Loading ...
Loading ...
Loading ...
6 49-5000433
Remote Control
Ŷ7RHQVXUHSURSHURSHUDWLRQDLPWKHUHPRWHFRQWURODW
the signal receiver on the air conditioner.
Ŷ0DNHVXUHQRWKLQJLVEHWZHHQWKHDLUFRQGLWLRQHUDQG
the remote control that could block the signal.
Ŷ7KHUHPRWHFRQWUROVLJQDOKDVDUDQJHRIXSWR
20 feet.
Ŷ0DNHVXUHEDWWHULHVDUHIUHVKDQGLQVWDOOHGFRUUHFWO\
as indicated on the remote control.
Ŷ5HPRWHFRQWDLQVDPDJQHWDOORZLQJLWWRDWWDFKWR
metal surfaces.
Cool Mode
8VHWKH&RROPRGHDW/RZ0HG+LJKRU$XWR)DQ
6SHHGIRUFRROLQJ8VHWKH7HPSHUDWXUH,QFUHDVH
Decrease – pads to set the desired temperature between
64°F and 86°F in 1°F increments.
An electronic thermostat is used to maintain the room
temperature. The compressor will cycle on and off
to keep the room at the set level of comfort. Set the
thermostat at a lower number and the indoor air will
become cooler. Set the thermostat at a higher number
and the indoor air will become warmer.
NOTE: If the air conditioner is off and is then turned on
while set to a Cool setting or if turned from a fan setting
to a Cool setting, it may take approximately 3 minutes for
the compressor to start and cooling to begin.
Cooling Descriptions
For Normal Cooling—Select the Cool mode and High
or Med fan with a middle set temperature.
For Maximum Cooling—Select the Cool mode and
High fan with a lower set temperature.
For Quieter and Nighttime Cooling—Select the Cool
mode and Low fan with a middle set temperature.
USING THE AIR CONDITIONER
Controls
Sleep Pad
The SLEEP mode sets the unit to gradually change
settings over an 8 hour period to allow for some
increased energy efficiency during sleep hours.
The SLEEP mode is available only in COOL and
FAN only settings.
Press the SLEEP mode pad and its light will
illuminate. The fan indicator will stay at the same
setting but the air conditioner will automatically
change the FAN speed to low in either COOL or
FAN only mode.
In FAN only mode, the fan will stay in the LOW
speed setting for 8 hours. After 8 hours, the air
conditioner will resume the settings that were in
place before the SLEEP mode pad was pressed.
In COOL mode, the fan will stay in the LOW speed
setting for 8 hours from the time the SLEEP mode
pad was pressed. The air conditioner will also
raise the set point 2°F in 30 minutes and 2°F more
in another 30 minutes where it will remain for the
next 7 hours. After 8 hours, the air conditioner will
resume the settings that were in place before the
SLEEP mode pad was pressed.
While the unit is in SLEEP mode, pressing any pad
will return it to the settings that were in place before
the SLEEP mode pad was pressed.
Control Display On and Off
To reduce brightness during sleeping hours, this
air conditioner control display has an automatic
off feature where the control display will turn off
completely after 5 minute of inactivity. To illuminate
the control interface, press any button on the
control display or remote control. The control
display will illuminate all previously illuminated
LED’s. The control interface will now respond to
any prescribed button press after it is illuminated.
Press and hold the FAN+MODE buttons
simultaneously to toggle this feature ON or OFF.
The LED’s will now stay ON anytime the unit is
ON.
Control Sound On and Off
This air conditioner will make a beep when
the buttons on the control are pushed or if the
unit receives a command from the mobile app
or remote control. To silence these beeps,
simultaneously press the FAN and “-” buttons for 3
seconds. Press these buttons again to toggle the
sound back on.
Loading ...
Loading ...
Loading ...