK
PREPARING FOR BOBBIN WORK
No.5 or finer hand embroidery
thread or decorative thread
Flexible woven ribbon
(Approx. 2mm (approx. 5/64 inch) is
recommended.)
Note
• Do not use thread heavier than No.5 hand
embroidery thread.
• Some threads may not be appropriate for
bobbin work. Be sure to embroider trial
patterns before sewing on your project.
PREPARING FOR BOBBIN WORK
A-4
■ Upper thread
Embroidery thread (polyester thread) or
monofilament (transparent nylon) thread.
If you do not wish for the upper thread to be visible,
we recommend using transparent nylon
monofilament thread or polyester light weight
thread (50wt. or above) that is the same color as the
lower thread.
■ Needle
Use a needle appropriate for the upper thread and
fabric being used. Refer to “Embroidery Step by
Step” on page B-46.
■ Embroidery foot
Embroidery foot “W” or embroidery foot with LED
pointer “W+”
* Included accessories vary depending on the
countries or regions.
■ Fabric
Be sure to embroider trial patterns on a piece of
scrap fabric, which includes the same threads and
fabric as what is being used in your project.
Upper Threading
a
Install a needle appropriate for the upper
thread and fabric to be used.
For details on installing the needle, refer to
“CHANGING THE NEEDLE” on page B-45.
b
Attach the embroidery foot.
c
Thread the machine with the upper thread.
For details on threading the machine, refer to
“Upper Threading” on page B-38.
Preparing the Bobbin Thread
In order to create bobbin work, the bobbin case
must be replaced with the one for bobbin work.
Before creating bobbin work, clean the bobbin case
and the race.
a
Raise the needle and embroidery foot, and
then turn off the machine.
b
Remove the embroidery unit.
c
Grasp both sides of the needle plate cover,
and then slide it toward you to remove it.
a Needle plate cover
d
Remove the bobbin case.
a Bobbin case
e
Use the cleaning brush included with the
machine or a vacuum cleaner to remove
any lint and dust from the race and its
surrounding area.
a Cleaning brush
b Race
Note
• The results may be affected by the type of
fabric used. Before embroidering your
project, be sure to embroider trial patterns
on a piece of scrap fabric that is the same
as the fabric used in the project.
PREPARING FOR BOBBIN WORK
How to Create Bobbin Work
Appendix A-5
A
1
f
Wipe the bobbin case (gray) with a soft lint
free cloth to clean it.
g
Insert the bobbin case so that the mark
on the bobbin case aligns with the ● mark
on the machine.
* Align the and ● marks.
a mark on the bobbin case
b ● mark on the machine
c Bobbin case
h
Wind a decorative thread around the
bobbin by hand. After winding the bobbin
so it is filled as shown below (about 80%),
cut the thread.
For precautions on winding the bobbin for
embroidering, refer to step
b of “Selecting the
Pattern” on page A-8.
i
Using scissors carefully trim the thread tail
as close to the bobbin as possible.
a Beginning of wound thread
Note
• The bobbin case (gray) cannot be used in
any way other than bobbin work. After
creating bobbin work, refer back to the
steps in “Preparing the Bobbin Thread” on
page A-4 for removing and cleaning the
bobbin case (gray), and then reinstall the
standard bobbin case.
CAUTION
• Be sure to use the bobbin case (gray) when
creating bobbin work. Using any other bobbin
case may result in the thread becoming
tangled or damage to the machine.
• Make sure that the bobbin case is correctly
installed. If the bobbin case is incorrectly
installed, the thread may become tangled or
the machine may be damaged.
a
b
b
a
CAUTION
• Be sure to use the machine’s included bobbin
or one designed specifically for this machine.
Using any other bobbin may result in damage
or injuries.
* Actual size
a This model
b Other models
c 11.5 mm (approx. 7/16 inch)
Note
• Slowly and evenly wind the thread around
the bobbin.
• For best results, wind the bobbin so the
thread is snug and not twisted.
CAUTION
• If thread extends beyond the top of the bobbin
too much, the thread may become tangled or
the needle may break.
PREPARING FOR BOBBIN WORK
A-6
j
Install the bobbin wound with thread.
Whether or not tension should be applied to the
bobbin thread depends on the type of thread being
used.
■ When tension is applied to the
bobbin thread
Insert bobbin into bobbin case so the thread
unwinds from the left side.
Then correctly pass the thread through the tension
spring as shown below.
a Tension spring
■ When tension is not applied to the
bobbin thread
If the bobbin thread in the trial pattern is too tight
and adjusting the bobbin case tension does not help,
do not pass the thread through the tension spring.
Hold the bobbin with your left hand so the thread
unwinds from the right side and hold the end of the
thread with your right hand.
k
Pull out about 8 cm (approx. 3 inches) of
bobbin thread.
l
Lightly hold the end of the upper thread
while turning the handwheel toward you
(counterclockwise) until the mark on the
handwheel aligns with the center top of
machine.
CAUTION
• When winding the bobbin, make sure the
thread is not frayed. Embroidering with frayed
thread may result in the thread catching on
the tension spring of the bobbin case, the
thread completely becoming tangled or
damage to the machine.
• Do not guide the bobbin thread through the
groove in the needle plate cover, otherwise
the lower threading cannot be done correctly.
PREPARING FOR BOBBIN WORK
How to Create Bobbin Work
Appendix A-7
A
1
m
Gently pull the upper thread to bring the
bobbin thread up through the needle plate.
A loop of the bobbin thread comes out through the
hole in the needle plate.
n
Insert tweezers through bobbin thread loop
and pull bobbin thread above the needle
plate.
o
Align the upper thread and bobbin thread,
and then pull out about 10 cm (approx.
4 inches) of the threads and pass them
under the presser foot toward the rear of
the machine.
p
Install the needle plate cover and bobbin
cover with tabs.
For details on installing the needle plate cover, refer to
“Cleaning the Race” on page A-15.
a Bobbin cover
b Bobbin cover with tabs
q
Install the embroidery unit.
This completes the upper and lower threading.
CAUTION
• When creating bobbin work, use the bobbin
cover with tabs, otherwise the thread may
become tangled or the needle may break.
Note
• When installing the needle plate cover, do
not allow it to pinch the thread.
Note
• When installing the embroidery unit, do not
allow it to pinch the thread.
• When the bobbin thread is replaced with a
new one, be sure to repeat the procedure
from
a, otherwise the lower threading will
not be done correctly.
CREATING BOBBIN WORK
A-8
Selecting the Pattern
a
Attach the embroidery foot and the
embroidery unit.
b
Install a bobbin wound with an adequate
amount of thread for pattern.
c
Pull up the bobbin thread above the needle
plate.
d
Turn on the machine.
e
Press .
The carriage will move to the initialization position.
f
To select a bobbin work embroidery
pattern, press (Embroidery).
g
Press , then select one of the bobbin
work embroidery patterns.
Embroidery patterns for bobbin work appear with
the letter “B” in the lower-left corner of the key.
a “B” mark
Regardless of the setting that had been selected, the
automatic thread cutting function is turned off.
When a bobbin work embroidery pattern is selected
the embroidery sewing speed can only be adjusted
from 100 spm to a maximum of 350 spm.
CREATING BOBBIN WORK
Note
• Prepare the machine for bobbin work as
described in “PREPARING FOR BOBBIN
WORK” on page A-3.
Note
• For an estimated length of bobbin thread
required for each pattern, refer to the
“Quick Reference Guide” included with the
machine. Be sure to use a bobbin wound
with enough thread. If the bobbin runs out
of thread while sewing, the embroidery
cannot be completed.
• Depending on the thread thickness, it may
not be possible to wind the bobbin with the
necessary length of thread. In this case, try
winding the bobbin again, or use a lighter
weight thread.
Note
• Embroidery patterns for bobbin work “B”
cannot be used in the “Embroidery Edit”
screen ( ).
Note
• The beginning and end of stitching are
specified for bobbin work patterns. They
cannot be used for normal embroidering.
• Recommended default setting for bobbin
work embroidery is 100 spm.
a
CREATING BOBBIN WORK
How to Create Bobbin Work
Appendix A-9
A
1
h
Press .
The sewing screen is displayed.
i
Press , and then adjust the tension of
the upper thread.
For details on adjusting the tension of the upper
thread, refer to “Adjusting Thread Tension” on
page E-30.
CAUTION
• When sewing bobbin work, be sure to select an
embroidery pattern for bobbin work. If any other
type of pattern is selected, the machine may be
damaged.
Note
• Bobbin work embroidery sewing speed
defaults to 100 spm when a bobbin work
embroidery pattern is selected. The
Settings screen will only allow speed to be
adjusted from 100 spm to a maximum
sewing speed of 350 spm.
Memo
• When an embroidery pattern for bobbin
work is selected, the automatic thread
cutting function is turned off. Afterward, if a
pattern other than one for bobbin work is
selected, the automatic thread cutting
function is returned to the setting that was
selected before the embroidery pattern for
bobbin work was chosen.
Note
• Since bobbin work is sewn from the wrong
side of the fabric, the pattern shown in the
screen appears as a mirror image of the
final sewn embroidery. If necessary, flip the
image to preview it. In addition, when
sewing with the thread colors shown in the
embroidery screen, select a bobbin thread
that matches what is shown in the screen.
a Image shown in screen b Sewn embroidery
(Right side of fabric)
Memo
• With embroidery patterns for bobbin work,
the size and thread density cannot be
changed. In addition, the automatic thread
cutting function cannot be turned on.
Memo
• We recommend a setting between 6 and 8
for the upper thread tension.
CREATING BOBBIN WORK
A-10
Start Embroidering
a
Hoop the fabric so the right side of the
fabric is facing down with the stabilizer
lying on the top. Use an embroidery frame
that fits the size of the pattern and then
attach the frame to the machine. These
patterns are embroidered from the wrong
side of the fabric so technically you are
working in “reverse” of normal
embroidering.
a Wrong side of fabric
b
It is necessary to move to the beginning of
stitching so press , and then press .
The embroidery frame moves to the beginning of
stitching.
c
Press .
d
Press .
The screen changes, and all keys and operation
buttons are locked.
e
Using the presser foot lever, raise the
presser foot.
f
To bring the bobbin thread above the
fabric, rotate the handwheel
counterclockwise while holding the upper
thread.
g
As shown below, pull the upper thread to
pull the bobbin thread up through the
fabric.
a Upper thread
b Bobbin thread
h
Press to unlock all keys and
buttons.
i
Lower the presser foot.
j
While holding both the upper thread and
the bobbin thread, sew a section of the
pattern.
CAUTION
• Always use a stabilizer material for embroidery.
Otherwise, the needle may break and cause injuries.
Not using a stabilizer material may result in a poor
finish to your project.
Memo
• If the bobbin thread cannot be pulled up,
use an awl to create small hole to help pull
bobbin thread to surface.
CREATING BOBBIN WORK
How to Create Bobbin Work
Appendix A-11
A
1
k
Stop the machine, and then tie the upper
thread and the bobbin thread together to
secure the threads.
l
Start sewing again to finish the pattern.
m
Raise the needle and presser foot, remove
the embroidery frame, and then cut the
upper thread and the bobbin thread.
When cutting the threads, be sure to leave an
adequate length of thread so they can be
properly secured.
n
Using a hand sewing needle such as a
ribbon embroidering needle, pull the
bobbin thread to the top (wrong side) of the
fabric, and then tie the upper thread and
the bobbin thread together.
o
Remove the fabric from the embroidery
frame, and check the finished embroidery.
p
If the desired results could not be achieved,
adjust the tension of the bobbin thread and
the upper thread, and then try sewing the
pattern again.
For more details, refer to “ADJUSTING THE THREAD
TENSION” on page A-12.
Memo
• If there is a gap between the start point and
end point of the pattern, leave an adequate
length of thread, cut the threads, and
remove the fabric from the machine. Use a
ribbon embroidering needle to hand sew
stitches to connect the starting and ending
points.
a Right side of fabric b Wrong side of fabric
Memo
• Check bobbin after each bobbin work
embroidery pattern is sewn to make sure
there is adequate bobbin thread for the next
pattern.
• While selecting the bobbin work pattern, the
embroidery speed value is set to “100
spm”. Refer to “Adjusting the Embroidery
Speed” on page E-33 to change the
embroidery speed.
ADJUSTING THE THREAD TENSION
A-12
After embroidering trial patterns and checking the results, adjust the thread tensions if necessary. After adjusting the
tensions, be sure to embroider trial patterns again in order to check the results.
■ Adjusting the upper thread tension
We recommend a setting between 6 and 8 for the upper
thread tension when creating bobbin work.
Refer to “Adjusting Thread Tension” on page E-30.
■ Adjusting the tension of the bobbin
thread
If the desired stitching cannot be achieved after
adjusting the upper thread tension, adjust the tension of
the bobbin thread. The tension of the bobbin thread can
be adjusted by turning the slotted-head (–) screw on the
bobbin case (gray) for bobbin work.
a Do not turn the phillips screw (+).
b Adjust with a small screwdriver.
To increase the tension of the bobbin thread, turn the
slotted-head (–) screw 30° to 45° clockwise.
To decrease the tension of the bobbin thread, turn the
slotted-head (–) screw 30° to 45° counterclockwise.
ADJUSTING THE THREAD TENSION
Note
• Turning the screw on the bobbin case (gray)
may push up the spring plate, as shown
below.
If this occurs, gently press down the spring
plate with a screwdriver so it is lower than
the top surface of the bobbin case (gray),
and then insert the bobbin case into the
machine.
a Spring plate
CAUTION
• DO NOT adjust the position of the phillips (+)
screw on the bobbin case (gray) as this may result in
damage to the bobbin case, rendering it useless.
• If the slotted-head screw (-) is difficult to turn, do
not use force. Turning the screw too much or
providing force in either (rotational) direction may
cause damage to the bobbin case. Should damage
occur, the bobbin case may not maintain proper
tension.
Note
• If the bobbin thread tension is tight, the
thread cannot be passed through the
tension spring when the bobbin is installed
in the bobbin case. (Refer to “When tension
is not applied to the bobbin thread” on
page A-6.)
TROUBLESHOOTING
How to Create Bobbin Work
Appendix A-13
A
1
Several solutions for minor problems are described below. If the problem persists, contact your dealer or nearest
authorized Brother dealer.
■ The thread was accidentally cut
automatically and the bobbin thread
is caught inside the machine
a
Remove the embroidery frame.
b
Cut the thread near the fabric above the
needle plate, and then remove the fabric.
c
Remove the bobbin, and then hold it out
toward the left side of the machine.
d
Lower the embroidery foot.
e
Apply slight tension on bobbin thread by
holding thread out to the left side of presser
foot. Press the “Thread Cutter” button
again.
■ Correcting bobbin work tension
* If the top thread shows on the bobbin side of the
fabric, increase the upper tension (Refer to
“ADJUSTING THE THREAD TENSION” on
page A-12).
* If the top thread still shows on the bobbin side of the
fabric, reduce the tension of the bobbin thread or
bypass the bobbin tension. (Refer to “ADJUSTING
THE THREAD TENSION” on page A-12.)
* Some bobbin threads are too coarse to pass through
to wrong side of fabric. In this case, be sure to color
match top thread with bobbin threads.
Example: Embroidery patterns for bobbin work
a Correct tension
b The upper thread tension is too loose, or the
bobbin thread tension is too tight.
■ The bobbin thread catches on the
tension spring of the bobbin case
Embroider with no tension applied to the bobbin
thread. (Refer to “When tension is not applied to the
bobbin thread” on page A-6.)
TROUBLESHOOTING
CAUTION
• Do not pull on the thread with excessive force,
otherwise the machine may be damaged.
Chapter 2
A Appendix
Maintenance and Troubleshooting
CARE AND MAINTENANCE ....................................15
Restrictions on oiling ................................................................15
Precautions on storing the machine ..........................................15
Cleaning the LCD Screen .........................................................15
Cleaning the Machine Casing ...................................................15
Cleaning the Race .....................................................................15
Cleaning the Cutter in the Bobbin Case Area............................17
About the Maintenance Message ..............................................17
ADJUSTING THE SCREEN .......................................18
Adjusting the Brightness of the Screen Display .........................18
Touch Panel is Malfunctioning..................................................18
TROUBLESHOOTING .............................................19
ERROR MESSAGES...................................................22
SPECIFICATIONS.....................................................25
UPGRADING YOUR MACHINE’S SOFTWARE........26
Upgrade Procedure Using USB Media ......................................26
Upgrade Procedure Using Computer ........................................27
INDEX......................................................................28
CARE AND MAINTENANCE
Maintenance and Troubleshooting
Appendix A-15
A
2
Restrictions on oiling
In order to prevent damaging this machine, it must
not be oiled by the user. This machine was
manufactured with the necessary amount of oil
applied to ensure correct operation, making
periodic oiling unnecessary.
If problems occur, such as difficulty turning the
handwheel or an unusual noise, immediately stop
using the machine, and contact your authorized
dealer or the nearest authorized service center.
Precautions on storing the
machine
Do not store the machine in any of the locations
described below, otherwise damage to the
machine may result, for example, rust caused by
condensation.
* Exposed to extremely high temperatures
* Exposed to extremely low temperatures
* Exposed to extreme temperature changes
* Exposed to high humidity or steam
* Near a flame, heater or air conditioner
* Outdoors or exposed to direct sunlight
* Exposed to extremely dusty or oily environments
Cleaning the LCD Screen
If the screen is dirty, gently wipe it with a soft, dry
cloth. Do not use organic solvents or detergents.
Cleaning the Machine Casing
If the surface of the machine is dirty, lightly soak a
cloth in a neutral detergent, squeeze it out firmly,
and then wipe the surface. Then wipe again with a
dry cloth.
Cleaning the Race
If dust or bits of dirt collect in the race or bobbin
case, the machine will not run well, and the
bobbin thread detection function may not operate.
Keep the machine clean for best results.
a
Press the “Needle Position” button to raise
the needle.
b
Turn the main power to OFF.
c
Remove the needle and embroidery foot
(see page B-42 through B-45).
d
Remove the embroidery unit if it is
attached.
e
Grasp both sides of the needle plate cover,
and then slide it toward you.
a Needle plate cover
The needle plate cover is removed.
f
Grasp the bobbin case, and then pull it out.
a Bobbin case
CARE AND MAINTENANCE
CAUTION
• Be sure to unplug the machine before cleaning it. Otherwise, electric shock or injury may result.
Note
• In order to extend the life of this machine,
periodically turn it on and use it. Storing this
machine for an extended period of time
without using it may reduce its efficiency.
Note
• Do not wipe the LCD screen with a damp
cloth.
Memo
• Occasionally, condensation may form on
the LCD screen or it may become fogged
up; however, this is not a malfunction. After
a while, the cloudiness will disappear.
CARE AND MAINTENANCE
A-16
g
Use the cleaning brush or a vacuum cleaner
to remove any lint and dust from the race
and bobbin thread sensor and the
surrounding area.
a Cleaning brush
b Race
c Bobbin thread sensor
h
Insert the bobbin case so that the mark
on the bobbin case aligns with the ● mark
on the machine.
* Align the and ● marks.
a mark on the bobbin case
b ● mark on the machine
c Bobbin case
* Make sure that the indicated points are aligned
before installing the bobbin case.
i
Insert the tabs on the needle plate cover
into the needle plate, and then slide the
cover back on.
Note
• Do not apply oil to the bobbin case.
• If lint or dust collects on the bobbin thread
sensor, the sensor may not operate
correctly.
a
b
b
a
CAUTION
• Never use a bobbin case that is scratched;
otherwise, the upper thread may become
tangled, the needle may break, or sewing
performance may suffer. For a new bobbin
case (part code: XC8167-551 (no color on the
screw), XE8298-001 (gray, for bobbin work)),
contact your dealer or nearest authorized
dealer.
• Make sure that you fit the bobbin case
properly, otherwise the needle may break.
Note
• If the needle plate has been removed it is
especially important to reinstall the needle
plate and tighten the screws prior to
installing the bobbin case.
CARE AND MAINTENANCE
Maintenance and Troubleshooting
Appendix A-17
A
2
Cleaning the Cutter in the Bobbin
Case Area
The cutter below the needle plate should be
cleaned. If dust or lint accumulate on the cutter, it
will be difficult to cut the thread when the “Thread
Cutter” button is pressed or the automatic thread
cutting function is used. Clean the cutter when the
thread is not easily cut.
a
Follow steps a through e in “Cleaning the
Race” on page A-15 to remove the needle
plate cover.
b
Use the screwdriver included with the
machine to unscrew and remove the needle
plate.
c
Use the cleaning brush or a vacuum cleaner
to remove any lint and dust from the cutter
in the bobbin case area.
a Cutter
d
Use the screwdriver included with the
machine to screw and attach the needle
plate.
e
Insert the tabs on the needle plate cover
into the needle plate, and then slide the
cover back on.
About the Maintenance Message
Once this message appears, it is recommended to
take your machine to an authorized dealer or
nearest authorized service center for a regular
maintenance check. Although this message will
disappear and the machine will continue to
function once you press , the message will
display several more times until the appropriate
maintenance is performed.
Please take the time to arrange the maintenance
your machine requires once this message appears.
Such steps will help to ensure you receive
continued, uninterrupted hours of machine
operation for the future.
CAUTION
• Do not touch the cutter, otherwise injuries
may result.
ADJUSTING THE SCREEN
A-18
Adjusting the Brightness of the
Screen Display
If the screen does not look very clear under certain
situation, you can adjust the brightness of the
screen display.
a
Press .
The settings screen appears.
b
Display page 3 of the settings screen.
c
Press or to adjust the brightness of
the screen display.
* The screen appears dim as the number on the
settings screen decreases. The screen appears
brighter as the number increases.
Touch Panel is Malfunctioning
If the screen does not respond correctly when you
touch a key (the machine does not perform the
operation or performs a different operation), follow
the steps below to make the proper adjustments.
a
Holding your finger on the screen, turn the
main power switch to OFF and back to ON.
The touch panel adjustment screen is displayed.
b
Using the included touch pen, lightly touch
the center of each +, in order from 1 to 5.
c
Turn the main power to OFF, then turn it
back to ON.
ADJUSTING THE SCREEN
Note
• Only use the included touch pen to touch
the screen. Do not use a mechanical pencil,
pin, or other sharp object. Do not press too
hard on the screen. Otherwise, damage
may result.
Note
• If you finish the screen adjustment and the
screen still does not respond, or if you
cannot do the adjustment, contact your
authorized dealer.
+1
+4
+2
+5
+3
TROUBLESHOOTING
Maintenance and Troubleshooting
Appendix A-19
A
2
If the machine stops operating correctly, check the following possible problems before requesting service.
You can solve most problems by yourself. If you need additional help, the Brother Solutions Center offers
the latest FAQs and troubleshooting tips. Visit us at “ http://support.brother.com/
”.
If the problem persists, contact your dealer or the nearest authorized service center.
TROUBLESHOOTING
Problem Cause Solution Page
The thread is tangled
on the wrong side of
the fabric.
Upper threading is incorrect. Check the steps for threading the machine
and rethread the machine.
B-38
Using improper needle or thread for the
selected fabric.
Check the information about the needle and
thread to be used.
B-46, E-21
The upper thread is
too tight.
The bobbin thread is incorrectly installed. Correctly install the bobbin thread. B-36
Cannot thread the
needle
Needle is not in the correct position. Press the “Needle Position” button to raise
the needle.
B-10
Needle is installed incorrectly. Reinstall the needle correctly. B-45
Needle is turned, bent or the point is dull. Replace the needle. B-45
Cannot lower the
presser foot with the
presser foot lever
Presser foot was raised using the “Presser Foot
Lifter” button.
Press the “Presser Foot Lifter” button to
lower the presser foot.
B-10
Thread tension is
incorrect
Upper threading is incorrect. Check the steps for threading the machine
and rethread the machine.
B-38
Bobbin is set incorrectly. Reset the bobbin. (If needle plate was
removed, reinstall needle plate and tighten
screws prior to installing bobbin case.)
B-36
Using improper needle or thread for the
selected fabric.
Check the information about the needle and
thread to be used.
B-46, E-21
Embroidery foot is not attached correctly. Reattach the embroidery foot correctly. B-42
Thread tension is set incorrectly. Adjust the thread tension. E-30
Bobbin thread is incorrectly wound. Use a correctly wound bobbin. B-31
Needle is turned, bent or the point is dull. Replace the needle. B-45
Upper thread breaks Machine is not threaded correctly (used the
wrong spool cap, spool cap is loose, the thread
did not catch the needle bar threader, etc.)
Rethread the machine correctly. B-38
Needle is turned, bent or the point is dull. Replace the needle. B-45
There are scratches on the bobbin case. Replace the bobbin case, or consult your
authorized dealer.
A-15
Upper thread tension is too strong. Adjust the thread tension. E-30
Using improper needle or thread for the
selected fabric.
Check the information about the needle and
thread to be used.
B-46, E-21
Thread is twisted. Use scissors, etc., to cut the twisted thread
and remove it from the race, etc.
—
There are scratches near the hole in the presser
foot.
Replace the presser foot, or consult your
authorized dealer.
B-42
Needle is installed incorrectly. Reinstall the needle correctly. B-45
Thread is knotted or tangled. Rethread upper and lower thread. B-36, B-38
A bobbin designed specifically for this machine
is not used.
Incorrect bobbins will not work properly. Only
use a bobbin designed specifically for this
machine.
B-36
Bobbin thread breaks Bobbin is set incorrectly. Reset the bobbin thread correctly. B-36
There are scratches on the bobbin or it doesn’t
rotate properly.
Replace the bobbin. B-36
Thread is twisted. Use scissors, etc. to cut the twisted thread
and remove it from the race, etc.
—
A bobbin designed specifically for this machine
is not used.
Incorrect bobbins will not work properly. Only
use a bobbin designed specifically for this
machine.
B-36
TROUBLESHOOTING
A-20
Bobbin thread does
not wind neatly on the
bobbin.
The thread is not passed through the bobbin
winding thread guide correctly.
Correctly pass the thread through the bobbin
winding thread guide.
B-32
Bobbin spins slowly. Press [+] in the bobbin winding window to
increase the bobbin winding speed.
B-34
The thread that was pulled out was not wound
onto the bobbin correctly.
Wind the thread that was pulled off around
the bobbin 5 or 6 times clockwise.
B-33
Skipped stitches Needle is turned, bent or the point is dull. Replace the needle. B-45
Using improper needle or thread for the
selected fabric.
Check the information about the needle and
thread to be used.
B-46, E-21
Machine is threaded incorrectly. Check the steps for threading the machine
and rethread it correctly.
B-38
Dust or lint has collected under the needle
plate.
Remove the dust or lint with the brush. A-15
Needle is installed incorrectly. Reinstall the needle correctly. B-45
Needle is defective. Replace the needle. B-45
Needle breaks Needle is installed incorrectly. Reinstall the needle correctly. B-45
Needle clamp screw is not tightened. Tighten the needle clamp screw. B-45
Needle is turned or bent. Replace the needle. B-45
Using improper needle or thread for the
selected fabric.
Check the needle and fabric combination. B-46, E-21
Upper thread tension is too strong. Adjust the thread tension setting. E-30
Fabric is pulled during sewing. Do not pull the fabric during sewing. —
Spool cap is set incorrectly. Check the method for attaching the spool
cap, then reattach the spool cap.
B-38
There are scratches around the hole(s) in the
embroidery foot.
Replace the embroidery foot, or consult your
authorized dealer.
B-42
There are scratches on the bobbin case. Replace the bobbin case, or consult your
authorized dealer.
A-15
Needle is defective. Replace the needle. B-45
Upper threading is incorrect. Check the steps for threading the machine
and rethread the machine.
B-38
Bobbin is set incorrectly. Reset the bobbin thread correctly. B-36
Embroidery foot is attached incorrectly. Attach the embroidery foot correctly. B-42
Screw of the embroidery foot is loose. Securely tighten the screw of the embroidery
foot.
B-42
Stabilizer is not attached to fabric being
embroidered.
Attach stabilizer. E-11
Bobbin thread is incorrectly wound. Use a correctly wound bobbin. B-31
Fabric does not feed
through the machine
Needle is turned, bent or the point is dull. Replace the needle. B-45
Thread is entangled. Cut the entangled thread and remove it from
the race.
A-13
Fabric puckers There is a mistake in the upper or bobbin
threading.
Check the steps for threading the machine
and rethread it correctly.
B-36, B-38
Thread tension is set incorrectly. Adjust the thread tension. E-30
Needle is turned, bent or the point is dull. Replace the needle. B-45
Spool cap is set incorrectly. Check the method for attaching the spool
cap, then reattach the spool cap.
B-38
High-pitched sound
while sewing
Pieces of thread are caught in the race. Clean the race. A-15
Upper threading is incorrect. Check the steps for threading the machine
and rethread the machine.
B-38
There are scratches on the bobbin case. Replace the bobbin case, or consult your
authorized dealer.
A-15
A bobbin designed specifically for this machine
is not used.
Incorrect bobbins will not work properly. Only
use a bobbin designed specifically for this
machine.
B-36
Character pattern
does not turn out
Thread tension is set incorrectly. Adjust the thread tension. E-30
Problem Cause Solution Page
TROUBLESHOOTING
Maintenance and Troubleshooting
Appendix A-21
A
2
Machine does not
operate
There is no pattern selected. Select a pattern. E-3, E-58
“Start/Stop” button was not pushed. Press the “Start/Stop” button. B-10
Main power switch is not turned on. Turn the main power to ON. B-17
Presser foot is not lowered. Lower the presser foot. B-10
All keys and buttons have been locked by
.
Press to unlock all keys and
buttons.
B-42, B-45
Nothing happens,
even if the LCD
display is pressed
The screen has been locked. Press either of the following keys to unlock
the screen.
—
The fabric feeds in the
opposite direction.
The feed mechanism is damaged. Contact your dealer or the nearest authorized
service center.
—
The LCD screen is
fogged up.
Condensation has formed on the LCD screen. After a while, the cloudiness will disappear. —
Embroidery pattern
does not sew out
correctly
Thread is twisted. Use scissors, etc., to cut the twisted thread
and remove it from the race, etc.
A-13
Fabric was not inserted into the frame correctly
(fabric was loose, etc.).
If the fabric is not stretched tight in the frame,
the pattern may turn out poorly or there may
be shrinkage of the pattern. Set the fabric
into the frame correctly.
E-14
Stabilizing material was not attached. Always use stabilizing material, especially
with stretch fabrics, lightweight fabrics,
fabrics with a coarse weave, or fabrics that
often cause pattern shrinkage. See your
authorized dealer for the proper stabilizer.
E-11
There was an object placed near the machine,
and the carriage or embroidery frame hit the
object during sewing.
If the frame bumps something during sewing,
the pattern will turn out poorly. Do not place
anything in the area where the frame may
bump it during sewing.
E-21
Fabric outside the frame edges interferes with
the sewing arm, so the embroidery unit cannot
move.
Reinsert the fabric in the embroidery frame so
that the excess fabric is away from the
sewing arm, and rotate the pattern 180
degrees.
E-14
Fabric is too heavy, so the embroidery unit
cannot move freely.
Place a large thick book or similar object
under the arm head to lightly lift the heavy
side and keep it level.
—
Embroidery pattern
does not sew out
correctly
Fabric is hanging off the table. If the fabric is hanging off the table during
embroidery, the embroidery unit will not
move freely. Place the fabric so that it does
not hang off the table or hold the fabric to
keep it from dragging.
E-21
Fabric is snagged or caught on something. Stop the machine and place the fabric so that
it does not get caught or snagged.
—
Embroidery frame was removed during sewing
(for example, to reset the bobbin). The
embroidery foot was bumped or moved while
removing or attaching the embroidery frame, or
the embroidery unit was moved.
If the embroidery foot is bumped or the
embroidery unit is moved during sewing, the
pattern will not turn out. Be careful when
removing or reattaching the embroidery
frame during sewing.
E-26
Stabilizer is incorrectly attached, for example, it
is smaller than the embroidery frame.
Attach the stabilizer correctly. E-11
Loops appear on the
surface of the fabric
when embroidering
The thread tension is incorrectly set. Adjust the thread tension. E-30 to E-32
The tension of the upper thread is incorrectly
set for the combination of the fabric, thread and
pattern being used.
Use the embroidery needle plate cover. E-22
The combination of the bobbin case and
bobbin thread is incorrect.
Change the bobbin case or bobbin thread so
that the correct combination is used.
E-21
Embroidery unit does
not operate
There is no pattern selected. Select a pattern. E-3, E-58
Main power switch is not turned on. Turn the main power to ON. B-17
Embroidery unit is not attached correctly. Reattach the embroidery unit correctly. B-47
Embroidery frame was attached before the unit
was initialized.
Perform the initialization process correctly. B-47
Pointer of embroidery
foot “W+” with LED
pointer does not
indicate the position
correctly
With thick or elastic fabric, the position will be
misaligned only at raised parts in the fabric.
Manually adjust the position according to the
thickness of the fabric.
B-44
With fabric having a very uneven surface, the
position is not correctly aligned.
The pointer indication should be used only as
a reference.
B-43
Problem Cause Solution Page
ERROR MESSAGES
A-22
If the machine is not properly set and the “Start/Stop” button is pressed, or if the operation procedure is
incorrect, the machine does not start. An alarm sounds and an error message is displayed on the LCD. If
an error message displays, follow the instructions in the message.
Below is an explanation of error messages. Refer to these when necessary (if you press or do the
operation correctly while the error message is displayed, the message disappears).
Specifying with
sensor pen cannot be
done accurately
The sensor pen has not been calibrated. Before using the sensor pen for the first time,
be sure to calibrate it.
B-56
The pen is being held differently than when it
was calibrated.
When using the sensor pen, be sure to hold it
at the same angle as when it was calibrated.
The specification location may be misaligned
if the pen is held at a slightly different angle.
In this case, make fine adjustments after
making the selection.
B-56
CAUTION
• This machine is equipped with a thread detection device. If the “Start/Stop” button is pushed before the
upper threading is done, the machine will not operate properly. Also, depending on the pattern selected,
the machine may feed the fabric even if the needle is raised. This is due to the needle bar release
mechanism. At these times, the machine will make a sound different from what is made during normal
sewing. This is not the sign of a malfunction.
• If the power is disconnected during sewing:
Turn the main power to OFF and unplug the machine.
If you restart the machine, follow the instructions for operating the machine correctly.
ERROR MESSAGES
CAUTION
• Be sure to rethread the machine. If you press the “Start/Stop” button without rethreading the machine,
the thread tension may be wrong or the needle may break and cause injury.
Marks Error Messages Cause/Solution
A malfunction occurred.Turn the machine off, then on again. This message is displayed if some malfunction occurs.
Attach the embroidery frame. This message appears if the embroidery frame is not attached
when you press in the embroidery screen. (see page
B-58)
Check and rethread the upper thread. This message is displayed when the upper thread is broken or
not threaded correctly, and the “Start/Stop” button is pressed.
Data volume is too large for this pattern. This message is displayed when the patterns you are editing
take up too much memory, or if you are editing too many
patterns for the memory.
Failed to save file. This message appears when you try to save more than 100
settings screen image files in the USB media. In this case,
delete a file from the USB media or use different USB media.
(see page B-28)
Lower the presser foot lever. This message is displayed when the “Presser Foot Lifter”
button is pushed while the presser foot lever is raised/the
needle is lowered.
Move the sensor pen away from the currently marked position. This message appears when you press down the sensor pen
tip before pressing and keep pressing for the certain
period. Move the sensor pen away from the current position.
Problem Cause Solution Page
ERROR MESSAGES
Maintenance and Troubleshooting
Appendix A-23
A
2
Not enough available memory to save the pattern. Delete
another pattern?
This message is displayed when the memory is full and the
pattern cannot be saved.
OK to automatically lower the presser foot?
This message is displayed when is pressed (the
presser foot is raised).
OK to delete the selected pattern? This message is displayed when the selected pattern is about
to be deleted.
OK to recall and resume previous memory? This message appears if the machine is turned off while
sewing, then turned on again.
Press to return the machine to the condition (pattern
position and number of stitches) when it was turned off. Follow
the procedure described in “If the Thread Breaks During
Sewing” on page E-27 to align the needle position and sew the
remainder of the pattern.
OK to reset the pattern’s border setting, position and/or angle? This message appears when you try to use the automatic
positioning function using the sensor pen with the pattern,
rotated or replaced, or with the border pattern. (see page B-58)
OK to revert to the original position and/or angle? This message appears when you try to use the automatic
positioning function using the sensor pen with the pattern,
rotated or replaced. (see page B-58)
Preventive maintenance is recommended. This message is displayed when the machine needs to be
maintained. (see page A-15)
Retrieving the pattern. Wait a moment. This message is displayed when the machine is retrieving a
previously saved pattern while in “Embroidery Edit” mode.
Sensor module error. This message appears when something is wrong with the
sensor unit of the machine. Consult your authorized dealer.
Set the clock. This message appears when the time/date is not set. Set
time/date. (see page B-18)
The bobbin thread is almost empty. This message is displayed when the bobbin thread is running
out.
The bobbin winder safety device has activated. Is the thread
tangled?
This message is displayed when the bobbin is being wound,
and the motor locks because the thread is tangled, etc.
The carriage of the embroidery unit will move. Keep your
hands etc. away from the carriage.
This message appears before embroidery unit moves.
The needle will move. Keep your hands etc. away from the
needle area.
This message appears when you touch the point closer than 2
cm from the needle drop point with the sensor pen in the
sensor function. (see page B-55)
The pattern field extends out of the pattern area, repeat setting
the position and angle using the sensor pen.
This message appears when the specified pattern position
extends out of the pattern area. Specify more centered
position of the embroidery frame. (see page B-58)
The pockets are full. Delete a pattern. This message is displayed when the memory is full and a
pattern must be deleted.
The safety device has been activated.Is the thread tangled? Is
the needle bent?
This message is displayed when the motor locks due to
tangled thread or for other reasons related to thread delivery.
The shutoff support mode has been activated. Turn off the
machine.
This message appears when the machine is in the shutoff
support mode. Turn off the machine once to start the machine
again. (see page B-25)
The upper thread may not be threaded correctly. Thread the
upper thread from the beginning.
This message is displayed when it seems that the upper
thread has not been threaded correctly.
The USB media was changed. Do not change the USB media
while it is being read.
This message is displayed when you attempt to select a
pattern after the USB media in which the pattern is saved has
been changed.
There is no needle plate cover. Attach a needle plate cover. This message is displayed when the needle plate cover is not
attached.
This file cannot be used. This message appears if the file format is incompatible with
this machine. Check the list of compatible file formats. (see
page E-44)
Marks Error Messages Cause/Solution
ERROR MESSAGES
A-24
This file exceeds the data capacity and cannot be used. Use a
suitable size file.
This message is displayed when the file size exceeds the data
capacity of the machine.
Confirm the file size and format. (see page E-45)
This function cannot be used while in the sensor mode. This message appears when the selected function is not
available with the sensor function. (see page B-53)
This key does not operate when the needle is down. Raise the
needle and press the key again.
This message is displayed when a key on the LCD display is
touched while the needle is in the down position.
This USB media cannot be used. This message is displayed when you try to use incompatible
media.
This USB media is incompatible. This message is displayed when you try to use incompatible
USB media. For a list of compatible USB media, visit
“ http://support.brother.com/
”.
Transmitting by USB This message is displayed while the USB media is
transmitting.
Turn off the power and replace the needle plate. This message is displayed when the needle plate is removed
with the machine on or when the machine is turned on and
“Embroidery” or “Embroidery Edit” mode is selected (see page
B-20).
USB media error This message is displayed when an error occurs with the USB
media.
USB media is not loaded. Load USB media. This message is displayed when you try to recall or save a
pattern while no USB media is loaded.
Use the presser foot lifter button to lower the presser foot. This message is displayed when a button, such as the
“Start/Stop” button, is pushed while the presser foot is raised.
Marks Error Messages Cause/Solution
SPECIFICATIONS
Maintenance and Troubleshooting
Appendix A-25
A
2
* Please be aware that some specifications may change without notice.
SPECIFICATIONS
Item Specification
Embroidery Machine and Accessories
(Box 1 of 2)
Dimensions of machine Approx. 57.1 cm (W) × 33.2 cm (H) × 28.4 cm (D) (approx.
22-1/2 inches (W) × 13-1/16 inches (H) × 11-3/16 inches (D))
Dimensions of box Approx. 68.5 cm (W) × 55.0 cm (H) × 37.7 cm (D) (approx.
26-15/16 inches (W) × 21-5/8 inches (H) × 14-13/16 inches
(D))
Weight of machine Approx. 13.9 kg (approx. 30.6 lb)
Weight of box (for shipping) Approx. 19.0 kg (approx. 41.9 lb)
Embroidering speed 100 to 1050 stitches per minute
Embroidery Unit
(Box 2 of 2)
Dimensions of embroidery unit Approx. 54.5 cm (W) × 13.0 cm (H) × 46.4 cm (D) (approx.
21-7/16 inches (W) × 5-1/8 inches (H) × 18-1/4 inches (D))
Dimensions of machine with
embroidery unit attached
Approx. 81.5 cm (W) × 33.2 cm (H) × 46.4 cm (D) (approx.
32-1/16 inches (W) × 13-1/16 inches (H) × 18-1/4 inches (D))
Dimensions of box Approx. 68.5 cm (W) × 55.0 cm (H) × 18.8 cm (D) (approx.
26-15/16 inches (W) × 21-11/16 inches (H) × 7-7/16 inches
(D))
Weight of embroidery unit Approx. 3.9 kg (approx. 8.5 lb)
Weight of box (for shipping) Approx. 6.0 kg (approx. 13.2 lb)
Total Shipping Weight (Combination of 2 boxes complete) Approx. 27.0 kg (approx. 59.5 lb)
UPGRADING YOUR MACHINE’S SOFTWARE
A-26
You can use USB media or a computer to upgrade software for your machine.
When an upgrade program is available on “ http://support.brother.com/
”, please download the files
following the instructions on the website and steps below.
Upgrade Procedure Using USB
Media
a
While pressing the “Automatic Threading”
button, turn the main power to ON.
The following screen will appear on the LCD.
b
Press .
c
Insert the USB media into the USB port for
media/mouse on the machine. The media
device should only contain the upgrade file.
a USB port for media/mouse
b USB media
d
Press .
The upgrade file is loaded.
e
Remove the USB media, and turn the
machine off and on again.
UPGRADING YOUR MACHINE’S SOFTWARE
Note
• When using USB media to upgrade the software, check that no data other than the upgrade file is
saved on the USB media being used before starting to upgrade.
Note
• The access lamp will begin blinking after
inserting USB media, and it will take about 5
to 6 seconds to recognize the media. (Time
will differ depending on the USB media).
Note
• If an error occurs, a red text error message
will appear. When the installation is
performed successfully, following message
will appear.
UPGRADING YOUR MACHINE’S SOFTWARE
Maintenance and Troubleshooting
Appendix A-27
A
2
Upgrade Procedure Using
Computer
Do not connect any additional USB media devices
to your computer when using the USB cable.
a
While pressing the “Automatic Threading”
button, turn the main power to ON.
The following screen will appear on the LCD.
b
Press .
c
Plug the USB cable connector into the
corresponding USB ports for the computer
and for the machine.
“Removable Disk” will appear in “Computer (My
computer)”.
d
Copy the upgrade file to “Removable Disk”.
The following message will appear.
e
When the message disappears, press
.
The upgrade file is loaded.
f
Unplug the USB cable, and turn the
machine off and on again.
Note
• Do not connect any additional USB media
devices to your computer when using the
USB cable.
Note
• If an error occurs, a red text error message
will appear. When the installation is
performed successfully, following message
will appear.
INDEX
A-28
A
Accessories
options
................................................................................. B-13
Adjusting the LED pointer
........................................................ B-44
Air vent
...................................................................................... B-8
Aligning the position
................................................................. E-36
Alphabet characters
embroidery
............................................................................. E-5
embroidery edit
..................................................................... E-59
Appliqué
embroidery patterns
.............................................................. E-23
using an embroidery frame pattern
........................................ E-51
Array key
....................................................................... E-60, E-64
Arrow keys
..................................................................... E-36, E-81
Automatic Threading button
......................................... B-10, B-38
B
Ball point needle 75/11 ............................................................. E-33
Bobbin
runs out of thread
.................................................................. E-26
setting
.................................................................................. B-36
winding
................................................................................ B-31
Bobbin case
bobbin case
.......................................................................... E-21
cleaning
............................................................................... A-15
Bobbin clip
.............................................................................. B-12
Bobbin cover
.................................................................. B-9, B-37
Bobbin holder (switch)
............................................................. B-33
Bobbin winder
........................................................................... B-8
Bobbin work
.............................................................................. A-2
Border key
..................................................................... E-72, E-76
C
Calibrating the sensor pen ........................................................ B-56
Character spacing key
............................................................... E-64
Cleaning
LCD screen
.......................................................................... A-15
machine casing
.................................................................... A-15
race
...................................................................................... A-15
Combining Patterns
embroidery edit
..................................................................... E-80
Custom Thread Table
..................................................... E-68, E-71
Cut/Tension key
........................................................................ E-30
D
Density key ............................................................................... E-40
E
Eco mode ................................................................................. B-25
Editing
embroidery
........................................................................... E-36
embroidery edit
..................................................................... E-61
Embroidery
adjusting the speed
............................................................... E-33
automatic thread cutting function (END COLOR TRIM)
........ E-32
edges or corners
.................................................................... E-16
key functions
......................................................................... E-10
restarting from the beginning
................................................. E-28
resuming embroidery after turning off the power
................... E-28
ribbons or tape
...................................................................... E-16
selecting patterns
.................................................................... E-3
small fabrics
.......................................................................... E-16
thread color display
.............................................................. E-34
thread trimming function (JUMP STITCH TRIM)
.................... E-32
Embroidery card
......................................................................... E-7
Embroidery card reader
.............................................................. E-7
Embroidery edit
changing the thread color
..................................................... E-67
combined patterns
...................................................... E-80, E-83
custom thread table
.................................................... E-68, E-71
explanation of functions
....................................................... E-57
key functions
........................................................................ E-62
repeated patterns
.................................................................. E-72
Embroidery foot
........................................................................ B-42
Embroidery foot screw
................................................................ B-9
Embroidery frame display
......................................................... E-35
Embroidery frames
attaching
.............................................................................. E-17
inserting fabric
...................................................................... E-14
removing
.............................................................................. E-17
types
..................................................................................... E-13
using the embroidery sheet
................................................... E-15
Embroidery key
........................................................................ E-79
Embroidery needle plate cover
................................................. E-22
Embroidery patterns
aligning the position
............................................................. E-36
checking the position
........................................................... E-19
combining
............................................................................ E-80
duplicating
........................................................................... E-78
editing
.................................................................................. E-61
linked characters
.................................................................. E-41
patterns which use appliqué
................................................. E-23
retrieving
.................................................................... E-48, E-49
revising
................................................................................. E-36
saving
.............................................................. E-45, E-46, E-47
selecting
....................................................................... E-3, E-58
sewing
.................................................................................. E-21
using a frame pattern to make an appliqué
................. E-51, E-52
Embroidery sheet
...................................................................... E-15
Embroidery unit
............................................................... B-9, B-47
carriage
.................................................................................. B-9
Error messages
.......................................................................... A-22
F
Forward/Back key ........................................................... E-27, E-28
H
Handle ....................................................................................... B-8
Handwheel
................................................................................ B-8
Home page screen
................................................................... B-20
I
Image key ................................................................................. E-20
K
Key functions
embroidery
........................................................................... E-10
embroidery edit
.................................................................... E-62
L
LCD screen ..................................................................... B-8, B-20
cleaning
............................................................................... A-15
Lower threading
setting the bobbin
................................................................. B-36
winding the bobbin
.............................................................. B-31
INDEX
INDEX
Appendix A-29
A
2
M
Machine help key ..................................................................... B-29
Machine operation mode key
................................................... A-19
Main power switch
.......................................................... B-8, B-17
Mirror image key
...................................................................... E-39
Multi color key
.............................................................. E-40, E-66
N
Needle
changing the needle
............................................................. B-45
mode
.................................................................................... B-20
Needle bar thread guides
............................................................ B-9
Needle clamp screw
................................................................... B-9
Needle plate
............................................................................... B-9
Needle Position button
............................................................. B-10
O
Operation buttons ........................................................... B-8, B-10
P
Power cord ............................................................................... B-18
Power cord receptacle
................................................................ B-8
Presser foot
attaching
............................................................................... B-42
removing
.............................................................................. B-42
Presser foot code
........................................................................ E-9
Presser foot lever
........................................................................ B-8
Presser Foot Lifter button
.......................................................... B-10
Presser foot/Needle exchange key
................................. B-42, B-45
Pre-tension disk
.................................................... B-8, B-33, B-35
R
Race ......................................................................................... A-15
Repeated patterns
..................................................................... E-72
Retrieving
computer
.............................................................................. E-50
embroidery patterns
.............................................................. E-48
machine’s memory
............................................................... E-48
USB media
........................................................................... E-49
Rotate key
..................................................................... E-38, E-63
S
Saving
computer
.............................................................................. E-47
embroidery patterns
.............................................................. E-45
machine’s memory
............................................................... E-45
USB media
........................................................................... E-46
Screen brightness
...................................................................... A-18
Sensor functions
....................................................................... B-52
embroidering position
........................................................... B-58
Sensor pen
................................................................................ B-53
Sensor pen holder
..................................................................... B-53
Settings
automatic thread cutting
....................................................... E-32
display language
................................................................... B-26
machine setting mode key
.............................. B-22, E-33, E-68
sewing settings
...................................................................... B-22
thread tension
....................................................................... E-30
thread trimming
.................................................................... E-32
Shutoff support mode
............................................................... B-25
Size key
......................................................................... E-37, E-63
Speaker
.................................................................................... B-22
Special spool cap
..................................................................... B-32
Specifications
........................................................................... A-25
Spool cap
................................................................................... B-8
Spool net
.................................................................................. B-41
Spool pin
.................................................................................... B-8
Stabilizer
.................................................................................. E-11
Start/Stop button
...................................................................... B-10
Starting point key
...................................................................... E-37
Supplemental spool pin
.................................................. B-8, B-31
T
Thread
thread tension
....................................................................... E-30
Thread color display
................................................................. E-34
Thread cutter
............................................................................. B-8
Thread Cutter button
................................................................ B-10
Thread guide
........................................................ B-8, B-32, B-35
Thread guide plate
............................................... B-8, B-35, B-38
Thread marks
............................................................................ E-75
Thread palette key
.............................................. E-66, E-67, E-71
Top cover
.................................................................................. B-8
Touch pen
.................................................................... E-67, A-18
Trial key
.................................................................................... E-19
Troubleshooting
....................................................................... A-19
U
Uninterrupted embroidering ..................................................... E-43
Upgrading
................................................................................ A-26
Upper threading
using the “Automatic Threading” button
.............................. B-38
using the spool net
............................................................... B-41
USB cable
................................................ B-49, E-47, E-50, A-27
USB media
recalling
................................................................................ E-49
saving
................................................................................... E-46
usable
................................................................................... E-44
USB mouse
................................................................... B-25, B-50
USB port connector
for computer
................................................................ B-8, E-47
for media
.............................................................................. E-46
English
882-D80/D82
Printed in Taiwan
XF3635-2012
Please visit us at http://support.brother.com/ where you can get
product support and answers to frequently asked questions (FAQs).
