Loading ...
Loading ...
Loading ...
240
Looking after your
hand dryer
Please register as a Dyson
hand dryer owner
To help us ensure you receive a prompt
and efficient service, please register your
machine at www.dyson.com/airblade. This
will register your warranty, confirm ownership
of your Dyson machine in the event of an
insurance loss, and enable us to contact you
if necessary.
You will need your serial number, which can
be found on the rating plate inside the main
body and on the information sticker on the
front of the machine.
Please ensure all instructions and guidance in
the Installation instructions and Maintenance
manual are adhered to or your warranty may
be invalidated.
Maintenance
How to use
Place your hands beneath the Dyson
Airblade™ hand dryer arms and it will start
automatically, creating sheets of air that
scrape water from your hands.
For best dry time results:
Keep your hands flat and parallel to the
machine's surface, approximately 0.2in
(5mm) from the air aperture, drawing your
hands through the airflow from your wrists to
finger tips.
Move your hands backwards and forwards
slowly through the air, turning them over
so both back and front are exposed to
the airflow.
Keep your hands flat, close the gaps between
your fingers and keep your thumbs tucked in,
so the whole of your hand is drawn through
the airflow.
For more information about the power
modes, go to www.dyson.com/airblade
Troubleshooting
Hand dryer cuts out
After 30 seconds of continued use the hand
dryer will turn off automatically. Remove and
replace hands to restart.
Turn the machine off and on again at the
mains electricity supply.
Make sure the sensors are clean.
Check the air apertures are clean and free of
dust and blockages. If the air apertures are
dusty, simply remove dust.
Check that the air inlet is free from blockages.
The dry time has increased
Make sure that the correct power mode has
been selected.
Check that the air inlet is free from blockages.
Inspect the air inlets for dust and remove.
The airflow is running
hotter than usual
Check that the air inlet is free from blockages.
Inspect the air inlets for dust and remove.
Air is continuously running
After 30 seconds of continued use the hand
dryer will turn off automatically. Remove and
replace hands to restart.
Check that the air inlet is free from blockages.
Inspect the air inlets for dust and remove.
Contact Dyson for further support
and information or online at
www.dyson.com/airblade
Cleaning
The hand dryer should be cleaned daily.
Wipe the sensors using a soft cloth and non-
abrasive cleaner.
Important information
Do not pressure or power wash the machine.
All cleaning chemicals should be used exactly
as indicated by the manufacturer’s
instructions (including appropriate dilution).
Any chemicals intended for use should
first be tested on an inconspicuous area
to confirm suitability. Aside from cleaning
chemicals, care should be taken to avoid any
harmful fluids from coming into contact with
the product, in particular oils and alcohol-
based products.
Filter maintenance
Regularly check the air inlet to ensure that it is
free from dust and debris. Simply wiping the
inlet with a soft cloth should be sufficient to
remove dust and debris.
If the air inlet gets clogged, further cleaning
or a filter change might be required.
If required for high usage environments, a
Dyson filter change kit provides everything
needed to change your machine’s HEPA
filter on site. Contact the Dyson Helpline for
more information.
Filter cleaning or replacement for your hand
dryer can be carried out by carefully following
the instructions given in the filter change kit. If
in any doubt, consult a qualified electrician or
contact the Dyson Helpline for support.
Servicing
If your hand dryer needs servicing, please
call the Dyson Helpline or visit the website at
www.dyson.com/airblade
07.08.2019 10:12 - C101785-HU03_OPMAN_GLOB_X280-1A-OPMAN-TEXT-101785_15_4c0s
Loading ...
Loading ...
Loading ...