Loading ...
Loading ...
Loading ...
16
S5 Stereo Power Amplifier /M8 Monoblock Power Amplifier
VOLUME +/- Buttons
F
: This function is not used on the S5 and M8. This
function is used on the Michi P5 to increase or decrease the volume of the
Preamplifier. Push or push/hold the button to change the volume.
Main Menu
NETWORK
SETUP
DISPLAY
SYSTEM
Exit
The Setup menu provides access to OSD screens for various configuration
options. Setup menu is reached by pressing the SETUP
B
button on the
remote. To select the desired menu, move the highlight using the
/
D
arrow buttons and press the Enter
K
button on the remote control. Press the
SETUP
B
button again to return to the previous menu or select “EXIT“ on the
OSD to end setup and return to normal operation.
Network Setup
Stativ IP
Disabled
DHCP
NETWORK
SETUP
Status
Renew IP Address
Network Standby
IP Address
Subnet Mask
Network Type
This Network menu in the Setup menu, provides the following options, selected
by placing the highlight on the desired line using the
/
D
arrow buttons
and pressing the Enter
K
button. This action displays the right side options
allowing changes. Change the options using the
/
D
arrow buttons and
press the Enter
K
button to confirm.
Status: If the network is properly configured and attached to the network then
“Connected” will be displayed. If the network is not properly configured or not
connected to a network, “Disconnected“ will be displayed.
Network Type: In most systems, set the IP ADDRESS MODE to DHCP.
This setting will allow your router to assign an IP address to the amplifier
automatically. If your network uses fixed IP addresses, set the IP ADDRESS
MODE to Static. To disable the IP connection set this option to DISABLED.
Options include: DHCP (Default), Static IP, Disabled.
Renew IP Address: Disabled if Network Type is Static or Disabled. If Network
Type is DHCP then select Yes and press the Enter
K
button to renew the IP
address.
Network Standby: When set to ENABLED the amplifier will maintain the
Ethernet IP connection even in Standby Mode allowing the unit to be powered
on via IP. If Disabled the unit will not power on from the IP connection and must
use either the front panel, IR remote or RS232 to power on the unit.
Options Include: Disabled (Default), Enabled.
NOTE When Network Standby is set to ENABLED the unit may consume
more power in standby mode.
IP Address/Subnet Mask/Gateway/DNS: Disabled if Network Type is DHCP
or Disabled. If STATIC mode is selected you must configure all settings for the
network including IP Address, Subnet Mask, Gateway and DNS Server. Press
the Enter
K
button to activates the first digit in the line you want to change,
then use the
/
D
arrow buttons to adjust the values and press the Enter
K
to cycle to the next digit. When the proper IP information is configured
press the Enter
K
button to move the cursor back to the previous menu and
accept the settings. After entering the STATIC IP address information the
network will be tested and connection status reported.
NOTE: For more information regarding network connection please
contact your authorized Michi dealer.
NOTE: A network connection is not required for the amplifier to operate.
Press the SETUP
B
button on the remote control to exit the setup menu or
select “Back” on the OSD to return to the main menu.
Display Configuration
Medium High
DISPLAY
SETUP
Function
Brightness
High
LED Brightness Medium
Back Medium Low
Low
This Display menu in the Setup menu, provides the following options, selected
by placing the highlight on the desired line using the
/
D
arrow buttons
and pressing the Enter
K
button. This action displays the right side options
allowing changes. Change the options using the
/
D
arrow buttons and
press the Enter
K
button to confirm.
Brightness: This function sets the brightness of the front display. The setting
is activated during normal operation by a push release of the DISPLAY button
G
on the remote control. The OSD will always activate at the most bright level
regardless of the Brightness setting to ensure the unit configuration options
can easily be accessed and modified.
Options includes: High (Default), Medium High, Medium, Medium Low, Low.
NOTE To dim the front display PUSH-HOLD the DISPLAY
G
button on
the remote control for 3 seconds.
Loading ...
Loading ...
Loading ...