Loading ...
Loading ...
Loading ...
Sanitize the dispenser water tanks prior to
installing a full bottle of water for the first time
(see “Cleaning and Sanitizing the Water Tanks”).
IMPORTANT: Make sure the dispenser is unplugged
with both the hot and cold power switches (on the
back of the dispenser, on models so equipped) set to
the O (off) position. Before placing the water bottle
on the dispenser, wash hands and wipe the top of
the bottle with a clean cloth. Avoid touching the part
of the bottle that will be in contact with the water
dispenser.
Make sure the water level in the top of the dispenser
is low enough to allow for proper bottle installation.
Failure to do so may cause the dispenser to overflow.
1. Peel the label from the top cover of the bottle (if
present). Do not remove the entire bottle cap.
2. Place the bottle on top of the dispenser as shown,
aligning the dispensing valve probe
to the center of the water bottle cap. Press down
until the probe penetrates the bottle cap, allowing
the bottle to rest on the support collar.
3. IMPORTANT: Press both dispense buttons until
water runs from both taps.
4. Plug in the dispenser.
5. Set the COLD and HOT power switches (located
on the top left rear of the dispenser,
on models so equipped) to the I (on) position.
6. Allow 30 minutes for water to reach hot
and cold temperatures.
Contact a local water bottle distributor to purchase
water bottles.
Loading the Dispenser and Start Up
Using the water dispenser.
Bottle Support Collar (WS28X10047), grey for models
GXCF05D and GXCC01D
Bottle Support Collar, white (WS28X10049) for models
GXCF20E and GXCF20KWW, black (WS28X10048) for
models GXCF20FBB and GXCF20KBB
Separator (WS28X10013)
Cold Water Tank
Hot (Red) and Cold (Blue) Power Switches (back of
dispenser on equipped models). The Cold (Blue) power
switch also turns on the chiller compartment (on equipped
models).
Indicator Lights. The power indicator light will be lit when the
dispenser is plugged in. The hot and cold indicator lights will
cycle on and off while the dispenser heats
and cools the water. Compressor start maybe delayed
by up to 3 minutes (on certain models).
Hot (Red) and Cold (Blue) Water Dispenser Buttons
Dispenser Drip Tray (WS28X10016) and Grille
(WS28X10015), grey for models GXCF05D and GXCC01D
Dispenser Drip Tray (WS28X10026) and Grille
(SW28X10027), white for models GXCF20E and
GXCF20KWW
Dispenser Drip Tray (WS28X10031) and Grille
(WS28X10034), black for models GXCF20FBB and
GXCF20KBB
Compartment Tray (models GXCF20E/GXCF20FBB/
GXCF20KWW/GXCF20KBB only) (WS29X10029)
Storage Compartment (GXCF05D).
Do not use to store foods requiring refrigeration. The
compartment is not refrigerated.
Chiller Compartment (GXCF20E/GXCF20FBB/
GXCF20KWW/GXCF20KBB).
The compartment is intended solely for use in chilling
canned and boxed beverages, and packaged
nonperishables.
Compartment Shelf (WS28X10028)
Drainage Cap (floor and chiller models) (WS01X10008)
Silicon Stopper (floor and chiller models) (WS01X10007)
Retaining Clip (countertop models) (WS01X10010)
Rubber Drain Cover (countertop models) (WS01X10011)
Features and Parts List
GXCF05D
Storage model
GXCF20E/GXCF20FBB/GXCF20KWW/GXCF20KBB
Chiller model
GXCC01D
Countertop model
4
Loading ...
Loading ...
Loading ...