Loading ...
Loading ...
Loading ...
Review this chart to find do-it-yourself solutions for minor performance problems. Any ser-
vice needed, other than those described in this owner's manual, should be performed by
an authorized service representative.
........... Failure to do so co,ul,,?' resu,l,l,,in electrical sho?,k ?,,[,,,,perso?,,?I injury_
Cleaner won't start- I. Unplugged at wall outlet,
2. Tripped cimuil breaker/blown fuse
at household service panel
3+ Loose hose electrical connections
4,, Tripped overload protector in
POWER-MATE TM.
Poorjob of dirt 1+
pick-up. 2.
3+
4_
5.
6.
7,
8.
9.
10,
Cleanerstarts but
cutsoff°
POWER-MATETM will not
run when attached.
Performance indicator,
somemodels,is red,
Cleanerpicksupmoveable
rugs ,or- POWER-MATETM
)ushee toohard,
Fullor cloggeddust bag.
Cloggedairflow passages
Dirtymotorsafetyfilter
Wrong pile heightsetting
Open auctioncontrol
Holein hose
Worn POWER-MATETM brushes
Worn or broken belt
Dirtybrush orbrushsupports
Canisterhoodopen
'L Hose or hood electrical connections
Tripped overload proteclor in
POWER.MATEm,,
Trippedoverloadprotector
in canister
1. POWER-MATE TM connections
unplugged.
2. Worn or broken belt.
3, Dirty brush or brush supports
4. Tripped ovedoad protecior in
POWER-MATE _'-
Io Furlorcloggeddust bag
2_ Dirtyfilter
3. Cloggedairflow passage.
4, Certainattachmenttools
t. Wrong pile height setting
2. Suction too strong
Lightwon'twork. 1. Burned outlightbulb
Cordwor_'trewind+ 1, Dirty powercOrdr
2o Cordjammed.
Cleanerleaves marks I+ Wrongvacuumingpattern
on carpet
17
1. Plug in firmly, push ONtOFF switch to ON
2. Reset circuit breaker or replace fuse
3. Reconnecthoseends, (page7)
4. Clean brushand brush supports,
thenreset,(pages 14, 15)
1. Change bag, (page 12)
2o Clear airflow passages, (page 12)
3. Clean filter, (page 13).
4. Adjust setting, (page 9),
5+ Adjust control,(page 11)
6. Replace hose
7. Change brushes, (page 16},
8 & 9+ See BELT CHANGING AND BRUSH
CLEANING, (pages 14, 15)+
10. Close and latch hood_
1.
Checkconnections,reconnect hose
ends,(page7).
2+ Removeany items thatmay becaught
orjammed, thenreset. If cleanerstarts
andstops again+cleanbrush andbrush
supports,thenreset,(pages"_4,_,5)
3. Changedust bag, clearairflowblockage,
(page 12). Wait 20 minutesfor motor
tocool andautomaticallyreset.
2&3o
4+
Plug in firmly, (page 6).
See BELT CHANGING AND BRUSH
CLEANING, (pages 14, 15).
Check brush area for excessive lint
build-up or jamming CIean brush and
brush supports, then reset, (pages 14, 15)
1+ Change bag, (page t2)
2. Change tiller, (page 13)
3. Clear clog from airflow passage, (page 12)
4+ This is normal Light should go off
when loo_is removed
1. Adjustsetting,(page9)
2+Open suctioncontrol,(page 11)
1+Change lightbulb,(page14)
1. Cleanthe powercord
2, Pulloulcordand rewind
1_SeeVACUUMING"rIPS,(page 9)..
Loading ...
Loading ...
Loading ...