READ IT OR WATCH IT
Read instructions or watch easy-to-follow video.
Scan QR code or visit http://bit.ly/2VKpTZM
This device complies with Part 15 of the FCC and Industry Canada license-exempt RSS
standards. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy, and if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from which the receiver
is connected.
— Consult the dealer or an experienced radio/TV technician for help.
CAN ICES3(B)/NMB3(B)
Questions? Contact our U.S.-based Consumer Care at 18556988324,
MondayFriday, 7AM8PM CST.
For the most up-to-date product support, accessories, electronic (PDF) format manuals and
more, visit www.byjasco.com/support.
DO NOT RETURN THIS
PRODUCT TO THE STORE
STOP
FCC/IC
SPECIFICATIONS
RISK OF ELECTRICAL SHOCK
• DO NOT USE IN WET LOCATIONS
• USE INDOORS ONLY
• USE ONLY INSULATED STAPLES OR
PLASTIC TIES TO SECURE THE CORDS
• ROUTE AND SECURE THE CORDS SO
THAT THEY WILL NOT BE PINCHED OR
DAMAGED
NO SERVICEABLE PARTS
NON-REPLACEABLE LEDS
LED LIGHT OUTPUT IS STRONG
ENOUGH TO INJURE HUMAN EYES.
PRECAUTIONS MUST BE TAKEN TO
PREVENT LOOKING DIRECTLY AT THE
LEDS WITH UNAIDED EYES FOR MORE
THAN A FEW SECONDS
RISK OF FIRE
• NOT INTENDED FOR ILLUMINATION OF
AQUARIUMS
• NOT INTENDED FOR USE ABOVE
STOVES, COOK TOPS, SINKS OR OTHER
HEAT PRODUCING APPLIANCES, SUCH
AS COFFEE MAKERS, TOASTERS, OR
TOASTER OVENS
• NOT INTENDED FOR RECESSED
INSTALLATION IN CEILINGS OR
SOFFITS
• NOT INTENDED FOR SURFACE
INSTALLATION INSIDE OR ON TOP
OF BUILTIN FURNISHINGS SUCH AS
KITCHEN CABINETS, CHINA CABINETS,
OR TROPHY CASES
• DO NOT CONCEAL POWER SUPPLY
CORD OR LINKING CORDS INSIDE
A WALL, CEILING, SOFFIT, KITCHEN
CABINET, OR SIMILAR PERMANENT
STRUCTURE
• DO NOT RUN THE POWER SUPPLY
CORD OR LINKING CORDS THROUGH
HOLES IN WALLS, CEILINGS OR
FLOORS
WARNING
FIGURE 2
FIGURE 3
INSERT
SLIDE
45415, 45417, 45418
PLUG-IN
LED PUCK LIGHTS
SAVE THESE INSTRUCTIONS IN A LOCATION CLOSE TO YOUR CABINET
SO YOU CAN REFER TO THEM AT A LATER TIME.
WARNINGS TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK
OR INJURY TO PERSONS:
IMPORTANT SAFETY INSTRUCTIONS
This portable light has a polarized plug (one blade is wider than the other) as a feature to reduce
the risk of electric shock. This plug will fit in a polarized outlet only one way. If the plug does not
fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Never
use with an extension cord unless plug can be fully inserted. Do not alter the plug. Read entire
installation procedure before you begin.
INSTALLATION PROCEDURE FOR PLUG-IN UNIT
Carefully plan out your installation prior to securing your LED Puck Light to the mounting
surface, making sure that your 5ft. line cord will reach the nearest electrical outlet. For kitchen
installations, the recommended mounting for the Puck Light is near the front lip of your kitchen
under cabinets as shown in the illustration Figure 1. This provides the best light distribution
across a countertop.
1. DO NOT ATTEMPT TO INSTALL FIXTURE WHILE
PLUGGED IN.
2. Select a suitable dry mounting location (for use
indoors only.) Make sure mounting surface is capable
of supporting the fixture.
3. Locate positions where LED puck should be mounted.
(Keep in mind linking cord.)
4. Use the keyhole taps on the end of the fixture to mark
the appropriate screw hole locations. Pre-drill holes
in the mounting surface with a 1/16” (1.5mm) drill
bit for soft woods and a 3/32” (2.4mm) drill bit for hard
woods. Since mounting is via keyholes, the screw heads
should protrude approximately 1/8” (3.2mm) beyond
surface.
5. After installing mounting screws (included), secure
the LED puck to mounting surface via keyholes by
tightening the mounting screws. See Figure 2 and
Figure 3.
6. Plug fixture into a 120VAC 60Hz outlet.
CLEANING INSTRUCTIONS
Your fixture is made from quality materials that will last for many
years with minimum care. When cleaning, make sure you have
unplugged your fixture and have allowed sufficient time for the
unit to cool to room temperature. You should clean the housing
and lens using a soft, damp cloth. You should plug your fixture
back in only after the fixture has thoroughly dried.
FIGURE 1
CABINET
COUNTER TOP
WALL
The Honeywell Trademark is used under license from Honeywell International Inc.
Honeywell International Inc. makes no representation or warranties with respect to this product.
This product is manufactured by Jasco Products Company LLC.
This Jasco product comes with a limited-lifetime warranty. Visit www.byjasco.com for warranty details.
MADE IN CHINA/HECHO EN CHINA
©JASCO 2019 | 45415, 45417, 45418 | 05/06/19 v1
Jasco Products Company LLC,
10 E. Memorial Road
Oklahoma City, OK 73114
120VAC 60Hz
385 Lumens
83 CRI
2700K Warm White
120VAC 60Hz
775 Lumens
83 CRI
2700K Warm White
120VAC 60Hz
1150 Lumens
83 CRI
2700K Warm White
45415 45417 45418
Loading ...
