Candy CMCL 5172SKN Refrigerators

User Manual - Page 13

For CMCL 5172SKN.

PDF File Manual, 16 pages, Read Online | Download pdf file

CMCL 5172SKN photo
Loading ...
Loading ...
Loading ...
Clean and dry the interior thoroughly. To
prevent odor and mold growth, leave the door
ajar: block it open or have the door removed if
necessary.
Keep the cleaned appliance in a dry, ventilated
place and away from the heat source, place the
appliance smoothly, and do not place heavy
objects on top of it.
The unit should not be accessible to child’s
play.
Maintenance and cleaning
Before cleaning, unplug the power plug
first; Do not plug in or plug out the plug with
wet hand, because there is a risk of electric
shock and injury. Do not spill water directly on
the refrigerator, to avoid rust, electricity
leakage and accidents. Do not stretch your
hands into the bottom of the refrigerator, since
you might be scratched by sharp metal corners.
Internal cleaning and external cleaning
The food residuals in the refrigerator are liable to
produce bad odor, so the refrigerator must be
cleaned regularly. The fresh food compartment is
usually cleaned once a month.
Remove all shelves, crisper box, bottle racks,
cover board, and drawers etc., and clean them
with a soft towel or sponge dipped in warm
water or neutral detergent.
Clear off the dusts accumulated on the rear panel
and side plates of the refrigerator often.
After using detergent, be sure to rinse it with
clean water, and then wipe it dry.
Do not use bristle brush, steel wire brush,
detergent, soap powder, alkaline detergent,
benzene, gasoline, acid, hot water and other
corrosive or soluble items to cleanse the cabinet
surface, door gasket, plastic decorative parts,
etc., so as to avoid damage.
Carefully wipe dry the door gasket, clean the
groove using a wooden chopstick wrapped with
cotton string. After the cleaning, fix the four
corners of the door gasket first, and then embed
it segment by segment into the door groove.
Interruption of power supply or failure of the
refrigerating system
Take care of the frozen foods in the event of an
extended non-running of the refrigerating
appliance (such as interruption of power supply
or failure of the refrigerating system).
Try to open the refrigerator door as less as
possible, in this way can food safely and freshly
kept for hours even in hot summer.
If you get the power outage notice in advance
1) Adjust the thermostat knob to the high
mode an hour in advance; so that foods get
fully frozen (Do not store new food during
this time!). Restore the temperature mode
to the original setting when power supply
becomes normal in a timely manner.
2) You can also make ice with a watertight
container, and put it in the upper part of the
freezer, so as to extend the time for fresh
food to be stored.
Note: Once the refrigerator is used, you’d
better use it continuously; and under normal
circumstance, do not stop its use, so as not to
affect the service life.
Defrosting
After a period of use, a thin layer of frost will be
formed on the freezer compartment inner wall
(or evaporator) surface, which may affect the
refrigeration effect if exceeding 5mm in thickness.
In such case, you need to gently scrape the frost
off using an ice scraper rather than the metal or
sharp hardware. Frosts need to be cleared off
every 3 months or so, and if the normal use of
drawers and normal access of foods are affected
by frosting, make sure to remove the frosts in a
timely manner. Follow the following steps to
remove frosts:
1. Take out the frozen foods, shut off the mains
power supply, open the refrigerator door,
and gently remove the frosts from the inner
wall with an ice scraper. To speed up the
thawing process, you are suggested to place
a bowl of hot water inside the
refrigerator/freezer, and when the solid ice
frosts become loose, use an ice scraper to
scrape them off and then take them out.
2. After defrosting, clean the
refrigerator/freezer inside, and switch on the
power supply.
Changing the lamp
The LED lamp is used by the refrigerator for
lighting, which features low energy consumption
and long service life. In case of any abnormality,
please contact the after-sales personnel for
visiting service.The lamps can only be replaced by
the manufacturer,together with a part of the
appliance
Safety-check after maintenance
Is the power cord broken or damaged?
Is the power plug firmly inserted into the socket?
Is the power plug abnormally overheat?
Note: Electric shock and fire accident may
be caused in case the power cord and plugs
damaged or stained by dust. If any abnormality,
Loading ...
Loading ...
Loading ...