Loading ...
Loading ...
Loading ...
5
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools
listed here.
Tools needed:
■ Level
■ Drill with 1¼" (3.0 cm), ½" (12.7 mm) and ³⁄₁₆" (5.0 mm)
drill bits
■ Pencil
■ Tape measure or ruler
■ Pliers
■ Caulking gun and weatherproof caulking compound
■ Vent clamps
■ Jigsaw or keyhole saw
■ Flat-blade screwdriver
■ Metal snips
■ Phillips screwdriver
■ ½" (13 mm) socket and driver with 24" (61 cm) of extensions
■ T20
®†
TORX
®
bit or driver
Parts needed:
■ Home power supply
■ ½" (12.7 mm) UL listed or CSA approved strain reliefs
For vented installations, you will also need:
■ 1 wall or roof cap
■ Metal vent system
For non-vented (recirculating) installations, you will
also need:
■ Chimney Kit Recirculation for non-vented (recirculating)
installations only. See “Assistance or Service” section
to order.
■ Charcoal Filter Part Number W10272069. See “Assistance
or Service” section to order.
Parts supplied:
Remove parts from packages. Check that all parts are included.
■ Hood canopy assembly with ventilator and lights installed
■ Mounting boss/damper/6" (15.2 cm) round flexible metal duct
7" (17.8 cm) long (not expanded)
■ Filter - installed in hood canopy
■ (4) 8 x 80 mm hanger bolts (T20
®
TORX
®
drive)
■ (4) 8 mm x ½" (13 mm) hex nuts
■ (4) 5 x 13 mm mounting screws (T20
®
TORX
®
drive)
■ Mounting template
■ Upper chimney cover
■ Lower chimney cover
■ ½" (13 mm) special nut tightening tool
■ Vent clamp for 6" (15.2 cm) duct
■ (2) 3.5 x 9.5 mm screws used for supporting the lower
chimney (located inside canopy behind filters).
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
Have a qualified technician install the range hood. It is the
installer's responsibility to comply with installation clearances
specified on the model/serial/rating plate. The model/serial/
rating plate is located behind the left filter on the rear wall of
the vent hood.
Canopy hood location should be away from strong draft areas,
such as windows, doors and strong heating vents.
Cabinet opening dimensions that are shown must be used. Given
dimensions provide minimum clearance.
This range hood is recommended for use with cooktops with a
maximum total rating of 78,000 BTUs or less.
Grounded electrical outlet is required. See “Electrical
Requirements” section.
Because of the size and weight of this island hood, the chimney
support must be securely attached to the ceiling.
■ The chimney support must be attached to joists. If this is not
possible, you must build a support structure behind the
plaster or drywall. The support structure must be able to
support 100 lbs (45.4 kg).
The range hood is factory set for venting through the roof or wall.
For non-vented (recirculating) Installation see “Non-vented
(recirculating) Installations” in “Install Range Hood” section.
Chimney Kit Recirculation and Charcoal Filter Kit Part Number
W10272069 are available from your dealer or an authorized parts
distributor. See “Assistance or Service” section to order.
All openings in ceiling and wall where range hood will be installed
must be sealed.
For Mobile Home Installations:
The installation of this range hood must conform to the
Manufactured Home Construction Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction and Safety, Title 24, HUD, Part 280) or when such
standard is not applicable, the standard for Manufactured Home
Installation 1982 (Manufactured Home Sites, Communities and
Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local
codes.
Product Dimensions
†®T20 and TORX are registered trademarks of Acument Intellectual Properties, LLC.
A. 13" (33.0 cm)
B. 11¼" (28.6 cm)
C. 28" (71 cm) min.
45¼" (115 cm) max
D. 2
³⁄₈
" (6.0 cm)
E. 24" (61.0 cm)
F. 36" (91.4 cm)
or 42" (106.7 cm)
B
A
C
D
E
F
Loading ...
Loading ...
Loading ...