Loading ...
Loading ...
Loading ...
7
English
Before starting work, check the setting of the
operation switching device.
If the switching device is not set properly, the nailer
will not operate correctly.
(2) Be careful of double fi re due to recoil. If the Push
Lever is unintentionally allowed to re-contact the
workpiece following recoil, an unwanted fastener will
be driven. In order to avoid this undesirable double
fi re,
○
Intermittent operation (Trigger fi ring)
1) Set the switching device to SINGLE SEQUENTIAL
ACTUATION MECHANISM.
2) Pull the trigger rapidly and fi rmly.
○
Continuous operation (Push lever fi ring)
1) Set the switching device to CONTACT
ACTUATION MECHANISM.
2) Do not press the nailer against the wood with
excessive force.
3) Separate the nailer from the wood as it recoils
after nailing.
(3) Never Use NON relieving coupler on Nailer. If a
non relieving coupler is used on the Nailer, the Nailer
can remain charged with air after disconnecting
and thus will be able to drive a fastener even after
disconnecting. The Nailer and air hose must have a
hose coupling such that all pressure is removed from
the Nailer when the coupling joint is disconnected.
(4) Check Push Lever before use. Make sure the
Push Lever operates properly. (The Push Lever may
be called “Safety”.) Never use the Nailer unless the
Push Lever is operating properly, otherwise the Nailer
could drive a fastener unexpectedly. Do not tamper
with or remove the Push Lever, otherwise the Push
Lever becomes inoperable.
(5) Keep all screws and covers tightly in place. Keep
all screws and covers tightly mounted.
Check their condition periodically. Never use the
Nailer if parts are missing or damaged.
(6) Do not load fasteners with Trigger or Push Lever
depressed. When loading fasteners into the Nailer
or when connecting the air hose,
1) do not depress the Trigger;
2) do not depress the Push Lever; and
3) keep the Nailer pointed downward.
(7) Keep hands and feet away from fi ring head
during use. Never place your hands or feet closer
than 8 inches (200 mm) from the fi ring head. A
serious injury can result if the fasteners are defl ected
by the workpiece, or are driven away from the point of
entry.
(8) Do not drive fasteners into thin boards or near
corners and edges of workpiece.
The fasteners can be driven through or away from the
workpiece and hit someone.
(9) Never drive fasteners from both sides of a wall
at the same time. The fasteners can be driven into
and through the wall and hit a person on the opposite
side.
(10) Check for live wires. Avoid the risk of severe
electrical shock by checking for live electrical wires
that may be hidden by walls, fl oors or ceilings. Turn
off the breaker switch to ensure there are no live
wires.
(11) Never carry Nailer by hose.
(12) Do not disconnect air hose from Nailer with
fi nger on Trigger. The Nailer can fi re when re-
connected to An air supply.
(13) Handle Nailer correctly. Operate the Nailer
according to this Manual. Never allow the Nailer to
be operated by children, individuals unfamiliar with its
operation or unauthorized personnel.
(14) Never use Nailer for applications other than
those specifi ed in this manual.
(15) Never modify or alter a Nailer. Doing so may cause
it to malfunction and personal injuries may result.
(16) Only for installation purpose of pre-punched
holed metal connector to wood stud.
(17) Before each fi ring, be sure to position and insert
the fi rst nail point through the metal hole.
This tool and nails are designed for metal connector
with pre-punched holes.
Drive nails into work surface only; never into materials
too hard to penetrate.
If the nail is not positioned and insert properly, it could
ricochet and hurt yourself or someone.
If you are not sure to position and insert the nail
through the metal hole, never drive nails.
Never drive nails into metal. Only drive into pre-
punched metal holes.
SAFETY — Continued
WARNING
000BookNR65AK2US.indb7000BookNR65AK2US.indb7 2014/01/0912:11:032014/01/0912:11:03
Loading ...
Loading ...
Loading ...