Loading ...
Loading ...
Loading ...
is not visible on compatible fēnix devices while the heart rate
monitor is underwater.
You must start a timed activity on your paired fēnix device to
view stored heart rate data later. During rest intervals when out
of the water, the heart rate monitor sends your heart rate data to
your fēnix device.
Your fēnix device automatically downloads stored heart rate
data when you save your timed swim activity. Your heart rate
monitor must be out of the water, active, and within range of the
device (3 m) while data is downloaded. You can review your
heart rate data in the device history and on your Garmin
Connect account.
Data Storage
The heart rate monitor can store up to 20 hours of data in a
single activity. When the heart rate monitor memory is full, your
oldest data is overwritten.
You can start a timed activity on your paired fēnix device, and
the heart rate monitor records your heart rate data even if you
move away from your device. For example, you can record heart
rate data during fitness activities or team sports where watches
cannot be worn. Your heart rate monitor automatically sends
your stored heart rate data to your fēnix device when you save
your activity. Your heart rate monitor must be active and within
range (3 m) of the device while data is uploaded.
Tips for Erratic Heart Rate Data
If the heart rate data is erratic or does not appear, you can try
these tips.
• Reapply water to the electrodes and contact patches (if
applicable).
• Tighten the strap on your chest.
• Warm up for 5 to 10 minutes.
• Follow the care instructions (Caring for the Heart Rate
Monitor, page 6).
• Wear a cotton shirt or thoroughly wet both sides of the strap.
Synthetic fabrics that rub or flap against the heart rate
monitor can create static electricity that interferes with heart
rate signals.
• Move away from sources that can interfere with your heart
rate monitor.
Sources of interference may include strong electromagnetic
fields, some 2.4 GHz wireless sensors, high-voltage power
lines, electric motors, ovens, microwave ovens, 2.4 GHz
cordless phones, and wireless LAN access points.
Caring for the Heart Rate Monitor
NOTICE
A buildup of sweat and salt on the strap can decrease the ability
of the heart rate monitor to report accurate data.
• Rinse the heart rate monitor after every use.
• Hand wash the heart rate monitor after every seven uses or
one pool swim, using a tiny amount of mild detergent, such
as dishwashing liquid.
NOTE: Using too much detergent may damage the heart rate
monitor.
• Do not put the heart rate monitor in a washing machine or
dryer.
• When drying the heart rate monitor, hang it up or lay it flat.
Running Dynamics
You can use your compatible fēnix device paired with the
HRM-Tri accessory or other running dynamics accessory to
provide real-time feedback about your running form. If your fēnix
device was packaged with the HRM-Tri accessory, the devices
are already paired.
The running dynamics accessory has an accelerometer that
measures torso movement in order to calculate six running
metrics.
Cadence: Cadence is the number of steps per minute. It
displays the total steps (right and left combined).
Vertical oscillation: Vertical oscillation is your bounce while
running. It displays the vertical motion of your torso,
measured in centimeters.
Ground contact time: Ground contact time is the amount of
time in each step that you spend on the ground while
running. It is measured in milliseconds.
NOTE: Ground contact time and balance are not available
while walking.
Ground contact time balance: Ground contact time balance
displays the left/right balance of your ground contact time
while running. It displays a percentage. For example, 53.2
with an arrow pointing left or right.
Stride length: Stride length is the length of your stride from one
footfall to the next. It is measured in meters.
Vertical ratio: Vertical ratio is the ratio of vertical oscillation to
stride length. It displays a percentage. A lower number
typically indicates better running form.
Training with Running Dynamics
Before you can view running dynamics, you must put on a
running dynamics accessory, such as the HRM-Tri accessory,
and pair it with your device (Pairing ANT+ Sensors, page 24).
If your fēnix 5/5S was packaged with the accessory, the devices
are already paired, and the fēnix 5/5S is set to display running
dynamics data screens.
1
Select an option:
• If your running dynamics accessory and fēnix 5/5S device
are already paired, skip to step 7.
• If your running dynamics accessory and fēnix 5/5S device
are not already paired, complete all the steps in this
procedure.
2
Hold MENU.
3
Select Settings > Activities & Apps.
4
Select an activity.
5
Select the activity settings.
6
Select Data Screens > Add New.
7
Select a running dynamics data screen.
NOTE: The running dynamics screens are not available for
all activities.
8
Go for a run (Starting an Activity, page 2).
9
Select UP or DOWN to open a running dynamics screen to
view your metrics.
Color Gauges and Running Dynamics Data
The running dynamics screens display a color gauge for the primary metric. You can display cadence, vertical oscillation, ground
contact time, ground contact time balance, or vertical ratio as the primary metric. The color gauge shows you how your running
dynamics data compare to those of other runners. The color zones are based on percentiles.
Garmin has researched many runners of all different levels. The data values in the red or orange zones are typical for less
experienced or slower runners. The data values in the green, blue, or purple zones are typical for more experienced or faster
runners. More experienced runners tend to exhibit shorter ground contact times, lower vertical oscillation, lower vertical ratio, and
6 Heart Rate Features
Loading ...
Loading ...
Loading ...