Loading ...
Loading ...
Loading ...
5
6
MODEL: NH11-17-TI MODEL: NH11-17-TI
Cleaning and Maintenance Cleaning and Maintenance
FIRST TIME USE
1. Pull out the power cord from the compartment under the base, and place base on a
at surface.
2. Open the lid then ll water into the kettle.
3. Fill kettle to the maximum level mark (for rst time use only) with fresh tap water.
4. Close the lid and place the kettle back on the base unit, and plug into a power outlet.
5. Switch the kettle on by pressing the switch to the "I" position, the blue LED light
inside the glass jar will illuminate to indicate the water is heating.
6. The kettle will automatically switch to the "O" position once the water has boiled and
the blue LED indicator light has gone o.
NOTE: Wait 30–60 seconds if you need to heat the water immediately after a boiling
cycle.
7. Empty the kettle then wash the glass jar with water, repeat the above
2 times.
NOTE: Never allow the water to ll above the maximum level or lower than the
minimum level indicated on the glass jar.
MAKING TEA
1. Remove tea infuser from kettle by grasping the tea infuser insert and lifting up.
2. Add fresh, cold water to the kettle, lling it for the number of cups of tea you wish to
make—up to 4 cups (max ll for tea is 1 Liter).
3. Insert tea infuser into the kettle and ensure it is securely in place.
4. Once water has boiled, open lid and carefully add tea leaves or tea bags to the
tea infuser. Securely close the lid. Warning: Use extreme caution when adding tea
leaves, unit is very hot.
5. Caution: Wait until unit has completely cooled before removing tea infuser.
Tea infuser will be very hot after use; may cause serious burns if not handled
properly.
GENERAL USE
For everyday use follow steps 1-6 listed above to ensure best results.
NOTE: The power source will only work if the kettle is placed directly on the
base unit. Unplug your unit and allow it to cool before cleaning. Rinse the kettle or
wash with warm soapy water. Wipe the outside of the kettle and base of unit with a
soft, damp cloth. Be sure that the electric kettle socket is kept dry during all cleaning.
Spout Filter – This kettle has a lter to keep the water clean. Run lter under hot water
and gently rub with a clean cloth or brush.
Dry all parts after every use.
Never immerse kettle or power base in water. Any other servicing should be
performed by an authorized service representative.
DE-CALCIFICATION
De-calcication refers to removing mineral deposits, which may form in the interior of
the kettle and may result in discoloration.
To get the best performance from your unit, decalcify your unit from time to time.
Frequency will depend on the hardness of your water and how often you use
the unit.
We suggest using a kettle descaler in order to dissolve these deposits or scale. Follow
the directions on the descaler package.
If a commercial descaler is not available, ll the kettle with enough white vinegar to
cover the bottom by about ½ inch. Heat the vinegar to a boil. Repeat this with cooled
vinegar until all deposits are removed. When the descaling process is complete, empty
the kettle and rinse out several times with clean water.
Note: Reheating tea in your kettle may result in a bronze color tea stain
appearance on the stainless steel surface at the base of the kettle. This is caused
by tea residue that adheres to the bottom of the kettle when reheated at high
temperatures. After a few cycles, the surface of the stainless base may begin to
turn a bronze color. To avoid tea-staining, do not reheat the same pot of tea twice
and always rinse the inside of your kettle before each brew.
To remove the bronze color staining, dilute a small amount of food-grade white
vinegar to a fresh kettle full of water and boil. This will remove the staining and/
or any mineral deposits that may build up in your kettle. After boiling, allow to cool
and thoroughly wash and dry before your next use.
Loading ...
Loading ...