User Manual KitchenAid KSM155GBSR Stand Mixers

KitchenAid KSM155GBSR Stand Mixers - Use Manual - Use Guide PDF.
Documents: Go to donwload!
  • Owner's manual - (English, French, Spanish)

file thumbnail

User Manual for KitchenAid KSM155GBSR

Table of Contents

  • Proof of Purchase and Product Registration
  • Stand Mixer Safety
  • Important Safeguards
  • Electrical Requirements
  • KitchenAid® Stand Mixer Warranty
  • Hassle-Free Replacement Warranty 
  • United States and District of Columbia
  • Hassle-Free Replacement Warranty – Canada
  • How to Arrange for Warranty Service in Puerto Rico
  • How to Arrange for Service after the Warranty Expires – All Locations
  • How to Arrange for Service Outside these Locations
  • How to Order Accessories and Replacement Parts
  • Troubleshooting Problems
  • Tilt-Head Stand Mixer Features
  • Assembling Your Tilt-Head Stand Mixer
  • Using Your Pouring Shield
  • Using Your KitchenAid® Accessories
  • Mixing Time
  • Tilt-Head Stand Mixer Use
  • Care and Cleaning
  • Beater to Bowl Clearance
  • Speed Control Guide
  • Mixing Tips
  • Egg Whites
  • Whipped Cream
  • Attachments and Accessories
  • General Instructions
  • Appetizers and Entrées
  • Yeast Breads and Quick Breads
  • Cakes and Frostings
  • Pies and Desserts
  • Cookies, Bars, and Candies
  • Recipe Index

ASSEMBLING YOUR TILT-HEAD STAND MIXER

To Attach Bowl

  • 1. Turn speed control to OFF.
  • 2. Unplug Stand Mixer or disconnect power.
  • 3. Tilt motor head back.
  • 4. Place bowl on bowl clamping plate.
  • 5. Turn bowl gently into clockwise direction.
  • 6. Plug into a grounded 3 prong outlet.

To Remove Bowl

  • 1. Turn speed control to OFF.
  • 2. Unplug Stand Mixer or disconnect power.
  • 3. Tilt motor head back.
  • 4. Turn bowl counterclockwise.

To Attach Flat Beater, Wire Whip, or Dough Hook

  • 1. Turn speed control to OFF.
  • 2. Unplug Stand Mixer or disconnect power.
  • 3. Tilt motor head back.
  • 4. Slip beater onto beater shaft and press upward as far as possible.
  • 5. Turn beater to right, hooking beater over pin on shaft.
  • 6. Plug into a grounded 3 prong outlet.

To Remove Flat Beater, Wire Whip or Dough Hook

  • 1. Turn speed control to OFF.
  • 2. Unplug Stand Mixer or disconnect power.
  • 3. Tilt motor head back.
  • 4. Press beater upward as far as possible and turn left.
  • 5. Pull beater from beater shaft.

To Operate Speed Control

Speed control lever should always be set on lowest speed for starting, then gradually moved to desired higher speed to avoid splashing ingredients out of bowl. See page 15 for Speed Control Guide.

To Lock Motor Head

  • 1. Make sure motor head is completely down.
  • 2. Place locking lever in LOCK position.
  • 3. Before mixing, test lock by attempting to raise head.

To Unlock Motor Head

  • 1. Place lever in UNLOCK position.

NOTE: Motor head should always be kept in LOCK position when using mixer.

USING YOUR POURING SHIELD*

To Attach Pouring Shield

  • 1. Turn speed control to OFF.
  • 2. Unplug Stand Mixer or disconnect power.
  • 3. Attach Flat Beater, Dough Hook, or Wire Whip and bowl (see page 11).
  • 4. From the front of the mixer, slide the Pouring Shield over the bowl until the shield is centered. The bottom rim of the shield should fit within the bowl.

To Remove Pouring Shield

  • 1. Turn speed control to OFF.
  • 2. Unplug Stand Mixer or disconnect power.
  • 3. Lift the front of the Pouring Shield clear of the bowl rim and pull forward.
  • 4. Remove attachment and bowl.

To Use Pouring Shield

  • 1. For best results, rotate the shield so the motor head covers the “u” shaped gap in the shield. The pouring chute will be just to the right of the attachment hub as you face the mixer.
  • 2. Pour the ingredients into the bowl through the pouring chute.

CARE AND CLEANING

Bowl, white Flat Beater and white Dough Hook may be washed in an automatic dishwasher. Or, clean them thoroughly in hot sudsy water and rinse completely before drying. Wire Whip, burnished Dough Hook and burnished Flat Beater should be hand washed and dried immediately. Do not wash the Wire Whip, burnished Dough Hook and burnished Flat Beater in a dishwasher. Do not store the beaters on the shaft.

NOTE: Always be sure to unplug the Stand Mixer before cleaning. Wipe the Stand Mixer with a soft, damp cloth. Do not use household or commercial cleaners. Do not immerse in water. Wipe off the beater shaft frequently, removing any residue that may accumulate.

BEATER TO BOWL CLEARANCE

Your Stand Mixer is adjusted at the factory so the Flat Beater just clears the bottom of the bowl. If, for any reason, the Flat Beater hits the bottom of the bowl or is too far away from the bowl, you can correct the clearance easily.

  • 1. Turn speed control to OFF.
  • 2. Unplug Stand Mixer or disconnect power.
  • 3. Tilt motor head back.
  • 4. Turn screw (A) SLIGHTLY counterclockwise (left) to raise the Flat Beater or clockwise (right) to lower the Flat Beater.
  • 5. Make adjustment so that the Flat Beater just clears the surface of the bowl. If you over adjust the screw, you may not be able to lock the motor head when it is lowered.

NOTE: When properly adjusted, the Flat Beater will not strike the bottom or side of the bowl. If the Flat Beater or the Wire Whip is adjusted so that it strikes the bowl, the coating may wear off the beater, or the wires on the whip may wear.



Newest Added: KP26M1XGA MMV5219FW KSM150PSER KHM512BY 5VWT51SFYF

Tags: KitchenAid Stand Mixers User Manuals, KitchenAid Stand Mixers Use Manual

KitchenAid KSM155GBSR | Pages: 148 | Created on: 2007-10-08 | File type: PDF | Filename: 85434165_ksm150pser.pdf | Size: 2.56 MB | Language: English, French, Spanish

Download User Manual

Product Infomation and Reviews - KSM155GBSR photo

KSM155GBSR Photo

View more photos

KitchenAid in United States

1 (800) 422-1230, 1 (800) 541-6390 Hours of Operation Mon - Fri: 8 a.m. - 8 p.m. EST