Loading ...
Loading ...
Loading ...
Basic operation en
7
7.4 Switching on intensive mode
If particularly strong odours or vapours develop, you
can use intensive mode.
1.
Press repeatedly until LED4 lights up in the LED
display for intensive mode1.
2.
Press repeatedly until LED5 lights up in the LED
display for intensive mode2.
a After approx. 6 minutes, the appliance automatically
switches to fan setting 3.
7.5 Switching off intensive mode
▶
To select a fan setting of your choice, press .
7.6 Switching on the fan run-on
During the fan run-on, the appliance continues to run
for a short time and then switches off automatically.
Note:Further settings are available in the HomeCon-
nectapp.
Requirement:The appliance is switched on.
▶
Press .
a The fan run-on starts at fan setting1.
a The Ambient Light remains switched on for ap-
prox.10minutes.
a The glass panel remains extended halfway.
a The appliance switches off automatically after ap-
prox. 10 minutes.
a The glass panel moves downwards and the appli-
ance closes.
7.7 Switching on automatic mode
1
The optimum fan setting is set automatically using a
sensor.
▶
Press .
Note:In automatic mode, the Guided Air function is al-
ways switched on.
7.8 Switching off automatic mode
1
▶
Press .
a The appliance starts at fan setting2.
a The ventilation is automatically ended when the
sensor detects no further change in the room air
quality.
a Automatic mode runs for a maximum of four hours.
Note:Further settings are available in the HomeCon-
nectapp.
7.9 Intermittent ventilation
With interval ventilation, the ventilation system switches
on and off in the selected setting for the selected time.
Note:This function is only available in the HomeCon-
nectapp.
If the interval ventilation is switched on, LED1 flashes.
7.10 Sensor control
1
In automatic mode, a sensor in the appliance detects
the intensity of the cooking and roasting fumes. De-
pending on the setting of the sensor sensitivity, the op-
timum fan setting is automatically switched on.
If the sensor control system reacts too weakly or too
strongly, the setting for the sensor sensitivity may
change.
¡ Default setting: Fan setting3
¡ Lowest setting: Fan setting1
¡ Highest setting: Fan setting5
7.11 Setting the sensor control
1
Requirement:The appliance is switched on.
1.
Press and hold and for approx.three seconds.
2.
Press or to change the setting.
3.
Press to save the setting.
Or wait approx. fiveseconds until the setting is
saved automatically.
a A signal tone sounds as soon as the selected set-
ting is saved.
7.12 Setting the saturation indicator
The saturation indicator must be adjusted depending
on the filter used.
Requirement:The appliance is switched on.
1.
Press and hold and for approx. 3 seconds.
‒ To set circulating-air mode (Clean Air Standard
circulating-air set or Clean Air Plus circulating-air
set), press and hold / until LED2 lights up in
the LED display.
‒ To set circulating-air mode (regenerable filter),
press / until LED3 lights up in the LED dis-
play.
‒ To convert the electronic control back to opera-
tion without the air recirculation filter, press /
until LED1 lights up on the LED display.
2.
Press to save the setting.
Or wait approx. fiveseconds until the setting is
saved automatically.
a A signal tone sounds as soon as the selected set-
ting is saved.
7.13 Resetting the saturation indicator
After cleaning the grease filter or after changing the
odour filter, the saturation indicator can be reset.
Requirements
¡ After switching off the appliance, the upper two LEDs
for the grease filter's saturation indicator and/or the
lower two LEDs for the odour filter's saturation indic-
ator flash in the left hand control panel.
¡ A signal sounds repeatedly.
▶
Press .
a The saturation indicator is reset.
1
Depending on the appliance specifications
Loading ...
Loading ...
Loading ...