Loading ...
Loading ...
Loading ...
8
IMPORTANT: ALLOWING THE AMPLIFIER TO OPERATE WITH ONE OR
MORE CHANNELS IN PROTECT MODE FOR AN EXTENDED PERIOD OF
TIME CAN DAMAGE THE AMPLIFIER.
Protection Circuitry and LEDs
TheSonampampliershaveamulti-stageprotectionsystemto
preventdamagetoyouramplierandspeakers.
Amplier Channel Protection DSP 2-150 MKII
If a channel encounters a short-circuit (in bridge mode the
protection circuitry will sense a short circuit across both positive
speaker terminals), or extremely low impedance will cause the
aectedchanneloutputstoautomaticallymute.Theoutputof
theaectedchannelwillremainmuteduntilthefaulthasbeen
corrected.Onlytheaectedchannelsoutputwillmute,allother
channels will continue to operate normally.
Amplier Channel Protection Indication DSP 2-150 MKII
OnthefrontpaneloftheSonampDSP2-150MKIIampliersare
dual color LEDs that illuminate to indicate the current operating
statusofeachamplierchannel.
When the LED blinks red this is an indication that the channel is
being over driven.
WhentheLEDlightsaresolidredthisisanindicationtheamplier
is in protect mode. While in protect mode the LED lights will
periodically light green to retest the output to determine if the short
has been removed. Protect mode could be caused by a short in
thewire,overheatingoftheamplierorpossiblyaninternalproblem
withtheamplier.
Iftheampliersensesaverylowimpedanceorashortonits
outputs, then it will mute its output and the protection LEDs will
turn red. The output will remain muted until the fault is cleared.
Check the rear panel block connector for shorted wire strands
or reduce the number of speakers connected in parallel to the
amplieroutputs.Sonanceampliersareratedfora4ohmloador
higher, such as two pair of eight ohm speakers.
Rack Ear Installation DSP 2-150 MKII
The DSP 2-150 MKII ships with two long rack ears for when the
amplieristobeusedaloneina1Uspace.Unscrewthefour
Phillips head screws (M4 x 0.7 pitch x 10mm long) found on each
sideoftheleftandrightforwardsectionofamplier.Usethese
screwstoconnecttheincludedrackearstotheamplier
(see Figure 15).
MKII
Figure15:RackEarInstallationDSP2-150MKII
Side View Right
Front View
Amplier Stacking
The DSP 2-150 MKII is capable of being directly stacked with the
feet removed for use in low to moderate output applications (see
Figure 16). For high-output applications, it is recommended to leave
atleast1Uspacebetweenampliersforincreasedventilation.
Itisnotrecommendedtostackmorethanthreeampliershigh
without spacing.
To place two Sonamp 2-100 or DSP 2-150 MKII in a single rack
unitorder:RackMountBracketforSonamp2-100&DSP2-150
MKII SKU# 93098 (see Figure 17).
MKII
MKII
MKII
1L 1R
2-100
MKII
Figure16:StackedCongurationDSP2-150MKIIx3
Figure17:RackMountBracketfor2-100&DSP2-150MKII
IMPORTANT: ANY TIME THE PROTECTION CIRCUITS ARE TRIGGERED,
UNPLUG THE AMPLIFIER’S POWER CORD FROM THE WALL OUTLET
BEFORE TROUBLESHOOTING.
Amplier Power Supply Protection DSP 2-150 MKII
Theamplieralsohasprotectionforthepowersupply.Ifthepower
supply heat sink temperature exceeds the design maximum, the
protection circuit will activate, disconnecting all channel outputs.
This is indicated by a blinking light on the front panel power switch.
NOTE: IF SHELF MOUNTING, ATTACH THE FOUR INCLUDED FEET BY
SCREWING THEM INTO THE THREADED OPENINGS ON THE BOTTOM
CHASSIS. NO TOOL IS REQUIRED.
Front View
Front View
Loading ...
Loading ...
Loading ...