Loading ...
Loading ...
Loading ...
7
3. Press the 0 button repeatedly until ™† ƒ appears
(“medium” water hardness range).
4. Press the @ or A button to change the water hardness range.
Possible values:
5. Press and hold the0 button to exit basic settings.
The change is saved.
Before first use
Before first use, heat the empty appliance for 20 minutes at
100 °C using
è Steam. Do not open the appliance door
during this time. The appliance is automatically calibrated (see
section: Automatic calibration).
1. Fill and insert the water tank (see section: Filling the water
tank).
Before using for the first time, moisten the seal in the tank
cover with a little water.
2. Turn the operating mode selector to è Steam.
3. Turn the temperature selector to 100 °C.
4. Press the n button.
The appliance heats up to 100 °C. The cooking time
(20 minutes) does not start to count down until the set
temperature has been reached. Do not open the appliance
door during this time.
The cooking operation ends automatically and an audible
signal sounds.
5. To switch off the appliance, turn the operating mode and
temperature selectors to
Û.
Leave the appliance door ajar until the appliance has cooled
down.
Cleaning the accessories before use
Using soapy water and a soft cloth, clean the accessories
thoroughly before first use.
Operating the appliance
In this section, you can read about
■ how to fill the water tank
■ how to switch the appliance on and off
■ what to note after each cooking operation
Filling the water tank
When you open the appliance door, you will see the water tank
on the right-hand side.
Caution!
Use of unsuitable liquids may damage the appliance
■ Only use fresh tap water, softened water or uncarbonated
mineral water.
■ If your tap water is very hard, we recommend that you use
softened water.
■ Do not use distilled water, highly chlorinated tap water
(> 40 mg/l) or other liquids.
You can obtain information about your tap water from your
water supplier. The water hardness can be checked with the
test strips enclosed.
Fill the water tank before each use:
1. Open the appliance door and take out the water tank.
2. Fill the water tank with cold water up to the "max" mark.
3. Close the tank cover until you feel it engage.
4. Slide in the water tank until it engages.
Switching on the appliance
1. Turn the operating mode selector to the required operating
mode.
2. Turn the temperature selector to set the temperature.
A default cooking time appears in the display.
3. Use the@ orA button to set the cooking time.
4. Press the n button.
The appliance heats up.
The
t symbol lights up until the set temperature has been
reached and each time the temperature rises.
In the
è Steam operating mode, the cooking time does not
start counting down until the heating-up time has finished.
Changing the temperature
You can change the temperature at any time. To do this, turn
the temperature selector.
Pause
Briefly press the
n button to interrupt cooking (pause). The
cooling fan may continue running. Press the
n button to start.
If you open the appliance door during cooking, operation is
interrupted. Close the appliance door and press the
n button
to restart.
If you have switched on the basic setting "Continue operation
after closing door", restarting is not required (see section:
Basic settings).
Display
Ë
If the water tank is empty, a signal sounds and the
Ë symbol
(Fill water tank) appears. Cooking is interrupted.
1. Open the appliance door carefully.
Hot steam will escape.
2. Remove the water tank, fill up to the "max" mark and slide the
tank back in.
3. Press the n button.
™† ‹
softened -
™† ‚
1-soft I
™† ƒ
2-medium II
™† „
3-hard III
™† …
4-very hard IV
PD[
Operating mode Temperature range
è
Steam 35 - 100 °C
B
Defrosting 35 - 60 °C
Loading ...
Loading ...
Loading ...