1. Setup
If numbers are dicult to read
or not visible on screen, plug timer
into an outlet and let timer charge
for 1 hour. Once charged, press
the reset (
r
) button in the lower
left corner using a toothpick
or pencil.
2. Set the time
Use up ( ) and down ( )
arrows to set current time,
take note of AM or PM.
Note: When daylight savings
time occurs use the up
( ) and down ( ) arrows
to adjust the time by 1 hour.
Default “my on”/“my o” Times
Note: To use default times, simply press button so that the
arrow next to the button is visible on the display.
1. Choose your custom “my on time”
2. Choose your custom “my o time”
WARNING
RISK OF ELECTRIC SHOCK
• PLUG DIRECTLY INTO AN ELECTRICAL OUTLET
• DO NOT USE IN WET LOCATIONS
• FULLY INSERT PLUG
• USE INDOORS ONLY
• UNPLUG TIMER BEFORE CLEANING
• KEEP CHILDREN AWAY
RISK OF FIRE
• DO NOT USE TO CONTROL APPLIANCES
THAT CONTAIN HEATING ELEMENTS
(COOKING APPLIANCES, HEATERS, IRONS, ETC.)
• DO NOT EXCEED ELECTRICAL RATINGS
• DO NOT USE WITH EXTENSION CORDS
36253 VERSION 02 06/12/17
Indoor Digital
Simple Set
Plug-In Timer
Press the “my on time” button (the default time will be flashing), then
use the up ( ) and down ( ) arrows to set on time. (If you set the
“my on time” earlier than the current time, it will not turn on until the
next day at the time scheduled.)
Once you reach the desired “my on time,” simply wait 5 seconds,
press the “my on time” button again or press the “my o time” button
to begin setting the o time. Note: Mode indicator will move to “set”
while programming, then back to “clock” once completed.
Press the “my o time” button (the default time will be flashing),
then use the up ( ) and down ( ) arrows to set o time.
Once you reach the desired “my o time,” simply wait 5 seconds,
press the “my o time” button again or press the other “my on
time” button to begin setting the next on time.
Note: When a “my on” or “my o” time is set, the active program
indicator arrow will appear on the screen beside the button (see
Figure 1). Programs may run individually or simultaneously.
FCC Statement
This device complies with Part 15 of the FCC and Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1 this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to
this equipment. Such modifications could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAN ICES-3(B)/NMB-3(B)
MADE IN CHINA
Distributed by Jasco Products Company LLC,
10 E. Memorial Rd., Oklahoma City, OK 73114.
This Jasco product comes with a 1-year limited warranty.
Visit www.byjasco.com for warranty details.
Questions? Contact us at 1-800-654-8483
between 7:00AM–8:00PM CST.
125V~50/60Hz
Maximum load:
15A 1875W resistive
5A 625W tungsten 1/2HP
Suitable for indoor use only.
Works with dimmable LED and CFL bulbs.
I. Initial Setup II. Programming
Reset button
Clears all current times and schedules—
resets timer to factory settings
Up and down arrows
Scroll to set current time and scroll
to set schedule my on/o times
My on/o time
Set custom on/o time
2nd my on/o time
AM/PM Indicator
Active program
indicator arrow
Indicates if program is set
Clock vs. set mode indicator
Figure 1
5:00 p.m.
12:00 a.m.
6:00 p.m.
6:00 a.m.
Loading ...
