Loading ...
Loading ...
Loading ...
15
USING THE DIGITAL CLOCK (Fig.41)
Power on
Display is flashing
Time of day function
3 button version: press time of day button
2 button version: press both button simultaneous
Set time of day with "+" and "-" buttons.
This function remains activated 7 seconds after the last "+" / "-" operation!
Change Summertime / Wintertime
Activate time of day function; press the button for 4 seconds until the hours display will flash.
Change the hours only by using the “+” or “-“ button. The minutes and hidden seconds will not be affected !
Set timer
This function will be activated with "+" button. Press "+" button again to increase duration time.
During setting the units are 10 seconds steps or minutes.
During count down the timer has priority in the display. The bell- symbol illuminated. The units are seconds or minutes in the
long time section.
The maximum time is 10 h. The format change will happen after 99 minutes and 50 seconds to 1 hour and 40 minutes.
The pot- symbol illuminated.
To show time of day press “time of day” button for 6 seconds.
Reset timer
Count down to zero with permanent pressing “ – “ button. (automatic stop at zero )
Signal
The signal after “time out” will stay 7 minutes if it has not been reset with “time of day” button.
The following signal will be skipped if time of day is pressed during the last 15 seconds of the timer.
Signal frequency
If no function is activated, the signal frequency can be selected by pressing the "-" button.
Three different frequencies (1,5 ; 2,0 ; 3,0kHz) are selectable.
USING THE TOUCH CLOCK (Fig.42)
Mains frequency detection
At power on mains frequency is determined. When the timer is connected to 60Hz, the Celsius symbol is flashing during start-
up.
Power On
At power on, the relay contact is opened. The display and AUTO symbol flashes and time of day starts from 0:00. Power on
state with flashing daytime remains until time of day is set.
Setting Time of Day
Press PLUS and MINUS button simultaneously. At Power On, also MODE button is possible.
Time of day can be set with PLUS or MINUS, while the colon between hours and minutes is flashing.
Quick setting mode starts when PLUS or MINUS is held for more than 1 second. If daytime setting mode is selected while an
automatic program is active, the automatic program is cancelled.
The Buzzer
The buzzer interval alarm signal sounds if minute minder has reached the end time. The signal can be switched off by pressing
any key or by passing the signal duration limit.
Changing the Buzzer frequency
First press Plus and Minus simultaneously (menu far editing the time) and then Mode for selecting the menu far changing the
buzzer frequency. While the text is visible the buzzer signal frequency can be changed by touching Minus repetitively.
Note: If the touch pad is inactive, a visual alarm will only be reset when a valid key combination is pressed far more than 2
seconds.
Clearing Programs and Manual function
The duration of the minute minder can be cleared by
a) "clear Function": First select minute minder program, then press PLUS and MINUS button simultaneously.
after this clear the display returns from adjustment mode to time of day immediately.
b) Back counting of duration to zero. The timer remains in adjustment mode.
Minute Minder
While minute minder mode is selected, the Bell symbol flashes and the display reads the remaining time in hours and minutes,
only if the last minute is counting down the remaining seconds are displayed. An active minute minder program is indicated by
the statically illuminated Bell symbol. If alarm time has finished, an acoustic interval signal sounds and the Bell symbol flashes.
The minute minder program runs independently of other programs.
Key Lock
After power on reset or when no key is pressed for
7
seconds, the key look function is activated. Pressing a valid key or key
combination for 2 seconds or more will deactivate the key lock.
USING THE ANALOG CLOCK (Fig.43)
For setting up the time displayed by watch pointers push briefly twice the knob till getting the CLOCK icon flashing.
For increasing or decreasing time displayed 1 minute by 1, turn the knob clockwise or counterclockwise, le minutes pointer will
increase or decrease 1 minute by minute clockwise or counterclockwise.10 seconds after last set up the electronic timer will exit
time set up mode.Minute minder set up will activate a simple alarm when set up time is over.
Loading ...
Loading ...
Loading ...