Dji MATRICE 600

User Manual - Page 2

For MATRICE 600.

PDF File Manual, 3 pages, Read Online | Download pdf file

MATRICE 600 photo
Loading ...
2. Check the motor base for cracks and damage. If wear
exists, but you’re not sure whether it is safe to y,
contact DJI Support for help.
3. Check the connection between the motor base and
the arm tube.
4. Check if the propeller ends on two neighboring
frame arms are aligned. If the vertical difference is
over 1 cm, use the arm inclination holder to adjust
the arm inclination.
IV. Checking the Retractable Landing Gear
1. Check the servo cables for wear. Ensure that the
connection points are secure.
2. Check the power cable connector for wear. Replace
the connector or return to factory for repairs.
3. Hold the aircraft body, and then raise and lower the
landing gear to the ground several times to ensure that
the retractable landing gear can move freely.
4. Check if there is any white plastic debris around the
shaft screws of the landing gear. If there are, replace
the washers under the screws.
5. Checkthepropellers.Ifthereisanybending,breakage
orcracksonapropeller,donotuseit.
6. Attachthepropellertothemotor,turnontheaircraft,
andplaceitontheground.Stand3metersaway
fromtheaircraftandobservethespinningpropellers.
Ifyoucanseetwodistinctpropelleroutlinelayers,
whenlookingataspinningpropellerfromtheside,this
propellerisdamaged.Thiswillincreasetheaircraft
vibrationandreduceightsafetyandperformance.
Replacethepropeller.
VI. Checking the IMU
1. Ensure that your rmware and DJI GO app are up-to-
date. Launch DJI GO app to check the condition of the
IMU and perform an advanced IMU calibration. Place
the aircraft in a cool environment and on a at, stable
surface. Do not touch the aircraft during calibration.
VII. Checking the GPS-Compass Pro
1. Checkthemoduletomakesureitissecurelymounted.
Ensurethatthearrowonitpointstothefrontofthe
aircraft.
2. Ensure that your rmware and DJI Assistant 2 are up-
to-date. Launch DJI Assistant 2 to check the mounting
position settings to ensure that they are correct.
VIII. Checking the Control and Video Transmission System
1. Check the two antennas on the landing gear legs to
ensure that they are secure. Check the antenna cables
at the bottom of the center frame or on the Lightbridge
2 Air System for any bending or damage. Ensure that
they are securely connected. (Note: Attach or detach
the cable in the direction aligned to the connector pin
to avoid damage.)
2. Check the remote controller antennas for damage.
5. Check the shaft screws of the landing gear. If they
are loose, apply high strength threadlocker and then
tighten the screws. It is recommended to afx the
screws with 0.45±0.05 N∙m torque.
V. Checking the Propulsion System
1. Checkthemotorrotorbygentlyshakingitupand
down.Ifitisobviouslyloose,butyou’renotsure
whetheritissafetoy,contactDJISupportforhelp.
2. Checkthemotorsfordeformitiesbyconrmingthatthe
gapbetweenthemotorandmotorbaseiseven,and
themotorspinsfreelyandlooksne.Ifnot,replacethe
motors.
3. Removethepropellersandstartthemotors.Carefully
examinetheedgeofthemotorrotorandconrmthat
theshaftisperfectlycenteredonthemotor.Check
foranyabnormalorexcessivevibration.Ifexcessive
vibrationisdetected,replacethemotors.
4. Removethepropellersandstartthemotors.Listen
carefullyforanyabnormalnoise,whichmayindicate
thatthebearingshavewornoutandthemotorsneed
tobereplaced.
Washers ShaftScrews
DJI Support
http://www.dji.com/support
Recommended Server Center
http://www.dji.com/service/repair
Fordetailsonourafter-salespolicy,visit:
http://www.dji.com/service.
Ifyouareunabletoviewthewebpageorwouldliketo
requestahardcopyofourpolicy,pleasecontactyourlocal
DJIbranchofceorauthorizeddealer.
2
Loading ...