Loading ...
Loading ...
Loading ...
6 7
SAFETY WARNINGS FOR
EXTRACTING FOR NUTRIBLASTS
• NUTRIBULLET Rx IS PROGRAMMED TO RUN FOR 1 MINUTE DURING
NUTRIBLAST MODE (G BUTTON WILL BE GREEN).
• IF POWER BASE DOES NOT SHUT OFF AFTER 1 MINUTE DURING NUTRIBLAST
CYCLE, STOP IT MANUALLY BY DEPRESSING THE POWER BUTTON, LOCATED
90˚ TO THE LEFT SIDE OF THE G-BUTTON OR SIMPLY LIFT CUP OFF POWER
BASE.
• TO TURN OFF THE MACHINE AT ANYTIME DURING THE NUTRIBLAST CYCLE (G
BUTTON WILL BE GREEN), DEPRESS THE POWER BUTTON, LOCATED 90˚ TO THE
LEFT SIDE OF THE G-BUTTON OR SIMPLY LIFT THE CUP OFF THE POWER BASE.
IF YOU PRESS THE G BUTTON FOR 2 SECONDS DURING EXTRACTION AND THE
LIGHT TURNS RED, YOU ARE IN SOUPERBLASTER MODE. DEPRESS THE POWER
BUTTON, LOCATED 90˚ TO THE LEFT SIDE OF THE G-BUTTON AND SIMPLY LIFT
THE CUP OFF THE POWER BASE TO TURN OFF THE UNIT. THE LIGHT WILL STOP
GLOWING, SIGNIFYING POWER IS OFF. ALWAYS UNPLUG THE POWER BASE UPON
COMPLETION OF PROCESSING.
• DO NOT TOUCH COUPLING GEAR DIRECTLY WITH HANDS AFTER NUTRIBLAST
MODE! THE COUPLING GEAR IN BLADE BASE AND POWER BASE WILL BE HOT!
• DO NOT RUN IN NUTRIBLAST MODE FOR MORE THAN 1 INTERVAL.
• AFTER INITIAL CYCLE, ALLOW POWER BASE TO SHUT OFF COMPLETELY AND
WAIT FOR 15 SECONDS BEFORE STARTING ANOTHER CYCLE.
• DO NOT RUN FOR MORE THAN 3 CONSECUTIVE 1 MINUTE INTERVALS WITHOUT
ALLOWING POWER BASE TO COOL TO PREVENT OVERHEATING AND ALLOW
INGREDIENTS TO SETTLE FOR 2-3 MINUTES AFTER THE 3RD EXTRACTION CYCLE.
• POWER BASE IS EQUIPPED WITH AN INTERNAL THERMAL BREAKER THAT
SHUTS OFF THE POWER BASE IF THE UNIT OVERHEATS.
• IF THE POWER BASE OVERHEATS AND SHUTS OFF, UNPLUG THE POWER
BASE AND PRESS THE POWER BUTTON, LOCATED 90˚ TO THE LEFT OF THE
G-BUTTON AND LET IT COOL FOR AN HOUR OR MORE BEFORE ATTEMPTING
TO USE IT AGAIN. POWER BASE WILL RESET WHEN THE UNIT IS POWERED OFF
AND THE THERMAL BREAKER HAS COOLED DOWN SUFFICIENTLY.
• WHEN MAKING NUT BUTTERS OR OIL-BASED FOODS, DUE TO THE
CONSISTENCY, THE FOOD WILL PROCESS AND THEN STICK TO THE SIDES OF
THE CUP. PROCESS IN 30 SECOND INCREMENTS ONLY BY SIMPLY LIFTING THE
CUP OFF THE POWER BASE BETWEEN INTERVALS. BETWEEN CYCLES, USE A
COMBINATION OF THE TAP METHOD DESCRIBED ON PAGE 19 AND OPEN CUP
AS NEEDED TO SCRAPE DOWN THE INGREDIENTS TO THE CENTER OF THE CUP
BEFORE CONTINUING TO PROCESS IN 30 SECOND INCREMENTS.
• ALLOW MACHINE TO COOL DOWN FOR 10 MIN AFTER 4-5 CYCLES TO PREVENT
OVERHEATING AND DAMAGING THE UNIT.
• To prevent leakage, always align and hand-tighten or use blade remover to tighten the
blade to the NutriBlast Rx cup prior to inverting it and placing the assembly on to the
motor base.
• TO TURN ON THE NUTRIBULLET: Plug the power base into an electrical outlet.
Press the power button, located 90˚ to the left side of the G-button. This will cause
the power button glow BLUE. Next, place the cup blade-side-down onto the power
base. This will activate the NutriBullet Rx’s SMART Technology function, causing the
G-Button at the front of the unit to glow GREEN.
• Once activated, the unit will run for 1 minute in regular NutriBlast Rx mode before it
automatically turns off. The G-button will stop glowing green at the end of the 1-minute
cycle. To turn off completely before the cycle is complete, either lift the cup off of the
base, or press the power button, located 90˚ to the left side of the G-button. The
power button will extend from its recessed position and the blue light will no longer be
lit, signifying the power is off.
• In NutriBlast Rx Mode, the motor will run 2 cycles during the 1 minute interval— first
it will slow down half way through the 1 minute interval to allow the ingredients to
settle for improved processing, then it will power-up again for the second half of the
interval. This is a normal function of the NutriBullet Rx.
• Turn the NUTRIBULLET Rx off after each use. Depress the power button, located
90˚ to the left side of the G-button. The BLUE light will stop glowing, signifying
power is off.
POWER OFF INSTRUCTIONS
• To turn off the machine at anytime during the NutriBlast cycle (indicated by the
GREEN glowing G-button), depress the power button, located 90˚ to the left side of
the G-button and simply lift the cup off power base. When the vessel is removed
from the power base, only the GREEN G-button light will turn off. When the power off
button is pressed, the BLUE light will turn off and the blade will stop spinning. To turn
off machine at any time during SouperBlast Mode (indicated by the RED glowing G
button), press the power off button, located 90˚ to the left side of the G-button and
simply lift the SouperBlast Pitcher off the power base. When the vessel is removed
from the power base, only the RED G-button light will turn off. When the power off
button is pressed, the BLUE light will turn off and the blade will stop spinning. Always
press the power off button when machine is not in use.
Loading ...
Loading ...
Loading ...