D6 Instructions for Use
Figure: Your machine may look
different to the one shown.
K
For your safety: read and understand manual before use.
E
2
Table of contents
Your D6
IMPORTANT SAFEGUARDS 4
Control elements 8
1 Preparing and using for the first time 10
JURA on the Internet .................................................................................................................................... 10
Setting up the machine ..............................................................................................................................10
Filling the bean container ........................................................................................................................... 10
Determining the water hardness ...............................................................................................................11
First-time use .................................................................................................................................................11
Connecting milk ........................................................................................................................................... 13
Connect accessory (with wireless connection) .......................................................................................14
2 Preparation 15
Espresso and coffee .....................................................................................................................................16
Two specialty coffees at the touch of a button .......................................................................................16
Cappuccino....................................................................................................................................................16
Milk foam .......................................................................................................................................................17
Permanently setting the amount of water for the cup size .................................................................18
Adjusting the grinder ..................................................................................................................................19
Hot water .......................................................................................................................................................19
3 Daily operation 20
Filling the water tank .................................................................................................................................. 20
Switching on ................................................................................................................................................20
Daily maintenance ......................................................................................................................................20
Regular maintenance ..................................................................................................................................21
Switching off the machine ..........................................................................................................................21
4 Permanent settings in programming mode 23
Product settings ..........................................................................................................................................24
Setting the water hardness .......................................................................................................................25
Automatic switch-off ..................................................................................................................................26
Unit for amount of water ...........................................................................................................................26
Language ...................................................................................................................................................... 27
5 Maintenance 28
Rinsing the fine foam frother ....................................................................................................................28
Cleaning the fine foam frother .................................................................................................................29
Dismantling and rinsing the fine foam frother......................................................................................30
Inserting/changing the filter .......................................................................................................................31
Cleaning the machine ................................................................................................................................32
Descaling the machine ..............................................................................................................................33
Cleaning the bean container .....................................................................................................................35
Descaling the water tank ...........................................................................................................................35
3
Table of contents
6 Display messages 36
7 Troubleshooting 37
8 Transport and environmentally friendly disposal 38
Transport/ Emptying the system .............................................................................................................38
Disposal .........................................................................................................................................................38
9 Technical data 39
10 Index 40
11 JURA contact details/ Legal information 44
Symbol description
Warnings
This is the safety alert symbol. lt is used to alert you to potential personal injury
hazards. Obey all safety messages that follow this symbol to avoid possible injury
or death.
DANGER indicates a hazardous situation which, if not avoided, will result in death
or serious injury.
WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
J CAUTION
CAUTION, used with the safety alert symbol, indicates a hazardous situation
which, if not avoided, could result in minor or moderate injury.
NOTICE NOTICE is used to address practices not related to personal injury.
Symbols used
T
Prompt to take action. This symbol means that you are being prompted to
perform some action.
E
Information and tips to make it even easier to use your D6.
COFFEE
Display message
J
J DANGER
J WARNING
4
IMPORTANT SAFEGUARDS
IMPORTANT SAFEGUARDS
SAVE THESE INSTRUCTIONS.
Pass them on to any subsequent user.
When using electrical appliances, basic safety precautions shall
always be followed, to reduce the risk of fire, electric shock, and/or
injury to persons, including the following:
Z Read all instructions.
Z Do not touch hot surfaces. Use handles or knobs.
Z To protect against fire, electric shock and injury to persons, do
not immerse power cord, plugs, or body of machine in water
or other liquid.
Z Close supervision is necessary when any appliance is used by
or near children.
Z Unplug from outlet when not in use and before cleaning.
Allow to cool before putting on or taking off parts, and before
cleaning the appliance.
Z Do not operate any appliance with a damaged cord or plug or
after the appliance malfunctions, or has been damaged in any
manner. Return appliance to the nearest authorized service
facility for examination, repair or adjustment.
Z The use of an accessory attachment not recommended by the
appliance manufacturer may result in fire, electric shock, or
injury to persons.
Z Do not use outdoors.
Z Do not let the cord hang over the edge of a table or counter,
or touch hot surfaces.
Z Do not place on or near a hot gas or electric burner, or in a
heated oven.
Z To disconnect, turn any control to ‘OFF’ then remove plug
from wall outlet.
Z Do not use appliance for other than intended use.
Z Use extreme caution when dispensing hot steam, hot water
or hot coffee.
Follow the basic safety
precautions
5
IMPORTANT SAFEGUARDS
The appliance is designed and intended for household use only. It
shall only be used for coffee preparation and to heat milk and water,
according to these instructions. Use for any other purpose will be
deemed improper. JURA Elektroapparate AG cannot accept any
responsibility for the consequences of improper use.
People, including children, who
Z do not have the physical, sensory or mental capabilities to use
the appliance safely or
Z are inexperienced or lack knowledge in how to use the
appliance safely
must be supervised by a responsible person when using it, or must
be instructed in how to use it correctly.
Z A short power-supply cord is to be provided to reduce risks
resulting from becoming entangled in or tripping over a
longer cord.
Z The cord shall be arranged so that it will not drape over the
counter top or table top where it can be pulled on by children
or tripped over.
Z This appliance has a 3-pin grounded plug.
Z Do not modify the plug in any way.
Extension cords are available an may be used if care is exercised in
their use.
If the user chooses to use an extension cord,
Z the marked electrical rating of the extension cord should be
at least as great as the electrical rating of the appliance, and
Z if the appliance is of the grounded type, the extension cord
should be a grounding type 3-wire cord, and
Z the longer cord should be arranged so that it will not drape
over the counter top or tabletop where it can be pulled on by
children or tripped over.
To reduce the risk of fire or electric shock, DO NOT remove any
service covers. DO NOT modify the appliance in any way that is not
described in these instructions. NO user serviceable parts included.
Repair MUST be done by authorized personnel only.
In the event of signs of damage, for example if there is a smell of
burning, unplug the machine immediately from outlet and contact
JURA customer service.
Intended use
Special power cord set
instructions
J WARNING
6
IMPORTANT SAFEGUARDS
This appliance is for household use. Any servicing other than
cleaning and user maintenance shall be performed by an authorized
service representative:
Z Do not immerse base in water or try to disassemble.
Z Do not put the appliance or any individual parts in the
dishwasher.
Z Check voltage to be sure that the voltage indicated on the
name plate complies with your voltage. The name plate is
located on the underside of the appliance.
Z Never use warm or hot water to fill the water container. Use
cold water only.
Z Keep your hands and the cord away from hot parts of the
appliance during operation.
There is a risk of scalds or burns on the spouts and the cappuccino
frother / nozzle.
Z Keep children away.
Z Do not touch any hot parts. Use the handles or knobs
provided.
Z Ensure that the cappuccino frother / nozzle is correctly fitted
and clean. If incorrectly fitted or if they become blocked, the
cappuccino frother or its parts might come off.
Z Never clean with scouring powders or hard implements.
Z Ensure that the ventilation slots are not covered.
Z Never pull out the drip tray during the brewing process. Only
pull the drip tray when the display instructs you or when the
appliance is ready for use.
J CAUTION
NOTICE
7
IMPORTANT SAFEGUARDS
Z Never fill instant coffee, chocolate mix etc. into the bean
container or ground coffee funnel (filler funnel for ground
coffee). It will damage the functioning of the brewing
chamber.
Z Never fill sugar coated coffee beans into the bean container.
In case of doubt, call your dealer.
Z Never fill anything other than coffee beans into the bean
container (no chocolate, no rice, no nuts, no spices, nothing
other than roasted coffee beans).
Z Never fill frozen beans into the bean container. If you store
beans in the freezer, let them thaw 3 to 4 hours before filling
them into the bean container.
Z Never fill anything but fresh, cold and clean water into the
water tank, except when decalcifying.
Z Never use mineral or carbonated water. You can use tap water,
bottled water, spring water and reverse osmosis water.
Z Never do anything with the machine which is not described in
these instructions. In case of doubt, call your dealer.
NEVER DO
(or you will void your
warranty protection):
8
Control elements
Control elements
15
14
4
3
7
8
6
5
2
1
9
10
13
11
12
J HOT
J HOT
1 On/Off button Q
2 Water tank cover
3 Water tank
4 Power cord (back of the machine)
5 Height-adjustable coffee spout
6 Coffee grounds container
7 Drip tray
8 Cup platform
9 Cover of filler funnel for cleaning tablet
10 Filler funnel for cleaning tablet
11 Bean container cover
12 Grinder adjustment switch
13 Bean container with aroma preservation
cover
14 Switch for hot water and milk foam
preparation
15 Fine foam frother
Figure: Your machine may look
different to the one shown.
9
Control elements
n nn n n n n n
cO n
1
2
3
4 5
1 Display
2 Rotary Switch
3 O P symbol (programming)
4 c Maintenance symbol
5 n Milk foam symbol
Service socket for optional JURA Smart Connect (under cover)
10
1 Preparing and using for the first time
1 Preparing and using for the first time
Visit us on the Internet (www.jura.com). You will find interesting and
up-to-date information on your D6 and on every aspect of coffee.
If you need assistance with using your machine, you can find this at
www.jura.com/service.
When setting up your D6, please note the following:
U
Place the D6 on a horizontal surface that is not sensitive to
water.
U
Choose a spot for your D6 which protects the machine against
overheating. Ensure that the ventilation slots are not covered.
The bean container has an aroma preservation cover. This will ensure
that your coffee beans retain their aroma for longer.
Coffee beans which have been treated with additives (e.g. sugar),
ground coffee or freeze-dried coffee will damage the grinder.
T Only use roasted, untreated coffee beans to fill the bean
container.
T Open the bean container cover and remove the aroma
preservation cover.
T Remove any dirt or foreign objects from inside the bean
container.
T Fill the bean container with coffee beans, then close the
aroma preservation cover and the bean container cover.
JURA on the Internet
Setting up the machine
Filling the bean container
NOTICE
11
1 Preparing and using for the first time
When you use the machine for the first time, you must set the water
hardness. If you do not know the hardness of your water, you can
find this out first. Use the Aquadur® test strips supplied with the
machine.
T Hold the test strip briefly (for 1second) under flowing water.
Shake off the water.
T Wait for about 1minute.
T You will then be able to read the degree of water hardness
from the discoloration of the Aquadur® test strip and the
description on the packaging.
Level Display German
Degree (°dH)
Degrees of general
hardness (°dGH)
Parts per
million (ppm)
Indicator Strip number
of ‘reddish’ fields
Not active – – – –
Very soft water <3 <3 < 53.4 None
Soft water > 4 > 4 > 71 1
Hard water > 8.4 > 8.4 > 150 2
Very hard water > 14 > 14 > 250 3
If the machine is operated with a defective power cord, there is a
danger of potentially fatal electric shock.
T Never use a machine which is damaged.
T Never use a machine which has a defective power cord.
Milk, sparkling mineral water or other liquids can damage the water
tank or the machine.
T Only fill the water tank with fresh, cold water.
E The water volume is given as standard in ‘oz’. You can change
this setting to ‘ml’ in programming mode (see Chapter 4
‘Permanent settings in programming mode – Unit for amount
of water’).
Determining the water
hardness
First-time use
J WARNING
NOTICE
12
1 Preparing and using for the first time
Precondition:The bean container has been filled.
T Insert the power plug into a power socket.
T Press the On/Off button Q to switch the D6 on.
LANGUAGE EN appears on the display.
T Press the Rotary Switch to confirm the setting.
OK appears briefly on the display.
HARDNESS, 16°dH
E If you do not know the hardness of your water, you can find
this out first (see Chapter 1 ‘Preparing and using for the first
time – Determining the water hardness’).
T Turn the Rotary Switch to change the water hardness
setting, e.g. to
25°dH.
T Press the Rotary Switch.
OK appears briefly on the display.
INSERT FILTER
T Open the water tank cover.
T Remove the water tank and rinse it with cold water.
T Open the filter holder.
T Insert the CLEARYL Smart filter cartridge into the water tank,
exerting slight pressure.
T Close the filter holder. It will click into place audibly.
T Fill the water tank with fresh, cold water and reinsert the
tank.
E The machine automatically detects that you have just inserted
the filter cartridge.
OK appears briefly on the display.
OPEN SWITCH, the light segment on the switch lights up.
T Place a receptacle (at least 17 oz or 500 ml) under the fine
foam frother and the coffee spout.
T Turn the switch to them position.
FILTER RINSING, water flows out of the fine foam
frother.
E You can interrupt rinsing of the filter at any time. To do this,
turn the switch clockwise. Turn the switch anticlockwise to
continue rinsing the filter.
n nn n n n n n
cO n
13
1 Preparing and using for the first time
E The water may be slightly discolored. This is not harmful to
health and does not affect the taste.
Rinsing of the filter stops automatically.
CLOSE SWITCH
T Turn the switch to the °position.
SYSTEM FILLING, the system fills up with water.
EMPTY TRAY
T Empty the drip tray and coffee grounds container and put
them back into the machine.
T Place a receptacle under the coffee spout.
HEATING
RINSING, the system is rinsed. Water flows out of the
coffee spout. The rinse stops automatically.
CAPPUCC.
appears on the display. Your D6 is ready for use.
Your D6 creates fine, creamy, feather-light milk foam with a perfect
consistency. The most important requirement for frothing milk is
a milk temperature of 39–46 °F (4–8 °C). We would therefore
recommend using a milk cooler or a milk container.
T Remove the protective cover from the fine foam frother.
T Connect the milk pipe to the fine foam frother.
T Connect the other end of the milk pipe to a milk container
or a milk cooler.
Connecting milk
14
1 Preparing and using for the first time
You have the option of connecting your D6 wirelessly to a
compatible accessory. To do this, the JURA Smart Connect must
be plugged into the service socket.
E The Smart Connect can be protected against unauthorized
access using a PIN. Activate the PIN function via the JURA
app. You will find more information at
www.jura.com/smartconnect.
E Please note that you can only connect either the Cool Control
or only one JURA app to the coffee machine via Smart
Connect.
T Position the accessory near the coffee machine (a maximum
of 0.5 m away).
T Switch on the accessory and the coffee machine.
T Press the reset button of the Smart Connect (e.g. with a
paper clip).
T Then (within 30 sec.) press and hold the reset key of the
accessory until the LED lights up to indicate the successful
connection.
Connect accessory (with
wireless connection)
15
2 Preparation
2 Preparation
Hot coffee, hot steam and hot water can cause scalding. Scalding is
a serious burn.
T Use extreme care when handling hot liquid or steam.
T Allow liquid to cool down before drinking.
T In the event of scalding, rinse affected area with cold water
and seek medical attention.
T Keep children AWAY.
Basic information about preparing drinks:
U
During the grinding operation you can select the coffee
strength of single products by turning the Rotary Switch:
MILD, NORMAL, STRONG or EXTRA.
U
During preparation, you can change the preset amounts (e.g.
amount of water or milk foam) by turning the Rotary Switch.
U
You can stop preparation at any time. Just press the Rotary
Switch (for a specialty coffee) or return the switch to its
original position (for milk foam and hot water).
U
The last specialty coffee prepared is always displayed, even if
the D6 was switched off in the meantime.
E The water volume is given as standard in ‘oz’. You can change
this setting to ‘ml’ in programming mode (see Chapter 4
‘Permanent settings in programming mode – Unit for amount
of water’).
Coffee tastes best served hot. A cold porcelain cup cools the
beverage – and impairs the taste. We therefore recommend
prewarming the cups. The full coffee aroma can develop only in
prewarmed cups. You can purchase a JURA cup warmer from your
specialized dealer.
You can make permanent settings for all products in programming
mode (see Chapter 4 ‘Permanent settings in programming mode –
Product settings’).
J WARNING
16
2 Preparation
Espresso and coffee are both prepared following this model.
Example:Proceed as follows to prepare one coffee.
Precondition:
CAPPUCC. is displayed (example).
T Place a cup under the coffee spout.
T Turn the Rotary Switch until
COFFEE is displayed.
T Press the Rotary Switch.
Preparation starts.
COFFEE and the coffee strength are
displayed. The preset amount of water for coffee flows into
the cup.
Preparation stops automatically.
COFFEE appears on the
display.
When you prepare two specialty coffees at once, the amount of
water selected for the single product is used for each cup.
The preparation of twoespressi and twocoffees follows this same
model.
Example:Proceed as follows to prepare two espressi.
Precondition:
CAPPUCC. is displayed (example).
T Place two espresso cups under the coffee spout.
T Turn the Rotary Switch until
ESPRESSO is displayed.
T Press the Rotary Switch twice (within 2seconds) to start
preparation of two espressi.
2CUPS
Preparation starts. The preset amount of water flows into
the cups.
Preparation stops automatically.
ESPRESSO appears on
the display.
Your D6 can prepare a cappuccino at the touch of a button. There is
no need to move the cup.
Precondition:
CAPPUCC. is displayed. Milk is connected to the
fine foam frother.
Espresso and coffee
Two specialty coffees at
the touch of a button
Cappuccino
17
2 Preparation
T Place a cup under the coffee spout and the fine foam frother.
E Ensure that the filling height of the milk is no higher than
the milk pipe connection on the fine foam frother.
T Press the Rotary Switch.
CAPPUCC.
HEATING
As soon as the machine has heated up, OPEN SWITCH
appears, the light segment on the switch lights up.
T Turn the switch to them position.
The milk foam is prepared. Preparation stops automatically
when the preset amount of milk foam is reached.
CLOSE SWITCH
T Turn the switch to the °position.
Coffee preparation starts. The preset amount of water for
espresso flows into the cup.
Preparation stops automatically.
CAPPUCC. appears on
the display.
To ensure that the fine foam frother always works properly,
you must clean it daily when you have been preparing milk (see
Chapter 5 ‘Maintenance – Cleaning the fine foam frother’).
Precondition:
CAPPUCC. is displayed (example). Milk is
connected to the fine foam frother.
T Place a cup under the fine foam frother.
E Ensure that the filling height of the milk is no higher than the
milk pipe connection on the fine foam frother.
T Touch the Milk foam symboln.
HEATING/ MILK
As soon as the machine has heated up, MILK/ READY,
the light segment on the switch lights up.
T Turn the switch to them position.
The milk foam is prepared.
Preparation stops automatically when the preset amount of
milk foam is reached.
Milk foam
18
2 Preparation
T Turn the switch to the °position.
MILK/ READY
E You can continue to prepare milk foam for the next
40 seconds or so without the machine having to heat up
again.
To ensure that the fine foam frother always works properly,
you must clean it daily when you have been preparing milk (see
Chapter 5 ‘Maintenance – Cleaning the fine foam frother’).
It is easy to make permanent settings for the amount of water for all
specialty coffees according to the cup size. Adjust the amount once
as shown in the following example. Every time you prepare a drink
in the future, this amount of water will be dispensed.
The process for permanently adapting the amount of water to the
cup size is the same for all specialty coffees.
Example:Proceed as follows to permanently set the amount of
water for one coffee.
Precondition:
CAPPUCC. is displayed (example).
T Place a cup under the coffee spout.
T Turn the Rotary Switch until
COFFEE is displayed.
T Press and hold the Rotary Switch, until
ENOUGH
COFFEE? appears.
T Release the Rotary Switch.
Preparation starts and the coffee flows into the cup.
T As soon as there is sufficient coffee in the cup, press the
Rotary Switch.
Preparation stops.
OK appears briefly on the display. The set
amount of water for one coffee is permanently stored.
COFFEE appears on the display.
E You can alter this setting at any time by repeating the above
procedure.
E You can also permanently set the amount of water for all
specialty coffees in programming mode (see Chapter 4
‘Permanent settings in programming mode – Product
settings’).
Permanently setting the
amount of water for the
cup size
19
2 Preparation
You can adjust the grinder to suit the degree of roast of your coffee.
If you adjust the consistency of grind when the grinder is not
operating, the grinder adjustment switch could be damaged.
T Only adjust the consistency of grind when the grinder is
running.
The consistency of grind is correct if the coffee flows regularly from
the coffee spout. In addition a fine, thick crema forms.
Example:Proceed as follows to change the consistency of grind
during the preparation of an espresso.
T Place a cup under the coffee spout.
T Open the bean container cover and remove the aroma
preservation cover.
T Turn the Rotary Switch until
ESPRESSO is displayed.
T Press the Rotary Switch to start preparation.
T Turn the grinder adjustment switch to the desired position
while the grinder is running.
The preset amount of water flows into the cup. Preparation
stops automatically.
There is a danger of scalding from hot water splashes.
T Avoid direct contact with the skin.
Example:Proceed as follows to prepare hot water.
Precondition:
CAPPUCC. is displayed (example).
T Place a cup under the fine foam frother.
T Turn the switch to them position.
WATER, water flows out of the fine foam frother.
Preparation stops automatically when the preset amount of
water is reached.
T Turn the switch to the °position.
CAPPUCC. appears on the display (example).
Adjusting the grinder
NOTICE
Hot water
J
CAUTION
20
3 Daily operation
3 Daily operation
Daily maintenance of the machine and hygiene when handling milk,
coffee and water are key to a perfect coffee result in the cup every
time. You should therefore change the water daily.
Milk, sparkling mineral water or other liquids can damage the water
tank or the machine.
T Only fill the water tank with fresh, cold water.
T Open the water tank cover.
T Remove the water tank and rinse it with cold water.
T Fill the water tank with fresh, cold water and reinsert the
tank.
T Close the water tank cover.
T Place a receptacle under the coffee spout.
T Press the On/Off button Q to switch the D6 on.
HEATING
RINSING, the system is rinsed. The rinse stops
auto mati cally.
CAPPUCC. appears on the display
(example). Your D6 is ready for use.
To ensure that you get many years of reliable service out of your D6
and to guarantee the optimum coffee quality, the machine requires
daily maintenance.
T Pull out the drip tray.
T Empty the coffee grounds container and the drip tray. Rinse
them both with warm water.
E Always empty the coffee grounds container when the machine
is switched on. This is the only way of resetting the coffee
grounds counter.
T Refit the coffee grounds container and the drip tray.
Filling the water tank
NOTICE
Switching on
Daily maintenance
21
3 Daily operation
T Rinse the water tank with clean water.
T Clean the fine foam frother (see Chapter 5 ‘Maintenance –
Cleaning the fine foam frother’).
T Remove the milk pipe and rinse it thoroughly under running
water.
T Dismantle and rinse the fine foam frother (see Chapter 5
‘Maintenance – Dismantling and rinsing the fine foam
frother’).
T Wipe the surface of the machine with a clean, soft, damp
cloth (e.g. microfiber cloth).
Carry out the following maintenance actions regularly or as
required:
U
In the interests of hygiene, we recommend changing the milk
pipe and interchangeable milk spout on a regular basis
(approximately every 3 months). Replacements are available
from specialized dealers.
U
Clean the inside of the water tank, e.g. with a brush. Further
information about the water tank is provided in these
instructions for use (see Chapter 5 ‘Maintenance – Descaling
the water tank’).
U
Traces of milk and coffee may stick to the top and bottom of
the cup platform. If this happens, clean the cup platform.
When the D6 is switched off, the system is automatically rinsed if a
specialty coffee has been prepared. If milk has been prepared, you
will also be prompted to clean the milk system.
T Place a receptacle under the fine foam frother and under the
coffee spout.
T Press the On/Off button Q.
E If milk has been prepared, you will be prompted to clean the
milk system (
CLEAN MILK?). You can start milk system
cleaning by pressing the Rotary Switch. After 10seconds the
switch-off process continues automatically.
If milk has been prepared but you have not started milk
system cleaning, you will be prompted to carry out milk
system rinsing first (
M-RINSE).
OPEN SWITCH
Regular maintenance
Switching off the
machine
22
3 Daily operation
T Turn the switch to them position.
nnnkkkkk, the milk system is rinsed.
The rinse stops automatically.
CLOSE SWITCH
T Turn the switch to the °position.
RINSING, the system rinses itself. The rinse stops
automatically. Your D6 is switched off.
23
4 Permanent settings in programming mode
4 Permanent settings in programming mode
Hot coffee, hot steam and hot water can cause scalding. Scalding is
a serious burn.
T Use extreme care when handling hot liquid or steam.
T Allow liquid to cool down before drinking.
T In the event of scalding, rinse affected area with cold water an
seek medical attention.
T Keep children AWAY.
You can make permanent settings in programming mode. You can
navigate through the program items and permanently save the
required settings simply by turning and pressing the Rotary Switch.
You can make the following settings with the Rotary Switch:
Program item Sub-item Explanation
RINSE M-RINSE,
M-CLEAN,
RINSE,
CLEAN,
DESCALE
T Select the desired maintenance program.
BUTTONS
T Select your settings for specialty coffees.
HARDNESS 1°dH–30°dH
T You can set the water hardness of the water used.
OFF FROM 15MIN., 30MIN.,
1HRS.–9HRS.
T Set the time after which the D6 should switch off
automatically.
UNITS ML, OZ
T Select the unit for the amount of water.
LANGUAGE
T Select your language.
EXIT
T Exit programming mode.
E You can exit programming mode directly at any time. Simply
touch the P symbol for approximately 2 seconds.
J WARNING
24
4 Permanent settings in programming mode
Hot coffee, hot steam and hot water can cause scalding. Scalding is
a serious burn.
T Use extreme care when handling hot liquid or steam.
T Allow liquid to cool down before drinking.
T In the event of scalding, rinse affected area with cold water an
seek medical attention.
T Keep children AWAY.
In the program item
BUTTONS you can make individual,
permanent settings for all products:
Product Amount Coffee strength Temperature
Cappuccino
Water:
0.5 OZ – 8.0 OZ
(25 ml – 240 ml)
Milk foam:
3SEC.–60SEC.
MILD, NORMAL,
STRONG, EXTRA
NORMAL,
HIGH
Espresso
Water:
0.5 OZ – 2.5 OZ
(15 ml – 80 ml)
MILD, NORMAL,
STRONG, EXTRA
NORMAL,
HIGH
Coffee
Water: 0.5 OZ – 8.0 OZ
(25 ml – 240 ml)
MILD, NORMAL,
STRONG, EXTRA
NORMAL,
HIGH
Milk foam
Milk foam:
3SEC.–60SEC.
– –
Hot water
Water:
0.5 OZ – 15.0 OZ
(25 ml – 450 ml)
– –
2 cups When you prepare two specialty coffees at once, the temperature and amount
of water selected for the single product are used for each cup.
Permanent settings in programming mode always follow the same
model.
Example:Proceed as follows to change the coffee strength for one
coffee from
NORMAL to STRONG.
Precondition:
CAPPUCC. is displayed (example).
T Touch the P symbol for approximately 2 seconds until
RINSE appears on the display.
T Turn the Rotary Switch until
BUTTONS is displayed.
T Press the Rotary Switch to enter the program item.
ESPRESSO
Product settings
J WARNING
25
4 Permanent settings in programming mode
T Turn the Rotary Switch until COFFEE is displayed.
T Press the Rotary Switch.
VOLUME
T Turn the Rotary Switch until STRENGTH is displayed.
T Press the Rotary Switch.
NORMAL
T Turn the Rotary Switch until STRONG is displayed.
T Press the Rotary Switch to confirm the setting.
OK appears briefly on the display.
STRENGTH
T Turn the Rotary Switch until EXIT is displayed.
T Press the Rotary Switch to exit the program item.
COFFEE
T Touch the P symbol to exit programming mode.
CAPPUCC. (example)
The harder the water is, the more frequently the D6 needs to be
descaled. It is therefore important to set the water hardness
accurately.
The water hardness was set when the machine was first used. You
can change this setting at any time.
The water hardness can be adjusted on a continuous scale between
1
°dH and 30°dH.
Precondition:
CAPPUCC. is displayed (example).
T Touch the P symbol for approximately 2 seconds until
RINSE appears on the display.
T Turn the Rotary Switch until
HARDNESS is displayed.
T Press the Rotary Switch to enter the program item.
16°dH
T Turn the Rotary Switch to change the setting.
T Press the Rotary Switch to confirm the setting.
OK appears briefly on the display.
HARDNESS
T Touch the P symbol to exit programming mode.
CAPPUCC. (example)
Setting the water
hardness
26
4 Permanent settings in programming mode
By instructing your D6 to automatically switch itself off, you can cut
down your energy consumption. If this function is activated, your
D6 switches off automatically after the preset time following the
last action on the machine.
You can set the automatic switch-off to 15minutes, 30minutes or
1–9hours.
Precondition:
CAPPUCC. is displayed (example).
T Touch the P symbol for approximately 2 seconds until
RINSE appears on the display.
T Turn the Rotary Switch until
OFF FROM is displayed.
T Press the Rotary Switch to enter the program item.
30MIN.
T Turn the Rotary Switch to change the setting.
T Press the Rotary Switch to confirm the setting.
OK appears briefly on the display.
OFF FROM
T Touch the P symbol to exit programming mode.
CAPPUCC. (example)
In the program item
UNITS you can set the unit used for the
amount of water.
Example:Proceed as follows to change the unit for the amount of
water from
ML to OZ.
Precondition:
CAPPUCC. is displayed (example).
T Touch the P symbol for approximately 2 seconds until
RINSE appears on the display.
T Turn the Rotary Switch until
UNITS is displayed.
T Press the Rotary Switch to enter the program item.
ML
T Turn the Rotary Switch until OZ is displayed.
T Press the Rotary Switch to confirm the setting.
OK appears briefly on the display.
UNITS
T Touch the P symbol to exit programming mode.
CAPPUCC. (example)
Automatic switch-off
Unit for amount of water
27
4 Permanent settings in programming mode
In the program item LANGUAGE you can set the language used
by your D6.
Example:Proceed as follows to change the language from
EN to
FR.
Precondition:
CAPPUCC. is displayed (example).
T Touch the P symbol for approximately 2 seconds until
RINSE appears on the display.
T Turn the Rotary Switch until
LANGUAGE is displayed.
T Press the Rotary Switch to enter the program item.
EN
T Turn the Rotary Switch until FR is displayed.
T Press the Rotary Switch to confirm the setting.
OK appears briefly on the display.
LANGUE
T Touch the P symbol to exit programming mode.
CAPPUCC. (example)
Language
28
5 Maintenance
5 Maintenance
Use of maintenance products that are harmful to health and
discharge of liquids during maintenance program. Harmful if
swallowed. Irritating to eyes and skin.
T Keep children AWAY.
T Keep children away from the machine while it is performing a
maintenance program.
T Avoid contact with skin and eyes.
T Avoid generation of dust. Do not inhale dust.
T When using do not eat or drink.
T Keep maintenance products away from food, drink and
animal food.
T Keep container tightly closed and dry. Keep in a cool place.
Your D6 has the following integrated maintenance programs:
U
Cleaning the fine foam frother (M-CLEAN)
U
Cleaning the machine (CLEAN)
U
Descaling the machine (DESCALE)
E Proceed with the maintenance programs when prompted to
do so.
E You can start the maintenance programs at any time in
programming mode (program item
RINSE).
Ten minutes after milk preparation, the D6 prompts you to perform
milk system rinsing.
Precondition:
M-RINSE/ CAPPUCC. is displayed (example).
T Place a receptacle under the fine foam frother.
T Touch the Maintenance symbol c for approximately
2 seconds until
OPEN SWITCH appears.
T Turn the switch to them position.
The fine foam frother is rinsed.
CLOSE SWITCH
T Turn the switch to the °position.
CAPPUCC. (example)
J WARNING
Rinsing the fine foam
frother
29
5 Maintenance
To ensure that the fine foam frother always works properly, you
must clean it daily when you have been preparing milk
Non-recommended cleaning agents will not optimally remove milk
residues. This may cause the cappuccino frother to become blocked
and fly off the machine. Discharge of hot steam.
T Use only original JURA milk system cleaner.
Harmful and irritating cleaning agent. Harmful if swallowed.
Irritating to eyes and skin.
T Keep children AWAY.
T Avoid contact with skin and eyes.
T After contact with skin, wash immediately with plenty of
water. In case of skin irritation, seek medical advice.
T After eye contact, immediately flush eyes with plenty of water
and seek medical advice.
T If swallowed, rinse mouth immediately and drink large
quantities of water. Do not induce vomiting. Seek medical
advice immediately and show label.
E JURA milk system cleaner is available from specialized dealers.
Precondition:
CAPPUCC. is displayed (example).
T Touch the P symbol for approximately 2 seconds until
RINSE appears on the display.
T Press the Rotary Switch to enter the program item.
M-RINSE
T Turn the Rotary Switch until M-CLEAN is displayed.
T Press the Rotary Switch.
CLEANER / WATER
T Remove the milk pipe from the milk container or milk cooler.
T Pour 8.5 oz (250 ml) of fresh water into a receptacle and
add 1 capful of milk system cleaner.
T Immerse the milk pipe in the receptacle.
T Place a receptacle under the fine foam frother.
T Press the Rotary Switch.
M-CLEAN, OPEN SWITCH, the light segment on the
switch lights up.
T Turn the switch to them position.
The fine foam frother and the milk pipe are cleaned.
CLOSE SWITCH
Cleaning the fine foam
frother
J WARNING
J WARNING
30
5 Maintenance
T Turn the switch to the °position.
WATER
T Rinse the receptacle thoroughly, fill it with 8.5 oz (250ml) of
fresh water and immerse the milk pipe in the water.
T Empty the other receptacle and place it under the fine foam
frother once more.
T Press the Rotary Switch.
OPEN SWITCH
T Turn the switch to them position.
The fine foam frother and the milk pipe are rinsed with fresh
water.
CLOSE SWITCH
T Turn the switch to the °position.
CAPPUCC. (example)
To make sure the fine foam frother works properly, and in the
interests of hygiene, it must be dismantled and rinsed daily if you
have been preparing milk. Your D6 will not prompt you to
dismantle and rinse the frother.
T Remove the milk pipe and rinse it thoroughly under running
water.
T Carefully remove the fine foam frother from the Connector
System
©
by twisting slightly.
T Dismantle the fine foam frother into its individual parts.
T Rinse all the parts under running water. If there are severely
dried-on milk residues, firstly immerse the individual parts
in a solution of 8.5 oz (250ml) cold water and 1 capful of JURA
milk system cleaner. Then rinse the parts thoroughly.
T Re-assemble the fine foam frother.
E Ensure that all individual parts are correctly and firmly
connected to ensure optimum operation.
T Firmly attach the fine foam frother to the Connector
System
©
.
Dismantling and rinsing
the fine foam frother
31
5 Maintenance
Your D6 no longer has to be descaled if you are using the CLEARYL
Smart filter cartridge.
E Once the filter cartridge stops working (depending on the
water hardness setting), the D6 will prompt you to change the
filter.
E CLEARYL Smart filter cartridges are available from specialized
dealers.
Precondition:
FILTER/ CAPPUCC. is displayed (example).
T Open the water tank cover.
T Remove and empty the water tank.
T Open the filter holder and remove the old CLEARYL Smart
filter cartridge.
T Insert a new CLEARYL filter cartridge Smart into the water
tank, exerting slight pressure.
T Close the filter holder. It will click into place audibly.
T Fill the water tank with fresh, cold water and reinsert the
tank.
The machine has automatically detected that you have just
inserted/changed the filter cartridge.
OPEN SWITCH, the light segment on the switch lights up.
T Place a receptacle under the fine foam frother.
T Turn the switch to them position.
FILTER RINSING, water flows out of the fine foam
frother.
Rinsing of the filter stops automatically.
CLOSE SWITCH
T Turn the switch to the °position.
CAPPUCC. (example)
Inserting/changing the
filter
32
5 Maintenance
After 180preparations or 80switch-on rinses, the D6 will prompt
you to clean it.
Non-recommended (e.g. liquid) cleaning agents may contain
substances that could damage the machine or leave residues.
T Use only original JURA cleaning tablets. These are specially
formulated for your machine.
Harmful and irritating cleaning agent. Harmful if swallowed.
Irritating to eyes and skin.
T Keep children AWAY.
T Avoid contact with skin and eyes.
T Avoid generation of dust. Do not inhale dust.
T After contact with skin, wash immediately with plenty of
water. In case of skin irritation, seek medical advice.
T After eye contact, immediately flush eyes with plenty of water
and seek medical advice.
T If swallowed, rinse mouth immediately and drink large
quantities of water. Do not induce vomiting. Seek medical
advice immediately and show label.
E The cleaning program lasts approximately 20 minutes.
E Do not interrupt the cleaning program. The quality of cleaning
will be impaired if you do so.
E JURA cleaning tablets are available from specialized dealers.
Precondition:
CLEAN/ CAPPUCC. is displayed (example).
T Touch the Maintenance symbolc for approximately
2 seconds.
EMPTY TRAY appears on the display.
T Empty the drip tray and coffee grounds container and put
them back into the machine.
PRESS RINSE
T Place a receptacle under the coffee spout.
T Touch the Maintenance symbolc.
CLEANING, water flows out of the coffee spout.
The operation is interrupted,
ADD TABLET.
T Open the cover of the filler funnel for the cleaning tablet.
Cleaning the machine
J WARNING
J WARNING
33
5 Maintenance
T Insert a JURA cleaning tablet into the filler funnel.
T Close the cover of the filler funnel.
T Touch the Maintenance symbolc.
CLEANING, water flows out of the coffee spout several
times.
The operation stops automatically.
EMPTY TRAY
T Empty the drip tray and coffee grounds container and put
them back into the machine.
CAPPUCC. (example)
The D6 builds up deposits of limescale over time and automatically
prompts you to descale it when necessary. The degree of
calcification depends on the hardness of your water.
Non-recommended descaling agents (e.g. vinegar) may contain
substances that could damage the machine or leave residues.
T Use only original JURA descaling tablets. These are specially
formulated for your machine.
Harmful and irritating descaling agent. Harmful if swallowed.
Irritating to eyes and skin.
T Keep children AWAY.
T Avoid contact with skin and eyes.
T Avoid generation of dust. Do not inhale dust.
T After contact with skin, wash immediately with plenty of
water. In case of skin irritation, seek medical advice.
T After eye contact, immediately flush eyes with plenty of water.
Remove contact lenses. Seek medical advice.
T If swallowed, rinse mouth immediately and drink large
quantities of water. Do not induce vomiting. Seek medical
advice immediately and show label.
If the descaling operation is interrupted, there may be damage to
the machine.
T Allow the descaling program to run to the end.
E The descaling program lasts approximately 45minutes.
E JURA descaling tablets are available from specialized dealers.
Descaling the machine
J WARNING
J WARNING J WARNING
NOTICE
34
5 Maintenance
E If the descaling agent comes into contact with sensitive
surfaces (e.g. marble), damage cannot be ruled out. Clean up
any splashes immediately.
Precondition:
DESCALE/ CAPPUCC. is displayed (example).
T Touch the Maintenance symbolc for approximately
2 seconds.
EMPTY TRAY appears on the display.
T Empty the drip tray and coffee grounds container and put
them back into the machine.
AGENT IN TANK
T Remove and empty the water tank.
T Completely dissolve 3JURA descaling tablets in a receptacle
holding 17 oz (500 ml) of water. This may take several
minutes.
T Pour the solution into the empty water tank and insert it
into the machine.
OPEN SWITCH, the light segment on the switch lights up.
T Place a receptacle under the fine foam frother.
T Turn the switch to them position.
DESCALE appears and water flows out of the fine foam
frother repeatedly. The Maintenance symbol c flashes
during the descaling operation.
The operation is interrupted,
CLOSE SWITCH.
T Turn the switch to the °position.
DESCALE. The descaling operation is continued.
The operation is interrupted,
EMPTY TRAY.
T Empty the drip tray and coffee grounds container and put
them back into the machine.
FILL TANK
T Empty the receptacle and place it under the coffee spout
and fine foam frother.
T Remove the water tank and rinse it thoroughly.
T Fill the water tank with fresh, cold water and reinsert the
tank.
OPEN SWITCH, the light segment on the switch lights up.
T Turn the switch to them position.
DESCALE
The operation is interrupted, CLOSE SWITCH.
35
5 Maintenance
T Turn the switch to the °position.
DESCALE
The operation is interrupted, DESCALE.
Water flows out of the coffee spout.
EMPTY TRAY
T Empty the drip tray and coffee grounds container and put
them back into the machine.
CAPPUCC. (example)
E If the descaling operation stops unexpectedly, rinse the water
tank thoroughly.
Coffee beans may be covered with a slight oil film which remains on
the walls of the bean container. These traces may negatively affect
the coffee result. For this reason clean the bean container from time
to time.
Precondition:
FILL BEANS is displayed.
T Press the On/Off button Q to switch the D6 off.
T Open the bean container cover and remove the aroma
preservation cover.
T Clean the bean container with a soft, dry cloth.
T Fill the bean container with coffee beans and close the
aroma preservation cover.
T Close the bean container cover.
Limescale deposits may form in the water tank. To ensure correct
function of the machine, descale the water tank from time to time.
T Remove the water tank.
T If you use a CLEARYL Smart filter cartridge, remove this.
T Completely fill the water tank and dissolve 3 JURA descaling
tablets in it.
T Leave the water tank with the descaling solution for several
hours (e.g. overnight).
T Empty the water tank and rinse it thoroughly.
T If you use a CLEARYL Smart filter cartridge, insert this again.
T Fill the water tank with fresh, cold water and reinsert the
tank.
Cleaning the bean
container
Descaling the water tank
36
6 Display messages
6 Display messages
Message Cause/Result Action
FILL TANK
The water tank is empty. You
cannot prepare any products.
T Fill the water tank (see Chapter 3
‘Daily operation – Filling the water
tank’).
EMPTY TRAY
The drip tray is full. No specialty
coffees can be prepared. You
can prepare hot water and milk
foam.
T Empty the coffee grounds
container and the drip tray (see
Chapter 3 ‘Daily operation – Daily
maintenance’).
TRAY MISSING
The drip tray is not inserted
correctly or is not inserted at
all. You cannot prepare any
products.
T Fit the drip tray.
FILL BEANS
The bean container is empty.
No specialty coffees can be
prepared. You can prepare hot
water and milk foam.
T Fill the bean container (see Chap-
ter 1 ‘Preparing and using for the first
time – Filling the bean container’).
T Press the Rotary Switch to confirm
that the bean container has been
filled.
PRESS RINSE
The D6 is prompting you to
continue a previously started
maintenance program.
T Touch the Maintenance symbol c
to continue the program.
FILTER/
CAPPUCC.
(example)
The filter cartridge no longer
works.
T Replace the CLEARYL Smart filter
cartridge (see Chapter 5
‘Maintenance – Inserting/changing
the filter’).
CLEAN/
CAPPUCC.
(example)
The D6 is prompting you to
clean it.
T Perform cleaning (see Chapter 5
‘Maintenance – Cleaning the
machine’).
DESCALE/
CAPPUCC.
(example)
The D6 is prompting you to
descale it.
T Perform descaling (see Chapter 5
‘Maintenance – Descaling the
machine ’).
TOO HOT
The system is too hot to start a
maintenance program.
T Wait for several minutes until
the system has cooled or prepare a
specialty coffee or hot water.
37
7 Troubleshooting
7 Troubleshooting
Problem Cause/Result Action
Insufficient foam is
produced when the milk
is frothed or milk
sprays out of the fine
foam frother.
The fine foam frother is
dirty.
T Clean the fine foam frother (see Chap-
ter 5 ‘Maintenance – Cleaning the fine
foam frother’).
T Dismantle and rinse the fine foam
frother (see Chapter 5 ‘Maintenance –
Dismantling and rinsing the fine foam
frother’).
Coffee only comes out
in drips when it is being
prepared.
The coffee is ground too
finely and obstructs the
system.
T Set the grinder to a coarser setting
(see Chapter 2 ‘Preparation – Adjusting
the grinder’).
The water hardness may
not have been correctly
set.
T Perform descaling (see Chapter 5
‘Maintenance – Descaling the machine ’).
FILL TANK is
displayed although the
water tank is full.
The water tank float is
trapped.
T Descale the water tank (see Chapter 5
‘Maintenance – Descaling the water
tank’).
Grinder is making a very
loud noise.
There are foreign objects
in the grinder.
T Contact customer support in your
country (see Chapter 11 ‘JURA contact
details/ Legal information’).
ERROR2 or ERROR5
is displayed.
If the machine has been
exposed to the cold for a
long period of time,
heating may be disabled
for safety reasons.
T Warm the machine at room tempera-
ture.
Other
ERROR mes-
sages are displayed.
–
T Switch the machine off with the On/Off
button Q. Contact customer support in
your country (see Chapter 11 ‘JURA contact
details/ Legal information’).
E If you were unable to solve the problem, contact customer
support in your country (see Chapter 11 ‘JURA contact details/
Legal information’).
38
8 Transport and environmentally friendly disposal
8 Transport and environmentally friendly disposal
Keep the packaging for your D6. It should be used to protect the
machine during transport.
In order to protect the D6 from frost during transport, the system
must be emptied.
Precondition:
CAPPUCC. is displayed (example).
T Remove the milk pipe from the fine foam frother.
T Place a receptacle under the fine foam frother.
T Touch the Milk foam symboln.
HEATING/ MILK
As soon as the machine has heated up, MILK/ READY
appears, the light segment on the switch lights up.
T Turn the switch to them position.
MILK, hot steam is discharged from the fine foam frother.
T Remove and empty the water tank.
T Change the time to
60SEC..
Steam will continue to be discharged from the fine foam
frother until the system is empty.
CLOSE SWITCH
T Turn the switch to the °position.
FILL TANK
T Press the On/Off button Q.
Your D6 is switched off.
Please dispose of old machines in an environmentally neutral way.
H
Transport/ Emptying the
system
Disposal
39
9 Technical data
9 Technical data
Voltage 120V~, 60Hz
Power 1450W
Conformity mark
Pump pressure static, max. 15bar
Holding capacity of water tank 64 oz (1.9 l)
Holding capacity of bean container 7 oz (200 g)
Holding capacity of coffee grounds
container
max. 16 portions
Cord length approx. 47 in.
(approx. 1.2 m)
Weight approx. 18 lb
(approx. 8.7 kg)
Dimensions (W×H×D) 11 × 13.6 × 16.3 in.
(28 × 34.5 × 41.5cm)
The machine complies with the following directives:
U
Standard UL 1082
U
Canadian Standard CSA C22.2 No. 64
Directives
40
10 Index
10 Index
A
Addresses 44
Aroma preservation cover
Bean container with aroma preservation
cover 8
Automatic switch-off 26
B
Bean container
Bean container with aroma preservation
cover 8
Cleaning 35
Filling 10
Bus bar
Technical data 39
Button
On/Off button 8
C
Cappuccino 16
Cleaning
Bean container 35
Fine foam frother 29
Machine 32
CLEARYL Smart filter cartridge
Changing 31
Inserting 31
Coffee 16
Coffee grounds container 8
Coffee spout
Height-adjustable coffee spout 8
Connect accessory 14
Consistency of grind
Adjusting the grinder 19
Grinder adjustment switch 8
Contact details 44
Cover
Bean container 8
Filler funnel for cleaning tablet 8
Water tank 8
Cup platform 8
Customer support 44
D
Daily maintenance 20
Descaling
Machine 33
Water tank 35
Display 9
Display messages 36
Disposal 38
Double product 16
Drip tray 8
E
Emptying the system 38
Errors
Troubleshooting 37
Espresso 16
F
Filler funnel
Filler funnel for cleaning tablet 8
Filling
Bean container 10
Water tank 20
Filter
Changing 31
Inserting 31
Fine foam frother 8
Cleaning 29
Dismantling and rinsing 30
Rinsing 28
First-time use 11
G
Grinder adjustment switch 8
H
Height-adjustable coffee spout 8
Homepage 10
Hotline 44
Hot water 19
Hot water and milk foam preparation
Switch for hot water and milk foam
preparation 8
41
10 Index
I
Important safeguards
Safety 4
Internet 10
J
JURA
Contact details 44
Internet 10
L
Language 27
M
Machine
Cleaning 32
Daily maintenance 20
Descaling 33
Regular maintenance 21
Setting up 10
Switching off 21
Switching on 20
Maintenance 28
Daily maintenance 20
Regular maintenance 21
Messages, display 36
Milk
Connecting milk 13
Milk foam 17
Milk system
Cleaning the fine foam frother 29
Rinsing the fine foam frother 28
P
Permanently setting the water for the cup
size 18
Permanent settings in programming mode
23
Power cord 8
Preparation 15
Cappuccino 16
Coffee 16
Espresso 16
Hot water 19
Milk foam 17
Two specialty coffees 16
Problems
Troubleshooting 37
Product settings 24
Programming mode 23
Automatic switch-off 26
Language 27
Product settings 24
Setting the water hardness 25
Unit for amount of water 26
R
Regular maintenance 21
Rinsing
Fine foam frother 28
Rotary Switch 9
S
Safety
Important safeguards 4
Service socket 9
Settings
Permanent settings in programming
mode 23
Setting up
Setting up the machine 10
Smart Connect 9, 14
Switch for hot water and milk foam prepara-
tion 8
Switching off 21
Switching on
Machine 20
Switch-off
Automatic switch-off 26
Symbol
Maintenance 9
Milk foam 9
P (programming) 9
Symbol description 3
T
Technical data 39
Tel 44
Transport 38
Troubleshooting 37
Two products 16
U
Unit for amount of water 26
Use, First-time 11
42
10 Index
W
Water hardness
Determining the water hardness 11
Setting the water hardness 25
Water tank 8
Descaling 35
Filling 20
Website 10
Wireless connection 14
43
44
11 JURA contact details/ Legal information
11 JURA contact details/ Legal information
JURA Elektroapparate AG
Kaffeeweltstrasse 10
CH-4626 Niederbuchsiten
Switzerland
USA: JURA Inc.
Canada: FAEMA
Customer Service
Phone
E-Mail
1-800-220-5701
1-(855)-544-8600
info@juracanada.ca
Opening Hours (EST) Mon – Thu 9 am – 9 pm,
Fri 9 am – 8 pm,
Sat 9 am – 5 pm
Distributor Address
Phone
Fax
20 Craig Road
Montvale, NJ 07645
001 (201) 767-3999
001 (201) 767-9684
115 Matheson Boulevard East
Mississauga, Ontario, L4Z 1X8
1-(905)-501-8600
Internet www.us.jura.com www.ca.jura.com
@ You will find additional contact details for your country at
www.jura.com.
We reserve the right to make technical changes. The diagrams used
in these instructions for use are for illustration purposes only and do
not represent the original colors of the machine. Some details of
your D6 may vary.
Your opinion is important to us! Use the contact details at
www.jura.com.
The instructions for use contain information which is protected by
copyright. It is not permitted to photocopy these instructions for use
or translate them into another language without the prior written
consent of JURA Elektroapparate AG.
Technical changes
Feedback
Copyright
J73908/D6/US-en/20180731
