Loading ...
Loading ...
Loading ...
7
with "INSERT" (g. 10), then turn the handle to the right
until it is aligned in the "CLOSE" position;
6. Place a recipient under the lter holder and cappuccino
maker (A8) (g. 11);
7. Press the button (B4) corresponding to the
light (g.
12). Delivery begins;
8. When delivery is complete, turn the steam dial (A4) (g.
13) and deliver steam for 10 seconds to rinse the steam
circuit;
9. Repeat points 7 and 8 until you have delivered at least 1
litre of water (about half the tank);
10. Extract the water tank (A17) (g. 3), rinse and ll with fresh
clean water, taking care not to exceed the MAX level (g. 4)
The appliance is ready for use.
Please note: We also recommend rinsing the internal circuits if the appliance is not
used for a long period.
4. ACTIVATING THE WATER SOFTENER FILTER
Certain models are tted with a water softener lter (C6). If this
is not the case with your model, you are recommended to pur-
chase one from De’Longhi Customer Services.
To use the lter correctly, follow the instructions below.
1. Remove the lter from the packaging;
2. Turn the date indicator disk (g. 14) until the next 2 months
of use are displayed;
Please note: The lter lasts about two months if the appliance is used normally. If
the coee machine is left unused with the lter installed, it will last a maximum of 3
weeks.
3. To activate the lter, run tap water through the hole in the
lter (g. 15) until water comes out of the openings at the
side for more than a minute;
4. Extract the tank (A17) (if necessary ll with water);
5. Insert the lter in the water tank and immerse it complete-
ly for about ten seconds, sloping it and pressing it lightly to
enable the air bubbles to escape (g. 16);
6. Place the lter in the lter housing (A18) (g. 17) and press
as far as it will go. Close the tank, then put the tank back
in the machine;
The lter is now active and the coee machine can be used.
5. MENU SETTINGS
Please note: Once in the menu, you can modify all the menu functions as described
in the previous sections.
5.1 Coee temperature
To change the temperature of the water used to make the coee,
proceed as follows:
1. Press and hold the
(B3) and
(B7) buttons together
for at least 3 seconds to access the menu. The
(B15)
and
(B16) lights alternate;
2. Turn the mode selection dial (B8) to the
ESPRESSO po-
sition. The light (B11) remains on steadily;
3. Press the button corresponding to the desired selection as
shown in the following table:
Tasto Temperatura
Normale
Alta
4. To exit the menù, press the (B1) button. (If the appliance
is left idle for
about 1 minute, it exits automatically from
the settings menu and is ready for use again).
5.2 Water hardness
The descale light (B9) comes on after a period of time es-
tablished according to water hardness. The machine can also
be programmed according to the actual hardness of the water
supply in the various regions, in which case descaling may be
required less frequently.
Proceed as follows:
1. Remove the "TOTAL HARDNESS TEST" indicator paper (C4)
from its pack.
2. Immerse the paper completely in a glass of water for one
second.
3. Remove the paper from the water and shake lightly. After
about a minute, 1, 2, 3, or 4 red squares form, depending
on the hardness of the water. Each square corresponds to
one level.
4. Press and hold the
(B3) and
(B7) buttons together
for at least 3 seconds to access the menu. The
(B15)
and
(B16) lights alternate;
5. Turn the mode selector dial (B8) to the
LONG BLACK
position. The
(B9) remains on steadily;
6. Press the button corresponding to the desired selection as
shown in the following table:
Total Hardness Test result Button Level
1
soft water
2
medium
water
3
hard or
very hard
water
7. To exit the menù, press the (B1) button. (If the appliance
is left idle for
about 1 minute, it exits automatically from
the settings menu and is ready for use again).
Loading ...
Loading ...
Loading ...