Loading ...
Loading ...
Loading ...
en Operating the appliance
8
Saturation display
If the metal grease filters or the activated charcoal filter
are/is saturated, the corresponding symbols flashes
after the appliance is switched off:
■ Metal grease filters: # and 1
■ Activated charcoal filter: # and 2
■ Metal grease filter and activated charcoal filter: #,
1 and 2
If you have not yet done so, the metal grease filters
should now be cleaned or the activated charcoal filter
replaced. ~ "Cleaning and maintenance" on page 10
Note: The saturation indicator does not apply for non-
renewable activated charcoal filters that are inserted
downstream of the metal grease filter. These activated
charcoal filters must be replaced twice a year.
The saturation indicators can be reset while they are
flashing. To do this, touch the # symbol.
Switching over the display for air recirculation mode
For air recirculation mode, the electronic controller must
be switched over accordingly:
■ The extractor hood must be connected and switched
off.
■ Touch and hold the D symbol. Touch the "2"
symbol.Take your finger off the D symbol. This
will switch the electronic controller over to air
recirculation mode (filters that cannot be
regenerated).
■ Touch and hold the D symbol. Touch the "3"
symbol.Take your finger off the D symbol. This
will switch the electronic controller over to air
recirculation mode (filters that can be regenerated).
■ Repeatedly touching and holding the D symbol
and touching the "1" symbol switches the electronic
controller back over to air extraction mode.
Audible signal
Switching on
Touch and hold the # and y symbols at the same time
for approximately 3 seconds when the fan is switched
off. An audible signal will sound as an
acknowledgement.
Switching off
Touch and hold the # and y symbols at the same time
for approximately 3 seconds when the fan is switched
off. An audible signal will sound as an
acknowledgement.
Operating the appliance en
9
Control panel model 2
Setting the fan
Switching on
Touch the # symbol.
The fan starts at fan setting 2.
Selecting the fan setting
Touch symbol 1, 2 or 3 to set a different fan setting.
Switching off
Touch the # symbol.
Intensive setting
You can use the intensive setting if there is a large
build-up of odours and fumes/vapours.
Switching on
Touch the C or D symbol.
Note: After approx. 6 minutes, the extractor hood
automatically switches back to fan setting 3.
Switching off
If you want to end intensive mode before the preset
time expires, touch the symbol for the required fan
setting.
Fan run-on time
Switching on
Touch the y symbol.
The fan will run at fan setting 1.
After approximately 10 minutes, the fan will switch itself
off automatically.
Switching off
Touch the y symbol.
This immediately stops fan run-on.
Automatic mode
Switching on
1. Touch the # symbol.
The fan will start at setting 2.
2. Touch the > symbol.
The optimum fan setting is set automatically using
the PerfectAir sensor.
Switching off
Touch # or any fan setting to switch off automatic
mode.
The fan switches itself off automatically if the PerfectAir
sensor detects no further change in the air quality in the
room.
Automatic mode can run for a maximum of 4 hours.
Sensor control
In automatic mode, the PerfectAir sensor in the
extractor hood detects the intensity of the cooking and
roasting odours. Depending on the setting of the
PerfectAir sensor, the fan automatically switches itself to
another fan setting.
Possible sensor settings:
Default sensitivity setting: „ (fan setting 3)
Lowest sensitivity setting: ‚ (fan setting 1)
Highest sensitivity setting: † (fan setting D)
If the sensor controller responds too strongly or not
enough, it can be changed accordingly:
1. Touch and hold the > symbol when the fan is
switched off. The setting will be displayed.
2. The sensor controller setting can be changed by
touching symbols 1, 2, 3, C or D.
3. Take your finger off the > symbol.
Symbol Explanation
# Fan on/off
1-3 Fan settings
C Intensive mode 1
D Intensive mode 2
y Fan run-on
> Automatic mode
E Metal grease filter saturation indicator
F Activated charcoal filter saturation indicator
B Light on/off/dimming
Loading ...
Loading ...
Loading ...