Loading ...
Loading ...
Loading ...
18
Troubleshooting
REPLACEMENT
PARTS
To obtain replacement parts,
contact the local retailer
in your area or log onto
weber.com.
Lighting Your Barbecue with a
Match
Using a Match to Determine if there is
Gas Flow to the Burners
1) Open the barbecue lid.
2) Check that all burner control knobs are in the
o
position. Check by pushing in and turning
knobs clockwise.
Note: It is important that all burner control knobs be in
the o position before you turn on the LPG cylinder.
3) Turn gas supply on by turning cylinder valve
anti-clockwise.
4) Begin with burner 1, furthest to the left. Put match in
the matchstick holder and strike match. (Matchstick
holder is located under left side table.) Insert lit
match down through the cooking grills, past the
FLAVORIZER BARS and next to the burner(A).
5) Push the burner control knob in and turn it anti-
clockwise to the start/high
position.
6) Check that the burner is lit by looking through the
cooking grills and through the FLAVORIZER BARS.
7) If the burner does not ignite within 4 seconds,
turn burner control knob to the o
position and
wait five minutes to allow the gas to clear before
attempting to light the burner again. If repeated
attempts fail, follow the gas flow troubleshooting
instructions on the next page.
8) If the burner ignites, the problem lies in the ignition
system. Follow the instructions for “Checking the
Components of the Electronic Ignition System”.
9) After burner 1 ignites, you can turn on burner 2
(and burner 3).
10) Replace the matchstick holder by hanging
underneath the left side table (B).
A
B
MAIN BURNERS or SIDE BURNER WILL NOT IGNITE
SYMPTOM
• Main burners or side burner do(es) not ignite when following the electronic ignition instructions in the “Operation” section of
this owner's manual.
CAUSE SOLUTION
There is a problem with gas flow. If any burner does not ignite, the first step is to determine if there is gas flowing to the burner(s). Tocheck
this, follow the instructions below for “Lighting Your Barbecue with a Match.”
If match lighting IS NOT successful, follow the “GAS FLOW” troubleshooting suggestions on the next page.
There is a problem with the electronic ignition system. If any burner does not ignite, the first step is to determine if there is gas flowing to the burner(s). Tocheck this,
follow the instructions below for “Lighting Your Barbecue with a Match.”
If match lighting IS successful, follow the instructions for “Checking the Components of the Electronic
IgnitionSystem.”
Using a Match to Determine if there is
Gas Flow to the Side Burner
1) Open the side burner lid.
2) Check that the side burner control knob is in the
o
position. Check by pushing in and turning knob
clockwise. Also check that all main burner control
knobs are in the o position.
Note: It is important that all burner control knobs
are in the o position before turning on the LPG
cylinder.
3) Turn gas supply on by turning cylinder valve
anti-clockwise.
4) Put match in the matchstick holder and strike
match. (Matchstick holder is located under left side
table.) Hold lit match by the side burner(C).
5) Push the burner control knob in and turn it anti-
clockwise to the start/high
position.
6) Check that the side burner is lit. The side burner
flame may be dicult to see on a bright sunny day.
7) If the side burner does not ignite within 4 seconds,
turn side burner control knob to the o
position
and wait five minutes to allow the gas to clear
before attempting to light the burner again.
If repeated attempts fail, follow the gas flow
troubleshooting instructions on the next page.
8) If the burner ignites, follow the instructions for
“Checking the Components of the Electronic Ignition
System”.
Loading ...
Loading ...
Loading ...