Loading ...
Loading ...
Loading ...
11
Set-up Codes
■ The WOOLENS key pad will advance you from code to code.
■ The PERM PRESS key pad will change the code value.
■ The DELICATES/KNITS key pad will select or deselect
options.
The set-up code is indicated by the
one or
two left-hand
characters. The set-up code value is indicated by the two or
three right-hand characters.
CODE EXPLANATION
79 WASH LENGTH
79
This is the number of minutes for WASH. Washer
comes from the factory preset with 9 minutes.
Ch
oose from 9-17 minutes by pressing the PERM
PRESS key pad.
P
ress the WOOLENS key pad once to advance
to next code.
800 ADDITIONAL RINSE OPTION
This option is either SELECTED “ON” or
NOT SELECTED “OFF.”
8
8
00
Ar
Not Selected “OFF.”
Selected “ON.” Cannot be combined with the
Super Cycle
rinse option.
P
ress the DELICATES/KNITS k
e
y pad once for this
selection.
Press the WOOLENS key pad once to advance
to next code.
900 CYCLE COUNTER OPTION
This option is either SELECTED “ON” or
NOT SELECTED “OFF.”
9
9
00
0C
Not Selected “OFF.”
Selected “ON” and not able to be deselected.
Press the DELICATES/KNITS key pad
3 consecutive times to select “ON.” Once selected
“ON” it cannot be deselected.
Press the WOOLENS key pad once to advance
to next code.
CODE EXPLANATION
5. 00 TIME-OF-DAY CLOCK, MINUTES
5. 00
This is the TIME-OF-DAY CLOCK, minute setting;
select 0-59 minutes by pressing the PERM PRESS
key pad.
Press the WOOLENS key pad once to advance
to next code.
6. 00 TIME-OF-DAY CLOCK, HOURS
NOTE: Use
s
the 24 hr. clock
6. 00
This is the TIME-OF-DAY CLOCK, hour setting;
select 0-23 hours by pressing the PERM PRESS
key pad.
Press the WOOLENS key pad once to advance
to next code.
r. 800 TOP SPIN SPEED RPM
r. 800
This can be selected from the following spin
speeds: 600 rpm, 750 rpm, 800 rpm, 1000
(dis
plays as 999) rpm. Step between speeds by
pressing th
e PERM PRESS key pad. Factory pre-
set for 800 rpm.
Press the WOOLENS key pad once to advance
to next code.
A1. 00 PREWASH LENGTH
A1. 00
This is the number of minutes of PREWASH.
Choose 0 to disable the prewash or select between
2 and 7 minutes by pressing the PERM PRESS key
pad.
Press the WOOLENS key pad once to advance
to next code.
A2. 03 FINAL SPIN LENGTH
A2. 03
This is the number of minutes of final high speed
spi
n. Choose from 3-8 minutes by pressing the
PERM PRESS key pad.
Press the WOOLENS key pad once to advance
to next code.
If cycle counter (9 0C) is select
ed, the following is true:
1 00 Number of cycles in
HUNDREDS.
1
02
= 200
2 00 Number of cycles in ONES. 2 25 = 25
TOTAL CYCLES = 225 cycles
This is “VIEW ONLY” and cannot be cleared.
Pr
ess the WOOLENS button once to advance to
next code.
EXIT FROM SET-UP MODE
Remove power, open console, reinsert plug into AA1, close console,
and apply
power.
Washer Diagnostic Mode
To enter the “Washer Diagnostic Mode,” first enter “Start
Operating Set-up.” Then press and hold the DELICATES/KNITS
key pad for 1 second while in set-up code 6, anytime a
diagn
ostic code
is present.
On entry to diagnostic mode the
en
tire display will flash, a
cycle in process is canceled, money in escrow is cleared, and
diag
nostic codes are cleared. If a diagnostic code persists,
it must be corrected before the following cycle options
are permitted.
There are five possible ways to initiate cycle activity from
diagnostic mode as follows:
1. Washer Cleanout cycle - With the entire display flashing, this
cycle is started
by pressing the BRIGHTS key pad.
Use the Washer Cleanout cycle once a month to keep the
in
si
de of your washer fresh and clean. This cycle uses a
higher water level. Use with liquid chlorine bleach to
thoroughly clean the inside of the washer. This cycle should
not be interrupted.
IMPORTANT: Do not place garments or other
items in the
washer during the Washer Cleanout cycle. Use this cycle with
an empty wash drum.
Loading ...
Loading ...
Loading ...