Loading ...
Loading ...
Loading ...
Product Assembly
25
Product Setup - Folding the Treadmill
Step 1: With the treadmill in a folded position, firmly grab the treadmill deck with both hands at the
side rail ends.
Step 2: Slightly push UP on the treadmill deck and use your foot to push forward on the upper part
of the locked cylinder. While continuing to press on the cylinder with your foot, release your
upward effort and move your hands away from the deck.
Step 3: The cylinder is now unlocked and the deck will begin lowering to the floor slowly. Step back
out of the way as the deck lowers to the floor. Your treadmill is now in place and ready to use. No
locking is required.
UNFOLDING THE TREADMILL
Belt Tension and Alignment Adjustment
Proper belt adjustment is important for smooth and safe operation of the treadmill. If the belt is too
loose, you will feel a slight hesitation each time you take a step. The adjustment screws must be
tightened evenly in order to adjust the belt properly. The adjustment screws are located at the rear of
the treadmill in the end caps.
Both adjustment screws should be tightened 1/4 turn in a clockwise direction with a wrench and the
belt checked for slipping after each adjustment. If the belt continues to slip, repeat this process until
the belt stops slipping. Make sure to only turn the adjustment screws 1/4 turn each time until the
slipping stops. This will insure that you do not over-tighten the rollers. Over-tighten the rollers may
cause serious damage to the treadmill.
Belt Alignment
If the belt tracks too close to one side, loosen the adjustment screw on the opposite side, turning it
counterclockwise 1/4 turn. Restart the treadmill and run it at 5 mph / 8 kph for 1 to 2 minutes to insure
the belt will stay in the center. Repeat the procedure if necessary.
If noises develop or malfunctions occur, stop using treadmill and contact BODYCRAFT
Customer Support immediately.
RUNNING BELT TENSION AND ALIGNMENT ADJUSTMENT
25
Lubrication to the deck is very important to your treadmill.
Your treadmill is equipped with a pre-lubricated low friction, reversible deck, that reduces the frictional
forces working against the treadmill’s drive motor. Over time, belt and deck wear due to regular use can
increase friction forces and make your treadmill’s motor work harder. This is true for any motor driven
mechanical device. Keeping friction to a minimum helps extend component life. Additionally, nonuse of
the treadmill for an extended period can lead to a dry deck. If the treadmill belt slows down very quickly
after you have completed your workout, it may lack adequate silicone.
WHY LUBRICATE THE BELT/DECK AREA?
When you need more room in your home or simply want to move your treadmill to another location, it is
very easy to do so with our exclusive Fold-N-Go Feature.
Warning: Before folding the treadmill, make sure the running surface has come to a completed
stop and it is at 0° incline or horizontal position. Do not operate a folded treadmill.
Step 1: While using the proper lifting technique (bend at your knees, use your legs to lift the treadmill, not
your back), firmly grab the treadmill deck with both hands, at the side rail ends.
Step 2: Lift the deck upward.
Step 3: Continue lifting the deck. You will feel the assistance from the cylinder. Lift the deck until it locks in
place. You should be able to see and hear it lock. To verify the cylinder is locked, simply pull down on the
deck. The deck should not move. Your treadmill will remain locked in the upright position.
Product Setup - Moving the Treadmill
This treadmill is equipped with very easy to move transportation system. With the treadmill locked in the
folding position, there are now 4 wheels on the ground. You should be able to grab the treadmill and push it
wherever you would like.
CAUTION: Do not grab the belt itself, as it may roll and you may lose your grip.
Warning: When treadmill is folded, be cautious with young adults, children and
pets playing on, around or underneath the treadmill.
Loading ...
Loading ...
Loading ...