User Manual - Page 2

For NS-CH1XIS8.

Loading ...
V3 ENGLISH 17-0739
11 Push the wires back in and to the sides to
clear room for the switch.
12 Screw the switch into the wall and attach the
wall plate.
Notes:
If your switch is installed in a row of multiple
switches, you will need to purchase a new face
plate.
Metallic wall plates may block the Wi-Fi signal
from the switch.
13 Turn your circuit breaker on. The switchs LED
blinks green.
SETTING UP YOUR INWALL
SWITCH
Install your switch before following these
instructions.
1 Connect your mobile device to a Wi-Fi network.
2 Type connect.bestbuy.com/setup in the
search bar of your devices browser and follow
the on-screen instructions to download the
app.
3 Open your app and follow the on-screen
instructions to complete setup.
Note: If you plan to access your switch on multiple
devices, you must sign into the same Best Buy
account.
for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20 cm between the
radiator and your body.
CAN ICES-3 (B) NMB-3(B)
Cet appareil radio est conforme au CNR-247d’Industrie Canada.
L’utilisation de ce dispositif est autorisée seulement aux deux
conditions suivantes : (1) il ne doit pas produire de brouillage, et
(2) l’utilisateur du dispositif doit être prêt à accepter tout
brouillage radioélectrique reçu, même si ce brouillage est
susceptible de compromettre le fonctionnement du dispositif.
Cet équipement est conforme aux limites d’exposition aux
rayonnements IC établies pour un environnement non contrôlé.
Cet équipement doit être installé et utilisé avec un minimum de 20
cm de distance entre la source de rayonnement et votre corps.
Use of the Works with Apple HomeKit logo means that an
electronic accessory has been designed to connect specically to
iPod touch, iPhone, or iPad, respectively, and has been certied by
the developer to meet Apple performance standards. Apple is not
responsible for the operation of this device or its compliance with
safety and regulatory standards.
ONEYEAR LIMITED WARRANTY
Visit www.insigniaproducts.com for details.
CONTACT INSIGNIA:
For customer service, call 877-467-4289 (U.S. and
Canada) or 01-800-926-3000 (Mexico)
www.insigniaproducts.com
Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S.
and other countries. App Store is a service mark of Apple Inc.
Google Play and the Google Play logo are trademarks of Google Inc.
INSIGNIA is a trademark of Best Buy and its aliated companies
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2017 Best Buy. All rights reserved
Made in China
PROBLEM
The app or Wi-Fi
cannot nd the
in-wall switch.
POSSIBLE SOLUTIONS
Make sure that your mobile
device and the in-wall switch
are connected to the same
Wi-Fi network and your
network is working properly.
Reset your in-wall switch. Press
and hold the reset button for
15 seconds. The LED ashes
green and the in-wall switch
resets after releasing.
If you are using a metal wall
plate, it may be blocking the
Wi-Fi signal. Use a plastic wall
plate.
Make sure you are using a
2.4GHz Wi-Fi network. A 5GHz
network will not work.
PROBLEM
I can’t nd the
app.
I can’t turn lights
on or o with the
app.
I can't congure
the in-wall
switch.
LED does not
turn On.
How do I do a
Factory Reset?
POSSIBLE SOLUTIONS
Search for "Insignia Connect"
on the Apple App store or
Google Play. Your device must
have iOS 10 or later or Android
6.0.1 Marshmallow or later.
If you are using multiple
mobile devices, make sure
that you’ve signed into the
same Best Buy account on all
your devices.
Use the physical in-wall switch
to make sure that the switch
and light are working.
Press and hold the reset
button for 10 seconds. The
LED ashes green and the
in-wall switch resets after
releasing.
Make sure that the LED is not
deactivated in the app.
Make sure that your switch is
receiving power.
To reset to factory defaults,
press and hold the reset
button for 15 seconds until the
LED blinks.
USING YOUR SWITCH
USING YOUR APP
Use your Insignia Connect app to:
Control lights remotely
Set schedules and a timer
If your switch does not
respond after pressing the
reset button:
1 Remove the wall plate.
2 Insert a paper clip into the
pinhole and press for two
seconds.
3 Press and hold the reset
button for 15 seconds to
factory reset.
4 Replace your wall plate.
LED indicator:
• Solid green: Switch is
connected to the internet
and turned on
• Blinking green: Switch is
not connected to the
internet
• O: LED is disabled in the
app or switch is not turned
on or receiving power
Reset button:
To reset your Wi-Fi, press
and hold for eight
seconds. The LED will
start blinking.
To reset to factory
defaults, press and hold
for 15 seconds. The LED
will be solid and then
start blinking. The
switch will toggle
internally and you will
hear a soft click sound.
Switch button:
Press to turn your
light on or o.
Note: The hardware reset hole can’t
accessed with the wall plate attached.
SPECIFICATIONS
• Dimensions (W×H×D): 1.69 × 2.64 × 1.68 in.
(43 × 67.1× 42.7 mm)
(not including mounting yolks)
• Electrical Rating: 15A, 120V AC, 60Hz
• Resistive: 1800W
• Tungsten: 960W
• Electronic Ballast: 500VA
• General Use
TROUBLESHOOTING
LEGAL NOTICES
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Any changes or modications not expressly approved by the grantee
of this device could void the user’s authority to operate the equipment.
FCC Caution
Changes or modications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
this equipment.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent form
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
To assure continued FCC continued FCC compliance:
Any changes or modications not expressly approved by the grantee
of this device could void the user's authority to operate the equipment.
Industry Canada Compliance
IC Statement
This device complies with Industry Canada’s licence exempt RSSs.
Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference
that may cause undesired operation of the device.
This equipment complies with IC radiation exposure limits set forth
NS-CH1XIS8_NS-CH1XIS8-C_17-0739_QSG_V3_EN.ai 2 9/26/2017 12:30:36 PMNS-CH1XIS8_NS-CH1XIS8-C_17-0739_QSG_V3_EN.ai 2 9/26/2017 12:30:36 PM