User Manual Pelonis PAT10H2ZWT 10,000 BTU 230-Volt Through-the-Wall Air Conditioner with Heat

Pelonis PAT10H2ZWT 10,000 BTU 230-Volt Through-the-Wall Air Conditioner with Heat - Use Manual - Use Guide PDF.
Documents: Go to donwload!
  • Owner's manual - (English)

User manual of Pelonis PAT10H2ZWT (36 pages)
file thumbnail

Before using your air conditioner. please read this manual carefully and keep it for future reference.

THROUGH THE WALL ROOM AIR CONDITIONE R

Before using your air conditioner. please read

WINDOW/WALL TYPE ROOM AIR C ONDITIONER

Before using your air conditioner. please read

WINDOW/WALL TYPE ROOM AIR C ONDITIONER

Before using your air conditioner. please read

WINDOW/WALL TYPE ROOM AIR C ONDITIONER

Before using your air conditioner. please read

WINDOW/WALL TYPE ROOM AIR C ONDITIONER

Before using your air conditioner. please read

WINDOW/WALL TYPE ROOM AIR C ONDITIONER

Before using your air conditioner. please read

WINDOW/WALL TYPE ROOM AIR C ONDITIONER

Before using your air conditioner. please read

WINDOW/WALL TYPE ROOM AIR C ONDITIONER

Before using your air conditioner. please read

WINDOW/WALL TYPE ROOM AIR C ONDITIONER

Before using your air conditioner. please read

WINDOW/WALL TYPE ROOM AIR C ONDITIONER

Before using your air conditioner. please read

WINDOW/WALL TYPE ROOM AIR C ONDITIONER

Before using your air conditioner. please read

WINDOW/WALL TYPE ROOM AIR C ONDITIONER

Before using your air conditioner. please read

WINDOW/WALL TYPE ROOM AIR C ONDITIONER

TABLE OF CONTENTS

Installation Instructions Normal Sounds 18 Important Safety Instructions .. 1 Troubleshooting Tips

Air Conditioner Features 18

Care and Cleaning .

MULTI-STEP SPEED ELECTRONIC CONTROL

PAT10R1ZWT PAT10H2ZWT PAT12R1ZWT

PAT12H2ZWT PAT14R2ZWT PAT14H2ZWT

Features of remote control

Remote control operation instruction .. 25

IMPORTANT SAFETY INSTRUCTIONS

Inside you will find many helpful hints on how to use and maintain your air conditioner properly. Just a little preventive care on your part can save you a great deal of time and money over the life of your air conditioner. You'll find many answers to common problems in the chart of troubleshooting tips. If you review our chart of Troubleshooting Tips first. you may not need to call for service at all.

To prevent injury to the user or other people and property damage. the following instructions must be followed. Incorrect operation due to ignoring of instructions may cause harm or damage. The seriousness is classified by the following indications.

This symbol indicates the possibility of death or serious injury.

Always do this.

Never do this.

CAUTION This symbol indicates the possibility of injury or damage to property.

WARNING

WARNING

Plug in power plug properly.

Do not modify power cord length or share the outlet with other appliances.

Always ensure effective grounding.

Unplug the unit if strange sounds. smell. or smoke comes from it.

Keep firearms away.

Ventilate room before operating air conditioner if there is a gas leakage from another appliance.

Otherwise. it may cause electric shock or fire due to excess heat generation.

It may cause electric shock or fire due to heat generation.

Incorrect grounding may cause electric shock.

It may cause fire and electric shock.

It may cause fire.

It may cause explosion. fire and. burns.

It may cause electric shock or fire due to heat generation.

It may cause electric shock.

It may cause failure of machine or electric shock.

It may cause fire and electric shock.

It may cause fire and electric shock.

It may cause electric shock or fire.

If the power cord is damaged. it must be replaced by the manufacturer or an authorised service centre or a similarly qualified per son in order to avoid a hazard.

This could damage your health.

Incorrect installation may cause fire and electric shock.

It may cause electric shock.

It may cause an explosion or fire.

It may cause failure and electric shock.

Do not operate or stop the unit by inserting or pulling out the power plug.

Do not operate with wet hands or in damp environment.

Do not allow water to run into electric parts.

Do not use the socket if it is loose or damaged.

Do not use the power cord close to heating appliances.

Do not damage or use an unspecified power cord.

Do not direct airflow at room occupants only.

Always install circuit breaker and a dedicated power circuit.

Do not open the unit during operation.

Do not use the power cord near flammable gas or combustibles. such as gasoline. benzene. thinner. etc.

Do not disassemble or modify unit.

READ THIS MANUAL

When the air filter is to be removed. do not touch the metal parts of the unit.

It may cause an injury.

Do not clean unit when power is on as it may c ause fi re an d el ectric sh ock. it may cause an injury.

Operation with windows opened may cause wetting of indoor and soaking of household furniture.

When the unit is to be cleaned. switch off. and turn off the circuit breaker.

Use caution when unpacking and installing. Sharp edges could cause injury.

Do not clean the air conditioner with water.

Water may enter the unit and degrade the insulation. It may cause an electric shock.

This could injure the pet or plant.

It may cause electric shock and damage.

Do not put a pet or house plant where it will be exposed to direct air flow.

Ventilate the room well when used together with a stove. etc.

An oxygen shortage may occur.

Do not use this air conditioner to preserve precision devices. food. pets. plants. and art objects.It may cause deterioration of quality. etc.

It may cause failure of product or fire.

Do not use for special purposes.

If water enters the unit. turn the unit off at the power outlet and switch off the circuit breaker. Isolate supply by taking the power-plug out and contact a qualified service technician.

It may cause failure of appliance or accident.

Appearance may be deteriorated due to change of product color or scratching of its surface.

If bracket is damaged. there is concern of damage due to falling of unit.

There is danger of fire or electric shock.

Operation without filters maycause failure.

It contains contaminants and could make you sick.

Stop operation and close the window in storm or hurricane.

Do not use strong detergent such as wax or thinner but use a soft cloth.

Ensure that the installation bracket of the outdoor appliance is not damaged due to prolonged exposure.

Hold the plug by the head of the power plug when taking it out.

Turn off the main power switch when not using the unit for a long time.

Always insert the filters securely.

Clean filter once every t wo w eeks.

Do not place heavy object on the power cord and ensure that the cord is not compressed.

Do not drink water drained from air conditioner.

This appliance is not intended for use by persons (including children) with reduced physical. ensory or mental capabilities or lack of experience and knowledge. unless t hey h aveb eengi vensu pervision or instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

If the supply cord is damaged. it must be replaced by the manufacturer. its service agent or similarly qualified persons in order to avoid a hazard.

CAUTION

CAUTION

Do not place obstacles around air-inlets or inside of air-outlet.

The appliance shall be installed in accordance with national wiring regulations.

Do not operate your air conditioner in a wet room such as a bathroom or laundry room.

The appliance with electric heater shall have at l east 1 m eter s pace to th eco mbustible materials.

Contact the authorised service technician for repair or maintenance of this unit.

Contact the authorised installer for installation of this unit.

IMPORTANT SAFETY INSTRUCTIONS

Do not. under any circumstances. cut. remove. or bypass the grounding prong.

Power supply cord with 3-prong grounding plug and current detection device

Grounding type wall receptacle

WARNING

NOTE:

The power supply cord with this air conditioner contains a current detection device designed to reduce the risk of fire.

Please refer to the section Operation of Current Device for details.In the event that the power supply cord is damaged. it cannot be repaired-it must be replaced with ac ordf romt heP roductM anufacturer.

Avoid fire hazard or electric shock. Do not use an extension cord or an adaptor plug.

Do not remove any prong from the power cord.

WARNING

For Your Safety

WARNING

Prevent Accidents

WARNING

Electrical Information

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

Operation of Current Device (Applicable to the unit adopts current detection device only ) The power supply cord contains a current device that senses damage to the power cord. To test your power supply cord do the following: 1. Plug in the Air Conditioner.

2. The power supply cord will have TWO buttons on the plug head. Press the TEST button. you will notice a click as the RESET button pops out.

3. Press the RESET button. again you will notice a click as the button engages.

4. The power supply cord is now supplying electricity to the unit. (On some products this it also indicated by a light on the plug head.)

To reduce the risk of fire. electrical shock. or injury to persons when using your air conditioner. follow basic precautions. including the following: Be sure the electrical service is adequate for the model you have chosen. This information can be found on the serial plate. which is located on the side of the the cabinet and behind the grille.

If the air conditioneri s t o b e in stalled in a w indow. yo u w ill pr obably w ant to cl ean both sides of the g lass f irst.I f th e w indowis a tri ple-track ty pe w ith a sc reen pa nel included. remove the screen completely before installation.

Be sure the air c onditionerh as b een s ecurely a nd c orrectly in stalled a ccording to the installation instructions in this manual. Save this manual for possible future use in removing or installing this unit.

When handling the air conditioner. be careful to avoid cuts f rom s harp m etal f ins on front and rear coils.

The complete electical rating of your new room air conditioner is stated on the serial plate. Refer to the rating when checking the electrical requirements.

Be sure the air conditioner is properly grounded. To minimize shock and fire hazards. proper grounding is important. The power cord is equipped with a three-prong grounding plug for protection against shock hazards.

Your air conditioner must be used in a properly grounded wall receptacle. If the wall receptacle you intend to use is not adequately grounded or protected by a time delay fuse or circuit breaker. have a qualified electrician install the proper receptacle. Ensure the receptacle is accessible after the unit installation.

Do not run air conditioner without side protective cover in place.This could result in mechanical damage within the air conditioner.

Do not use an extension cord or an adapter plug.

IMPORTANT SAFETY INSTRUCTIONS

Do not use this device to turn the unit on or off.

Always make sure the RESET button is pushed in for correct operation.

The power supply must be replaced if it fails reset when either the TEST button is pushed. or it cannot be reset. A new one can be obtained from the product manufacturer.

If power supply cord is damaged. it cannot be repaired. It MUST be replaced by one obtained from the product manufacturer.

NOTE:

NOTE:This air conditioner is designed to be operated under condition as follows:

Cooling operation

Outdoor temp:

Indoor temp:

Heating operation

Outdoor temp: 23-76 F/-5-24 C

Indoor temp:

32-80 F/0-27 C

64-109 F/18-43 C (64-125 F/18-52 C for special tropical models)

62-90 F/17-32 C

Note: Performance may be reduced outside of these operating temperatures.

INSTALLATION INSTRUCTIONS

Read these instructions completely and carefully.

IMPORTANT- Save these instructions for local inspector s use.

IMPORTANT- Observe all governing codes and ordianaces.

Note to Consumer- Keep these instructions for futrue reference.

Note to Installer- Be sure to leave these instructions with the Consumer.

Completion time- Approximately 1 hour.

Skill level- Installatio of this appliance requires basic mechanical skills.

We recommend that two people install this product.

Proper installation is the responsibility of the installer.

Product failure due to improper installation is not covered under the Warranty.

You MUST use all supplied parts and use proper installation procedures as described in these instructions when installing this air conditioner.

BEFORE YOU BEGIN

Do not. under any circumstances. cut or remove the third (ground) prong from the power cord.

CAUTION

Do not change the plug on the power cord of the air conditioner.

Aluminum house wiring may present special problems- consult a qualified electircian.

When handling unit. be careful to avoid cuts from sharp metal edges and aluminum fins on front and rear coils.

Save Carton and these Installation Instructions for future reference. The carton is the best way to store unit during winter. or when not in use.

NOTE:

Note that the air conditioner dimensions are: 24 inches wide. 14 inches high. and 18 inches deep(without front).

Install Air Conditioner according to these installation instructions to achieve the best performance. Save these installation instructions for future reference.

NOTE: Do not use any screws other than those specified here.

Do This First (for existing sleeve)

Items in Kit

You may not need all parts in the kit. Discard unused parts.

Name

Spec.

Qty

Tapered Spacer Blocks

17 Long Centering/Support Blocks 4 x3 x1 Plastic Divider 1/8 x4 x14 Stuffer Seal 1 x1 x84 1 Seal 1 x1 x25

1 x1 x14 1 x3/8 x25

Seal 1 x3/8 x14 1 x3/4 x14 Seal

Trim Frame(side legs) Trim Frame(top & bottom legs) Ground Wire(green) Toothed Washer for grounding screw

Grounding Screw Grille(plastic) Grille Aluminum Nuts(plastic) Screw Washer Screw

How to Install

1. Identify the wall-sleeve brand for your installation. from the chart below.

Wall Sleeve Dimensions (inches) Width Height Depth

Brand

Pelonis White-Westinghouse Frigidaire Carrier(52F Series) General Electric/Hotpoint Whirlpool Fedders/Emerson Sears/Kenmore Carrier(51S Series) Emerson/Fedders Friedrich

16.17 or 22

17 or 23

16 or 19

NOTE: All wall sleeves used to mount the new Air Conditioner must be in sound structural condition and have a rear grille that securely attaches to sleeve. or rear flange that serves as a stop for the Air Conditioner.

CAUTION: When installation is complete. replacement unit MUST have a rearward slope as shown.

REAR

LEVEL

FRONT

UNIT

Wall Sleeve

1/4 to 5/16

2. Remove old Air Conditioner from wall sleeve and prepare wall sleeve as follows: Clean interior (do not disturb seals).

Wall sleeve must be securely fastened in wall before installing Air Conditioner.

Drive more nails or screws through sleeve. into wall. if needed.

Repair paint if needed.

3. If not existing. drill a 1/8 clearance hole for grounding screw through left side of wall sleeve. in a clear area about 3 inches maximum back from front edge of sleeve. using grounding screw and toothed washer. Pull loose end of ground wire out front of sleeve. and temporarily bend it down and around lower edge of sleeve.This ground wire will later be attached to frame of air conditioner once it is installed.

Wall sleeve to unit sleeve grounding

Max.

Hole

4. Prepare the wall sleeve for installation of the new unit per the following Brand instructions. #1 Emerson 15 Deep #2 Fedders 19 Deep #3 Fedders or Friedrich 16 Deep #4 General Electric/Hotpoint 16 Deep #5 Sears or Carrier(51S Series) 18 Deep #6 Whirlpool 17 Deep #7 Whirlpool 23 Deep

Frigidaire/Carrier(52F Series) #9 White-Westinghouse/Frigidaire 22 Deep

3/4/4

7/8/

3/4/4

5/8/

1/8/

#8 Pelonis/White-Westinghouse/

5. Identify your wall sleeve type and follow the instructions for that type in the following pages.

INSTALLATION INSTRUCTIONS

This units increased performance characteristics result from having two rear air intakes.

It is very important that these installation instructions are followed so your unit can operate at maximum efficiency.

If this is an existing sleeve. and there is an existing rear grille. it needs to be replaced by one that has been shipped with the unit in the accessory kit.

FOR INCREASED EFFICIENCY. TILIZE THE PROVIDED LOUVERED REAR PANEL Installation of new grille provided with unit 1. Remove the existing grille.

2. Place the grille included with the new air conditioner towards the rear of the sleeve.

3. Mark through the hole positions.

4. Drill through the sleeves flanges with a 1/8 drill bit.

5. Attached the new grille with self-threading screws and washers.

6. It is VERY IMPORTANT that the grille is placed exactly as shown below.

7. Most decorative exterior grilles may be left in place as long as the proper interior air direction grille is installed.

INSTALLATION INSTRUCTIONS

IMPORTANT

INSTALLATION INSTRUCTIONS

Wall Sleeve Brands:

#1 Emerson 15 Deep

1. Remove existing rear grille as shown on Page 6 of this manual and replace with provided louvered rear panel. Install as shown here.

NOTE: You may need to drill holes in flange of existing sleeve to match new rear grille.

2. Attach(1)1 x3/8 x25 long seal in the center at the top of the sleeve. Remove the backing paper and press into position.

3. Attach the (2) 1 x3/8 x14 long seals to the left and right sides of the sleeve.

4. Cut (2) 1 x3/8 x25 long seals to 14 long. nd attach it to the vertical sections of the rear grille as shown.

5. Attach (2)4 x3 x1 centering/support blocks one on each side wall. Place in center of side wall with the tapered end facing the opening.

6. Gently slide unit into sleeve.

7. Before sliding all-the-way back. remove 2nd screw from front on left side of unit.

8. Remove the plastic washer from the screw.

9. Screw and attach the other end of the ground wire to the unit as shown in picture. Make sure that the toothed washer is against the cabinet.

10.Slide the unit completely to the rear to ensure a good seal. making sure the ground wire does not become tangled.

11.Seal & Frame the unit as described on page 17.

12. If you have difficulty with mounting the grill to the sleeve. follow the instructions for direct mounting on Page 16.

INSTALLATION INSTRUCTIONS

Wall Sleeve Brands:

#2 Fedders 19 Deep

2. Attach(2)4 x3 x1 centering/support blocks one on each side wall. Place in center of side wall with the tapered end facing the opening.

3. Cut (2) 17 Tapered Spacer Blocks as shown below into two pieces.

4. The 4 section is placed in front of the rib on base with the tapered end facing the back of the sleeve. The remaining portion will be placed behind the rib again sloping toward the rear of the sleeve. This helps induce a rearward slope on the unit.

5. Attach (1)1 x3/8 x25 long seal in the center at the top of the sleeve. Remove the backing paper and press into position.

6. Attach (2) 1 x3/8 x14 seals to the left and right sides of the sleeve.

7. Cut (2) 1 x3/8 x25 long seals to 14 long and attach it to the vertical sections of the rear grille as shown.

8. Gently slide unit into sleeve.

9. Before sliding all-the-way back. remove 2nd screw from front on left side of unit.

10. Remove the plastic washer from the screw.

11. Screw and attach the other end of the ground wire to the unit as shown in picture. Make sure that the toothed washer is against the cabinet.

12.Slide the unit completely to the rear to ensure a good seal. making sure the ground wire does not become tangled.

13.Seal & Frame the unit as described on page 17.

14. If you have difficulty with mounting the grill to the sleeve. follow the instructions for direct mounting on Page 16.

1/2/2

Cut Here

Tapered Spacer Block

Protection Paper Backing

Remove existing rear grille as shown on Page 6 of this manual and replace with provided louvered rear panel. Install as shown here.

NOTE: You may need to drill holes in flange of existing sleeve to match new rear grille.

INSTALLATION INSTRUCTIONS

Wall Sleeve Brands:

#3 Fedders or Friedrich 16 Deep

1.Remove existing rear grille as shown on Page 6 of this manual and replace with provided louvered rear panel. Install as shown here.

NOTE: You may need to drill holes in flange of existing sleeve to match new rear grille.

2. Attach(2)4 x3 x1 centering/support blocks one on each side wall. Place in center of side wall with the tapered end facing the opening.

3. Cut (2) 17 Tapered Spacer Blocks as shown below into three pieces.

4. The 2 section is placed in front of the rib on base with the tapered end facing the back of the sleeve. Cut the remaining portion to 12 and placed behind the rib again sloping toward the rear of the sleeve. This helps induce a rearward slope on the unit.

5. Attach (1)1 x3/8 x25 long seal in the center at the top of the sleeve. Remove the backing paper and press into position.

6. Attach (2) 1 x3/8 x14 seals to the left and right sides of the sleeve.

7. Cut (2) 1 x3/8 x25 long seals to 14 long and attach it to the vertical sections of the rear grille as shown.

8. Gently slide unit into sleeve.

9. Before sliding all-the-way back. remove 2nd screw from front on left side of unit.

10. Remove the plastic washer from the screw.

11. Screw and attach the other end of the ground wire to the unit as shown in picture. Make sure that the toothed washer is against the cabinet.

12.Slide the unit completely to the rear to ensure a good seal. making sure the ground wire does not become tangled.

13.Seal & Frame the unit as described on page 17.

14. If you have difficulty with mounting the grill to the sleeve. follow the instructions for direct mounting on Page 16.

1/2/2

Cut Here

Tapered Spacer Block

Protection Paper Backing

12-1/2 2-1/2

INSTALLATION INSTRUCTIONS

Wall Sleeve Brands:

1. Remove existing rear grille as shown on Page 6 of this manual and replace with provided louvered rear panel. Install as shown here.

NOTE: You may need to drill holes in flange of existing sleeve to match new rear grille.

#4 General Electric/Hotpoint 167/8 Deep

2. Cut (2) 17 Tapered Spacer Blocks as shown below into two pieces.

3. Install 13 section as shown with the tapered end from the back of the sleeve. This helps induce a rearward slop on the unit.

4. Attach (1)1 x3/8 x25 long seal in the center at the top of the sleeve. Remove the backing paper and press into position.

5. Attach (2) 1 x3/8 x14 seals to the left and right sides of the sleeve.

6. Cut (2) 1 x3/8 x25 long seals to 14 long and attach it to the vertical sections of the rear grille as shown.

7. Center unit and gently slide unit into sleeve.

8. Before sliding all-the-way back. remove 2nd screw from front on left side of unit.

9. Remove the plastic washer from the screw.

10. Screw and attach the other end of the ground wire to the unit as shown in picture. Make sure that the toothed washer is against the cabinet.

11.Slide the unit completely to the rear to ensure a good seal. making sure the ground wire does not become tangled.

12.Seal & Frame the unit as described on page 17.

13. If you have difficulty with mounting the grill to the sleeve. follow the instructions for direct mounting on Page 16.

Tapered Spacer Block

Protection Paper Backing

Cut Here

INSTALLATION INSTRUCTIONS

Wall Sleeve Brands:

#5 Sears or Carrier 51S Series ( 18 Deep)

1. Remove existing rear grille as shown on Page 6 of this manual and replace with provided louvered rear panel. Install as shown here.

NOTE: You may need to drill holes in flange of existing sleeve to match new rear grille.

2. Install (2) tapered spacer blocks to the floor of the sleeve as shown. This helps induce a rearward slop on the unit.

3. Install as shown with the tapered end from the back of the sleeve. This helps induce a rearward slop on the unit.

4. Attach (1)1 x3/8 x25 long seal in the center at the top of the sleeve. Remove the backing paper and press into position.

5. Attach (2) 1 x3/8 x14 seals to the left and right sides of the sleeve.

6. Cut (2) 1 x3/8 x25 long seals to 14 long and attach it to the vertical sections of the rear grille as shown.

7. Center unit and gently slide unit into sleeve.

8. Before sliding all-the-way back. remove 2nd screw from front on left side of unit.

9. Remove the plastic washer from the screw.

10. Screw and attach the other end of the ground wire to the unit as shown in picture. Make sure that the toothed washer is against the cabinet.

11.Slide the unit completely to the rear to ensure a good seal. making sure the ground wire does not become tangled.

12.Seal & Frame the unit as described on page 17.

13. If you have difficulty with mounting the grill to the sleeve. follow the instructions for direct mounting on Page 16.

INSTALLATION INSTRUCTIONS

Wall Sleeve Brands:

#6 Whirlpool 17 Deep

1. Remove existing rear grille as shown on Page 6 of this manual and replace with provided louvered rear panel. Install as shown here.

NOTE: You may need to drill holes in flange of existing sleeve to match new rear grille.

2. Cut (2) 17 Tapered Spacer Blocks as shown below into two pieces.

3. Install 13 section to the floor of the sleeve as shown. This helps induce a rearward slop on the unit.

4. Attach (1)1 x3/8 x25 long seal in the center at the top of the sleeve. Remove the backing paper and press into position.

5. Attach (2) 1 x3/8 x14 seals to the left and right sides of the sleeve.

6. Cut (2) 1 x3/8 x25 long seals to 14 long and attach it to the vertical sections of the rear grille as shown.

7. Center unit and gently slide unit into sleeve.

Tapered Spacer Block

Protection Paper Backing

Cut Here

8. Before sliding all-the-way back. remove 2nd screw from front on left side of unit.

9. Remove the plastic washer from the screw.

10. Screw and attach the other end of the ground wire to the unit as shown in picture. Make sure that the toothed washer is against the cabinet.

10. Slide the unit completely to the rear to ensure a good seal. making sure the ground wire does not become tangled.

12. Seal & Frame the unit as described on page

13. If you have difficulty with mounting the grill to the sleeve. follow the instructions for direct mounting on Page 16.

INSTALLATION INSTRUCTIONS

Wall Sleeve Brands: #7 Whirlpool ( 23 Deep)

1. Remove existing rear grille as shown on Page 6 of this manual and replace with provided louvered rear panel. Install as shown here.

NOTE: You may need to drill holes in flange of existing sleeve to match new rear grille.

2. Place (2) 1 x1 x14 seals against each side.

3. Gently slide unit in and check if amount extend ing from the sleeve is sufficient once the trim frame is attached.

4. If position is Ok. remove unit and proceed to the next step. If not go to step 9.

5. Attach (1)1 x1 x25 long seal in the center at the top of the sleeve. Remove the backing paper and press into position.

6. Attach (2) 1 x1 x14 seals to the left and right sides of the sleeve.

7. Cut (2) 1 x x25 long seals to 14 long and attach to the vertical sections of the grille as shown.

8. Attach the tapered spacer blocks to the floor of the sleeve. Now go to step 15.

Use these next steps if the unit requires extra extension into the room.

9. Attach 1 x x14 long seal over the solid vertical portion of the rear grille.

10. Attach (4) 4 x3 x1 foam blocks with the slot overlapping the seal above.

11. Install the divider into the slots of the foam blocks. You may need to trim the length to size.

12. Repeat steps 9-11 for the other vertical shown portion of the grille as shown in the picture.

13. Attach (2) 1 x1 x14 seals along the sides of the sleeve again making sure all seals are flush.

14.Cut the 1 x1 x25 seal to fit the top of the sleeve. The pieces must be fitted flush to the edge of the divider.

15. Center unit and gently slide unit into sleeve.

16. Before sliding all-the-way back. remove 1st screw from front on left side of unit.

17. Remove the plastic washer from the screw.

18. Screw and attach the other end of the ground wire to the unit as shown in picture. Make sure that the toothed washer is against the cabinet.

19.Slide the unit completely to the rear to ensure a good seal. making sure the ground wire does not become tangled.

20.Seal & Frame the unit as described on page 17.

21. If you have difficulty with mounting the grill to the sleeve. follow the instructions for direct mounting on Page 16.

Because of the increased unit depth. first try dry fitting using the method described below:

1 /2

INSTALLATION INSTRUCTIONS

Wall Sleeve Brands:

#8 Pelonis/White Westinghouse/Frigidaire

Carrier 52F Series ( 16 +17 Deep)

1.Remove existing rear grille as shown on Page 6 of this manual and replace with provided louvered rear panel. Install as shown here.

NOTE: You may need to drill holes in flange of existing sleeve to match new rear grille.

2. Attach (1)1 x3/8 x25 long seal in the center at the top of the sleeve. Remove the backing paper and press into position.

3. Attach (2) 1 x3/8 x14 seals to the left and right sides of the sleeve.

4. Attach (2) 1 x3/4 x14 long seals vertically 4.5 from the left side of the sleeve .Attach the other 1 x3/4 x14 long seal 4 from the right side of the sleeve.

5. Center unit and gently slide unit into sleeve.

6. Before sliding all-the-way back. remove 2nd screw from front on left side of unit.

7. Remove the plastic washer from the screw.

8. Screw and attach the other end of the ground wire to the unit as shown in picture. Make sure that the toothed washer is against the cabinet.

9. Slide the unit completely to the rear to ensure a good seal. making sure the ground wire does not become tangled.

10.Seal & Frame the unit as described on page 17.

11. If you have difficulty with mounting the grill to the sleeve. follow the instructions for direct mounting on Page 16.

INSTALLATION INSTRUCTIONS

Wall Sleeve Brands:

#9 White Westinghouse or Frigidaire ( 22 Deep)

2. Place (2) 1 x1 x14 seals against each side.

3. Gently slide unit in and check if amount extend ing from the sleeve is sufficient once the trim frame is attached.

4. If position is Ok. remove unit and proceed to the next step. If not go to step 8.

5. Attach (1)1 x1 x15 long seal to the left and right sides of the sleeve.

6. Cut (1) 1 x1 x25 long seal to 14 long and attach it vertically to the rear grill 4.5 from the left side. epeat and attach 4 from the right side.

7. Attach(1) 1 x1 x25 long seal in the center at the top of the sleeve.Remove the backing paper and press into position.Proceed to step 14.

Use these next steps if the unit requires extra extension into the room.

8. Attach 1 x x14 long seal over the solid vertical portion of the rear grille.

9. Attach (4) 4 x3 x1 foam blocks with the slot overlapping the seal above.

10. Install the divider into the slots of the foam blocks. You may need to trim the length to size.

11. Repeat steps 8-10 for the other vertical shown portion of the grille as shown in the picture.

12. Attach (2) 1 x1 x14 seals along the sides of the sleeve again making sure all seals are flush.

13.Cut the 1 x1 x25 seal to fit the top of the sleeve. The pieces must be fitted flush to the edge of the divider.

14. Center unit and gently slide unit into sleeve.

15. Before sliding all-the-way back. remove 1st screw from front on left side of unit.

16. Remove the plastic washer from the screw.

17. Screw and attach the other end of the ground wire to the unit as shown in picture. Make sure that the toothed washer is against the cabinet.

18.Slide the unit completely to the rear to ensure a good seal. making sure the ground wire does not become tangled.

19.Seal & Frame the unit as described on page 17.

20. If you have difficulty with mounting the grill to the sleeve. follow the instructions for direct mounting on Page 16.

Because of the increased unit depth. first try dry fitting using the method described below:

Remove existing rear grille as shown on Page 6 of this manual and replace with provided louvered rear panel. Install as shown here.

NOTE: You may need to drill holes in flange of existing sleeve to match new rear grille.

INSTALLATION INSTRUCTIONS

Direct Unit Mounting:

The previous directions are the preferable way to mount the new rear grill. The units performance is slightly better and the possibility of draughts is reduced. As a last resort. direct mounting of the grille to the unit can be considered.

Note: The grille must be installed prior to inserting the unit into the sleeve.

1. Attach the 2 seal pieces (1 X3/8 X14 ) as shown in Fig. 1.

2.Position the grille over the rear of the unit making sure that: a. The double set of screw holes are at the bottom. b. The fins of the grill are pointed away from the unit.

3. Align the top of the grille with the top of the unit. The overhang on each side is equal.

4. If the unit has not been pre-drilled (some models). carefully drill 4-1/8 holes through the grille and into the side flange of the unit approximately 1 to 2 from the top and bottom as in Fig. 2. 3 . (Be careful not to drill into the copper heat exchanger coils.) 5. Install 4 - #8 self tapping screws to affix the grille to the unit.

6. Insert the unit into the sleeve.

1. Install the 1 x1 x84 long stuffer-seal between the wall-sleeve and the unit. A flat-bladed screwdriver or putty knife is recommended.

2. Assemble the trim frame by inserting top and bottom pieces into side pieces and snapping into place.

3. Pull cord through trim frame then slide over unit until flush with wall.

INSTALLATION INSTRUCTIONS

FINISHING INSTALLATION:

NORMAL SOUNDS

All the illustrations in this manual are for explanation purpose only. Your air conditioner may be slightly different.

NOTE:

AIR CONDITIONER FEATURES

Before you begin. thoroughly familiarize yourself with the control panel as shown below and all its functions. then follow the symbol for the functions you desire. The unit can be controlled by the unit control alone or with the remote.

ELECTRONIC CONTROL OPERATING INSTRUCTIONS

Sound of Rushing Air

At the front of the unit. you may hear the sound of rushing air being moved by the fan

High Pitched Chatter

High efficiency compressors may have a high pitched chatter during the cooling cycle.

Gurgle/Hiss

Gurgling or hissing noise may be heard due to refrigerant passing through evaporator during normal operation.

Pinging or Switching

Droplets of water hitting condenser during normal operation may cause pinging or switching sounds.

Vibration

Unit may vibrate and make noise because of poor wall or window construction or incorrect installation.

(Cooling Only Models)

(Electric Heating Models)

RECEPTOR TO TURN UNIT ON OR OFF:

Press ON/OFF button to t urn unit on or off.

NOTE: The Energy Saver function will automatically initiate under the Cool. Dry. Auto (only Auto-Cooling and Auto-Fan) modes.”

TO CHANGE TEMPERATURE SETTING:

Press / UP/DOWN button to change temperature setting.

NOTE:Press or hold either UP( ) or DOWN ( ) button until the desired temperature is seen on the display.

This temperature will be automatically maintained anywhere between 62 F(17 OC) and 86 F(30 OC). If you want the display to read the actual room temperature. see To Operate on Fan Only section.

AIR CONDITIONER FEATURES

TO ADJUST FAN SPEEDS:

Press to select the Fan Speed in four steps-Auto.

Low. Med or High. Each time the button is pressed. the fan speed mode is shifted.For some models. the fan speed can not be adjusted under HEAT mode.

On Dry mode. he fan speed is controlled at Low automatically.

TO SELECT THE OPERATING MODE:

To choose operating mode. press Mode button.Each time you press the button. a mode is selected in a sequence that goes from Auto. Cool. Dry. eat(cooling only models without)and Fan. The indicator light beside will be illuminated and remained on once the mode is selected.

The unit will initiate automatically the Energy Saver function under Cool. Dry. Auto(only Auto-Cooling and Auto-Fan) modes.

To operate on Auto feature: When you set the air conditioner in AUTO mode. it will automatically select cooling. heating(cooling only models without). or fan only operation depending on what temperature you have selected and the room temperature.

The air conditioner will control room temperature automatically round the temperature point set by you.

In this mode. the fan speed cannot be adjusted. it starts automatically at a speed according to the room temperature.

To operate on Fan Only: Use this function only when cooling is not desired. uch as for room air circulation or to exhaust stale air(on some models). (Remember to open the vent during this function. but keep it closed during cooling for maximum cooling efficiency.) You can choose any fan speed you prefer.

During this function. the display will show the actual room temperature. not the set temperature as in the cooling mode.

In Fan only mode. he temperature is not adjusted.

To operate on Dry mode: In this mode. the air conditioner will generally operate in the form of a dehumidifier. Since the conditioned space is a closed or sealed area. some degree of cooling will continue.

SLEEP FEATURE:

Press Sleep button to initiate the sleep mode. In this mode the selected temperature will increase (cooling) or decrease (heating) by 2 F/1(or 2) OC 30 minutes after the mode is selected.T he t emperature will then increase (cooling) or decrease (heating) by another 2 F/1(or 2) OC after an additional 30 minutes.

T his n ew t emperature w ill be m aintained f or 6 h ours beforei t r eturnsto th e originally se lected tem perature.

This ends the Sleep mode and the unit will continue t o operate as originally programmed. The Sleep mode program can be cancelled at any time during operation by pressing the Sleep button again.

Press Check filter button to initiate this feature.

This feature is a reminder to clean the Air Filter for more efficient operation. The LED(light) will illuminate after 250 hours of operation. To reset after cleaning the filter. press the Check Filter button and the light will go off.

CHECK FILTER FEATURE:

ENERGY SAVER FEATURE:

Press Energy saver button to initiate this function.

This function is available on COOL. DRY. AUTO (only AUTO-COOLING and AUTO-FAN) modes.The fan will continue to run for 3 minutes after the compressor shuts off.The fan then cycles on for 2 minutes at 10 minute intervals until the room temperature is above the set temperature. at which time the compressor turns back on and Cooling Starts.

FOLLOW ME FEATURE:(on some models)

Light flashing

Follow Me

This feature can be activated from the remote control ONLY. The remote control serves as a remote thermostat allowing for the precise temperature control at its location.

To activate the Follow Me feature. point the remote control towards the unit and press the Follow Me button. The remote display is actual temperature at its location. The remote control will send this signal to the air conditioner every 3 minutes interval until press the Follow Me button again.If the unit does not receive the Follow Me signal during any 7 minutes interval. the unit will beep to indicate the Follow Me mode has ended.

When the unit is on or off. first press Timer button. the TIMER ON indicator light illuminates. It indicates the Auto Start program is initiated.

When the time of TIMER ON is displayed. ress the Timer button again. the TIMER OFF indicator light illuminates.

It indicates the Auto Stop program is initiated.

Press or hold the UP or DOWN button to change the Auto time by 0.5 hour increments. up to 10 hours. hen at 1 hour increments up to 24 hours.The control will count down the time remaining until start.

The selected time will register in 5 seconds. and the system will automatically revert back to display the previous temperature setting or room temperature when the unit is on.(when the unit is off. here is no display.) Turning the unit ON or OFF at any time or adjusting the timer setting to 0.0 will cancel the Auto Start/Stop timed program.

TIMER: AUTO START/STOP FEATURE:

AIR CONDITIONER FEATURES

Displays

Shows the set temperature in C or F and the Auto-timer settings.While on Fan only mode. t shows the room temperature.

DISPLAYS:

Evaporator temperature sensor error-Unplug the unit and plug it back in.If error repeats. call for service.

NOTE: is displayed as shown in the left picture.

HS -Electric heating sensor error-Unplug the unit and plug it back in.If error repeats. call for service.

Error codes: AS-Room temperature sensor error-Unplug the unit and plug it back in.If error repeats. call for service.

NOTE:In Fan only mode. t will display LO or HI .

If the power cuts off unexpectedly. the unit will automatically restart to the previous function setting when the power resumes

DISPLAYS:

NOTE:

Now that you have mastered the operating procedure. here are more features in your control that you should become familiar with.

The Cool circuit has an automatic 3 minute time delayed start if the unit is turned off and on quickly.

This prevents overheating of the compressor and possible circuit breaker tripping.The fan will continue to run during this time.

The control is capable of displaying temperature in degrees Fahrenheit or degrees Celsius. To convert from one to the other. press and hold the Left and Right Temp/Timer buttons at the same time. for 3 seconds.

CAUTION

Clean your air conditioner occasionally to keep it looking new. Be sure to unplug the unit before cleaning to prevent chock or fire hazards.

Air Filter Cleaning

The air filter should be checked at least once a month to see if cleaning is necessary. Trapped particles in the filter can build up and cause an accumulation of frost on the cooling coils.

Air Direction(4- way) Air directional louvers control air flow direction.Your air conditioner has the 4-way directional system described below.The louvers will allow you to direct the air flow Up or Horizontal. and Left or Right throughout the room as needed.Use the center handles to adjust the air directional louvers side-to-side until the desired Left or Right direction is obtained.Pivot horizontal louvers with your fingertips until the desired Up or Horizontal direction is obtained.There are a total of 4 possible air directional orientations available with this system.

ADDITIONAL THINGS YOU SHOULD KNOW

Air Directional Louvers

CARE AND CLEANING

Center handles Louvers

CARE AND CLEANING

Air Filter Cleaning

Take the filter by the center and pull up and out.

Wash the filter using liquid dishwashing detergent and warm water. Rinse filter thoroughly. Gently shake excess water from the filter. Be sure the filter is thoroughly dry before replacing. Or. instead of washing you may vacuum the filter clean.

Note: Never use hot water over 40 C(104 F) to cl ean th e a i r fil ter. Never attempt to operate the unit without the air filter.

Winter Storage

If you plan to store the air conditioner during the winter. remove it carefully from the window according to the installation instructions. Cover it with plastic or return it to the original carton.

Cabinet Cleaning

Be sure to unplug the air conditioner to prevent shock or fire hazard. The cabinet and front may be dusted with an oil-free cloth or washed with a cloth dampened in a solution of warm water and mild liquid dishwashing detergent. Rinse thoroughly and wipe dry.

Never use harsh cleaners. wax or polish on the cabinet front.

Be sure to wring excess water from the cloth before wiping around the controls. Excess water in or around the controls may cause damage to the air conditioner.

Plug in air conditioner.

TROUBLESHOOTING TIPS

Before calling for service. review this list. It may save your time and expense. This list includes common occurrences that are not the result of defective workman-ship or materials in this appliance.

Solution

Air conditioner does not start

Wall plug disconnected. Push plug firmly into wall outlet.

House fuse blown or circuit breaker tripped. Replace fuse with time delay type or reset circuit breaker.

Plug Current Device Tripped. Press the RESET button.

Problem

Air from unit does not feel cold enough

Set to a Lower temperature.

Room temperature below 62 F(17 C ). Cooling may not occur until room temperature rises above 62 F(17 C).

Thermostat set too cold for night-time cooling. To defrost the coil. set to FAN ONLY mode. Then. set temperature to a Higher setting.

Temperature sensing behind air filter element touching cold coil. Keep it from the cold coil.

Air filter may be dirty. Clean filter. Refer to Care and Cleaning section. To defrost. set to FAN ONLY mode.

Power is OFF. Turn power ON.

Air conditioner cooling. but room is too warm- ice forming on cooling coil behind decorative front.

Outdoor temperature below 64 F(18 C). To defrost the coil. set FAN ONLY mode.

Compressor stopped when changing modes. Wait for 3 minutes after set to the COOL mode.

Energy Saving Note:

In order to reach the maximum energy saving and comfort. it is recommended to use a cover to insulate the unit when the unit is not in use. The recommended size for the unit is 24.4 x14.8 x2.2 (WxHxD).

TROUBLESHOOTING TIPS

Solution Problem

Dirty air filter- air restricted. Clean air filter. Refer to Care and Cleaning section.

Unit recently turned on in hot room. Allow additional time to remove Stored heat from walls. ceiling. floor and furniture.

Air conditioner cooling. but room is too warm- NO ice forming on cooling coil behind decorative front.

Temperature is set too High. set temperature to a Lower setting.

Air directional louvers positioned improperly. Position louvers for better air distribution.

Front of units is blocked by drapes. blinds. furniture. etc. - restricts air distribution.

Clear blockage in front of unit.

Doors. windows. registers. etc. Open- cold air escapes. Close doors. windows. registers.

Air conditioner turns on and off rapidly

Noise when unit is cooling

Water dripping INSIDE when unit is cooling.

Improper installation. Tilt air conditioner slightly to the outside to allow water drainage.

Refer to installation instructions - check with installer.

Dirty air filter- air restricted. Clean air filter.

Air movement sound. This is normal. If too loud. set to a slower FAN setting.

Outside temperature extremely hot. Set FAN speed to a Higher setting to bring air past cooling coils more frequently.

Window vibration - poor installation. Refer to installation instructions or check with installer.

Water dripping OUTSIDE when unit is cooling.

Remote Sensing Deactivating Prematurely (some models)

Remote control not located within range. Place remote control within 20 feet & 180 . radius of the front of the unit.

Remote control signal obstructed. Remove obstruction.

Room too cold Set temperature too low. Increase set temperature.

Unit removing large quantity of moisture from humid room. This is normal during excessively humid days.

Press this botton to turn unit on or off.

NOTE: The unit will initiate automatically the Energy Saver function under Cool. Dry. Auto (only Auto-Cooling and Auto Fan) modes.

This funtion is available on COOL.

DRY. AUTO (only AUTO-COOLING and AUTO-FAN) modes.

The fan will continue to run for 3 minutes after the compressor shuts off. The fan then cycles on for 2 minutes at 10 minutes intervals until the room temperature is above the set temperature. at which time the compressor turns back on and Cooling Starts.

FOLLOW ME

Air Conditioner Limited Warranty

Your product is protected by this Limited Warranty:

Warranty service must be obtained from Midea Consumer Services or an authorized Midea servicer.

Warranty

Two Year Limited Warranty from original purchase date. Five Year Limited Sealed System (Sealed system includes components containing refrigerant) Warranty from original purchase date.

Midea. through its authorized servicers will:

Pay all costs for reparing or replacing parts of this appliance which prove to be defective in materials or workmanship.

Consumer will be responsible for:

Diagnostics. removal. transportation and reinstallation cost required because of service.

Costs of service calls that are a result of items listed under NORMAL RESPONSABILITIES OF THE CONSUMER**

Midea replacement parts shall be used and will be warranted only for the original warranty.

NORMAL RESPONSABILITIES OF THE CONSUMER**

This warranty applies only to products in ordinary household use. and the consumer is responsible for the items listed below:

Proper use of the appliance in acordance with instructions provided with the product.

Routine maintenance and cleaning necessary to keep the good working condition.

Proper installation by an authorized service professional in accordance with instructions provided with the appliance and in accordance with all local plumbing. electrical and/or gas codes.

Proper connection to a grouded power supply of sufficient voltage. replacement of blown fuses. repair of loosen connections or defects in house wiring.

Expenses for making the appliance accessible for servicing.

Damages to finish after intallation.

EXCLUSIONS

This warranty does not cover the following:

Failure caused by damage to the unit while in your possesion (other than damage caused by defect or malfunction). by its improper installation. or by unreasonable use of the unit. including without limitation. failure to provide reasonable and necessary maintenance or to follow the written installation and Operating Instructions.

Damages caused by services performed by persons other than authorized Midea costumer service; or external causes such as abuse. misuse. inadequate power supply or acts of God.

If the unit is put to commercial. business. rental. or other use or application other than for consumer use. we make no warranties. express or implied. including but not limited to. any implied warranty of merchantability or fitness for use or purpose.

4) Products without original serial numbers or products that have serial numbers which have been altered or cannot be readily determined.

NOTE: Some states do not allow the exclusions or limitation of incidental or consequential damages. So this limitation or exclusion may not apply to you.

IF YOU NEED SERVICE

Keep your bill of sale. delivery slip. or some other appropriate payment Record.

The date on the bill establishes the warranty period. should service be required.

If service is performed. its your best interest to obtain and keep all receipts.

This written warranty gives you specific legal rights. You may also have other rights that vary from state to state.

Service under this warranty must be obtained by following these steps. in order:

Contact Midea Consumer Services or an authorized Midea services at 1 866 646 4332.

If there is a question as to where to obtain service. contact our consumer relations Departament.

Warranty

Warranty



Newest Added: PAWF01 PAT12H2ZWT PAT12R1ZWT PP09HMB82 PP15HMB82

Tags: Pelonis Air Conditioner, Who Makes Pelonis Dehumidifiers, Pelonis Dehumidifier Manual, Pelonis Air Cooler Manual, Pelonis Dehumidifier, Pelonis Heater Instructions, Pelonis Dehumidifier How To Use

Pelonis PAT10H2ZWT | Pages: 36 | Created on: 2017-05-20 | File type: PDF | Filename: 66130791_pat10h2zwt.pdf | Size: 6.84 MB | Language: English

Download User Manual

Product Infomation and Reviews - PAT10H2ZWT photo

PAT10H2ZWT Photo

T: @manualsFile

https://manualsFile.com