Loading ...
Loading ...
Loading ...
7
want continuous power, or when processing items that do not
require an extended amount of blending.
b) Smoothie: start by powering the unit on and pressing Smoothie.
The LED backlight will illuminate and a in under 1 minute count-up
program will begin. Not smooth enough for your liking? After the
cycle stops, the blender will go into Standby mode. To activate
press the Smoothie button again to start a new cycle. An audible
chime will sound at the end of the cycle. You may stop the pro-
gram at any time by pressing the Smoothie button again or by
powering the unit off.
c) Ice Crush: From the Standby mode, press Ice Crush. A pre-pro-
grammed cycle will begin. It is designed to run for approximately
35 seconds and will automatically stop at that point and an
audible chime will sound. The blender will go back into Standby
mode. To start another cycle, press Ice Crush again. To interrupt
the program, press Ice Crush and the unit will pause, reverting to
Standby. To continue, press Ice Crush again. To stop the cycle,
move to another setting or press On/Off. Note: Moving from Ice
Crush to Standby and then holding down the Ice Crush button
momentarily will allow you to operate at a continuous speed
automatically for one minute.
Note: We recommend you use approximately 8 cubes per cycle.
Interrupting any pre-programmed function – Pulse, Smoothie, or
Ice Crush – will reset the program.
9.
TO DISLODGE FOOD
: Use a rubber or plastic spatula to help remove
food lodged around the cutting assembly. DO NOT USE SPATULA UNTIL
YOU HAVE TURNED THE BLENDER OFF. Replace the cover and
measured pour lid and continue blending, if necessary. Make sure spatula
is not inside the blender jar before blending.
10. WHEN FINISHED BLENDING: Press the On/Off button and unplug
the blender from the electrical outlet. Never remove the blender jar
from the motor base until the blender is off. Do not twist locking
ring from blender jar when removing jar from motor base. Simply lift
blender jar from motor base. Do not put hands into blender jar with
blender plugged in.
11. In the event the blender loses power and shuts off, simply unplug the
unit and then plug it back in. Press On/Off to power the unit on. If the
unit has overheated, let it cool down (10 minutes) before powering on.
CLEANING AND MAINTENANCE
Always unplug your Cuisinart
®
PowerEdge
®
1.3 HP Blender from the
electrical outlet before cleaning. The blender is made of corrosion-resistant
parts that are easy to clean. Before first use and after every use, clean each
part thoroughly. Periodically check all parts before reassembly. If any part is
damaged or blender jar is chipped or cracked, DO NOT USE BLENDER.
Remove the blender jar from the motor base by lifting straight up and away.
Invert the jar. Twist off the locking ring by turning counterclockwise. If too
tight, put the unit on the base and twist accordingly (see Helpful Reminders,
page 5).
Remove the cutting assembly and rubber gasket. Wash in warm soapy
water; rinse and dry thoroughly.
Place the blade assembly in the upper rack of the dishwasher or wash in
warm water.
CAUTION: Handle the cutting assembly carefully. It is SHARP and may
cause injury. Do not attempt to remove blades from cutting assembly.
Remove the blender jar cover and the measured pour lid. Wash in warm,
soapy water; rinse and dry thoroughly, or place in upper rack of dishwasher.
The blender jar must be washed in warm, soapy water and rinsed and dried
thoroughly. The blender jar can also be placed upside down in dishwasher.
Finally, wipe the motor base clean with a damp cloth to remove any residue,
and dry thoroughly. Never submerge the motor base in water or other liquid,
or place in a dishwasher.
Tip: You may wish to clean your blender blade assembly as follows:
Squirt a small amount of dishwashing liquid into assembled blender jar
and fill halfway with warm water. Run on Low for 15 seconds. Repeat, using
clean tap water. Empty blender jar and carefully disassemble parts. Any
other servicing should be performed by an authorized service representative.
DOs and DON’Ts WHEN USING YOUR BLENDER
Do:
r .BLFTVSFUIFFMFDUSJDBMPVUMFUJTSBUFEBUUIFTBNFWPMUBHFBTUIBUTUBUFE
on the bottom of the blender motor base.
r "MXBZTVTFUIFCMFOEFSPOBDMFBOTUVSEZBOEESZTVSGBDF
r Always add liquid ingredients to the blender jar first, then add
remaining ingredients. This will ensure that ingredients are
uniformly mixed.
r $VUNPTUGPPETJOUPDVCFTBQQSPYJNBUFMZJODIDNUP
1 inch (2.5 cm) to achieve a more uniform result. Cut all cheeses
into pieces no larger than ½ inch (1.3 cm).
Loading ...
Loading ...
Loading ...