User Manual Sharp EL2196BL Calculator,

Documents for Sharp EL2196BL

The following documents are available:
User Manual Photos
EL2196BL photo
PRINTED IN CHINA / IMPRESO EN CHINA
04JT(TINSZ0792EHZZ)
04JT(TINSZ0792EHZZ)
INK RIBBON REPLACEMENT
1.Remove the paper roll from the calculator. (Tear the
paper and remove it from the print mechanism by
using .)
2.Turn the power off before replacing ribbon.
3.Remove the printer cover. (Fig. 1)
4.Remove the old ribbon by pulling it up.
5.Insert the new ribbon.
6.With the black side of the ribbon facing upwards,
place one of the reels on the reel shaft on the right.
(Fig. 2) Make sure that the reel is securely in place.
7.Thread the ribbon around the outside of the metal
guides. (Fig. 3)
8.Take up any slack by manually turning one of the
reels.
9.Replace the printer cover. (Fig. 4)
10.Replace the paper roll.
CAMBIO DE LA CINTA ENTINTADA
1.Quitar el rollo de papel de la calculadora. (Cortar el
papel y sacarlo del mecanismo impresor usando
.)
2.Desconecte el aparato antes de cambiar la cinta.
3.Sacar la tapa de la impresora. (Fig. 1)
4.Retire el rollo viejo empujando hacia arriba.
5.Introduzca la cinta nueva.
6.Con el lado negro de la cinta mirando para arriba,
colocar uno de los carretes en el eje del carrete de la
izquierda. (Fig. 2)
Asegurarse de que el carrete esté firmemente
colocado en su lugar.
7.Pasar la cinta por la parte exterior de las quías
metálicas. (Fig. 3)
8.Estirar cualquier parte de cinta floja girando con la
mano uno de los carretes.
9.Volver a poner la tapa de la impresora. (Fig. 4)
10.Volver a poner el rollo de papel.
Nunca introduzca un rollo de papel roto. Esto causará
atascos del papel.
Corte siempre en primer lugar el borde anterior.
1) Introduzca el borde del papel del rollo de papel en la
abertura. (Fig. 1)
2) Conecte la alimentación y haga avanzar el papel
apretando
. (Fig. 2)
3) Introduzca el rollo de papel en el soporte. (Fig. 3)
Never insert paper roll if torn. Doing so will
cause paper to jam.
Always cut leading edge with scissors first.
1) Insert the leading edge of the paper roll into the
opening. (Fig. 1)
2) Turn the power on and feed the paper by pressing .
(Fig. 2)
3) Insert the paper roll to the paper holder. (Fig. 3)
DO NOT PULL PAPER BACKWARDS AS THIS MAY
CAUSE DAMAGE TO PRINTING MECHANISM.
There are several situations which will cause an overflow
or an error condition. When this occurs, “E” will be
displayed. The contents of the memory at the time of the
error are retained.
If an ‘‘0E’’ is displayed at the time of the error, must
be used to clear the calculator. If an ‘‘E’’ with any
numerals except zero is displayed, the error may be
cleared with or and the calculation can still be
continued.
Also, in rare cases, printing may stop midway and the
indication “E” appear on the display. This is not a
malfunction but is caused when the calculator is exposed
to strong electromagnetic noise or static electricity from
an external source. Should this occur, press the key
and then repeat the calculation from the beginning.
Error conditions:
1. Entry of more than 12 digits or 11 decimals. This error
can be cleared with or .
2. When the integer portion of an answer exceeds 12
digits.
3. When the integer portion of the contents of the
memory or grand total memory exceeds12 digits.
(Ex. 999999999999 1 )
4. When any number is divided by zero. (Ex. 5 0 )
Existen diversos casos en los que ocurre un exceso de
capacidad o una condición de error. Al producirse esto,
aparecerá “E”. Los contenidos de la memoria, en el
momento del error, quedan retenidos.
Si, al ocurrir el error, se visualiza el símbolo ‘‘0E’’, se
deberá usar para borrar la calculadora. Si se
visualiza el símbolo ‘‘E’’ con cualquier número (excepto el
cero), se puede borrar el error con o pudiéndose
continuar el cálculo.
Además, en casos muy raros, la impresión puede pararse
en la mitad, y en el visualizador puede aparecer la
indicación “E”. Esto no significa mal funcionamiento, sino
que se debe a que la calculadora ha estado expuesta a
ruido electromagnético intenso o electricidad estática de
una fuente externa. Cuando ocurra esto, presione la
tecla y después repita el cálculo desde el principio.
Condiciones de error:
1. Entrada de más de 12 cifras o de 11 decimales. Este
error puede borrarse con o .
2. Cuando la parte entera de un resultado excede las 12
cifras.
3. Cuando la parte entera del contenido de la memoria o
la memoria del total global supere12 dígitos.
(Ej. 999999999999 1 )
4. Cuando se divide un número cualquiera por un divisor
de cero. (Ej. 5
0 )
Fig. 1 Fig. 2 Fig. 3
Fig. 1 Fig. 2
Fig. 3
PAPER ROLL REPLACEMENT
CAMBIO DEL ROLLO DEL PAPEL
ERRORS ERRORES
A fin de que su calculadora SHARP funcione sin averías,
le recomendamos lo siguiente:
1. Evite dejar la calculadora en ambientes en que haya
cambios de temperatura, humedad y polvo bastante
notables.
2. Al limpiar la calculadora, utilice un paño suave y seco.
No use disolventes ni tampoco un paño húmedo.
3. Debido a que este producto no es a prueba de agua,
no deberá ser utilizado o guardado en lugares donde
pudiera ser salpicado por líquidos, por ejemplo agua.
Gotas de lluvia, salpicaduras de agua, jugos o zumos,
café, vapor, transpiración, etc. también perjudican el
funcionamiento del producto.
4. Si necesita reparar esta unidad, diríjase sólo a un
distribuidor SHARP, a un centro de servicio autorizado
por SHARP o a un centro de reparaciones SHARP.
5. No utilice esta unidad con la lamina aislante fijada; la
lámina aislante impide que la pila se descargue
durante el envío, y se encuentra en la parte posterior
del cuerpo de la unidad. Si no quita la lámina aislante,
tan pronto como se desconecte accidentalmente la
alimentación de CA, se borrarán la fecha y la hora
previamente ajustadas, así como la información sobre
la tasa de impuestos.
6. No bobine el cable de CA alrededor de la calculadora,
y no lo doble o retuerza a la fuerza.
SHARP no será responsable de ningún daño
imprevisto o resultante, en lo económico o en
propiedades, debido al mal uso de este producto y
sus periféricos, a menos que tal responsabilidad sea
reconocida por la ley.
To insure trouble-free operation of your SHARP calculator,
we recommend the following:
1. The calculator should be kept in areas free from
extreme temperature changes, moisture, and dust.
2. A soft, dry cloth should be used to clean the calculator.
Do not use solvents or a wet cloth.
3. Since this product is not waterproof, do not use it or
store it where fluids, for example water, can splash
onto it. Raindrops, water spray, juice, coffee, steam,
perspiration, etc. will also cause malfunction.
4. If service should be required, use only a SHARP
servicing dealer, a SHARP approved service facility or
SHARP repair service.
5. Do not operate this unit with the insulation sheet
attached; the insulation sheet prevents the battery
wear while shipping, and can be found on the back of
the unit's body. If the insulation sheet is not removed,
the previously set date and time, as well as the tax rate
information will be cleared as soon as the AC power is
accidentally unplugged.
6. Do not wind the AC cord around the body or otherwise
forcibly bend or twist it.
SHARP will not be liable nor responsible for any
incidental or consequential economic or property
damage caused by misuse and/or malfunctions of this
product and its peripherals, unless such liability is
acknowledged by law.
OPERATIONAL NOTES
NOTAS AL MANEJARLA
OPERATING CONTROLS CONTROLES DE FUNCIONAMIENTO
“OFF”: Power off.
”:Power ON. Set to the non-print mode.
“P”: Power ON. Set to the print mode.
“P•IC”: Power ON. Set to the print and item count mode.
1) The counter will count the number of times that the
key has been pressed in addition.
Note: Each time the
key is used in subtraction, 1
will be subtracted from the count.
The count is printed when the calculated
result is obtained.
Pressing of the
, , or key clears
the counter.
2) When the grand total/rate setting mode selector is in
the ON position (GT), the counter will count the
number of times that the calculation results have been
stored in the grand total memory. To print and clear the
count, press the key.
3) The memory item counter will count the number of
times that the
key has been pressed in the
addition.
“OFF”: Apagado (OFF)
”: Encendido (ON). Fija el modo de no impresión.
“P”: Encendido (ON). Fija el modo de impresión.
“P•IC”: Encendido (ON). Fija el modo de impresión y de
cuenta de articulos.
1) El contador contará las veces que se ha apretado la
tecla en la suma.
Nota: Cada vez que se use la tecla
en la resta,
se restará 1 de la cuenta.
La cuenta queda impresa cuando se obtiene
el resultado calculado.
Al apretar la tecla , , o se borra
el contenido del contador.
2) Cuando está activado el selector del modo de total
global/fijación de tipos (posición GT), el contador
contará el número de veces que se han almacenado
los resultados de cálculo en la memoria del total
global. Para imprimir y borrar la cuenta, apretar la tecla
.
3) El contador de artículos en memoria contará el número
de veces que la tecla ha sido apretada en la suma.
NO TIRAR DEL PAPEL HACIA ATRÁS PUES PUEDE
OCASIONAR DAÑOS AL MECANISMO DE
IMPRESIÓN.
EL-2196BL
EL-2196BL(U1U)-1
PAPER FEED KEY
LAST DIGIT CORRECTION KEY
GRAND TOTAL KEY
CLEAR ENTRY KEY
TOTAL KEY:
Press this key twice, followed by , to print the set
tax rate.
The tax rate is printed with the symbol “TX”.
MULTIPLICATION KEY
DIVISION KEY
MINUS EQUAL KEY
PLUS EQUAL KEY
CHANGE SIGN KEY
MARKUP KEY
MEMORY TOTAL CLEAR KEY
MEMORY SUBTOTAL RECALL KEY
MEMORY PLUS KEY
MEMORY MINUS KEY
TAX-INCLUDING KEY
PRE-TAX KEY
PERCENT KEY
TECLA DE AVANCE DEL PAPEL
TECLA DE CORRECCIÓN DE LA ULTIMA CIFRA
TECLA DE TOTAL GLOBAL
TECLA DE BORRADO DE ENTRADA
TECLA DE TOTAL:
Presione esta tecla dos veces, seguida por , para
imprimir la tasa de impuestos establecida.
El tasa de impuesto se imprime con el smbolo “TX”.
TECLA DE MULTIPLICACIÓN
TECLA DE DIVISIÓN
TECLA MENOS IGUAL
TECLA MÁS IGUAL
TECLA DE CAMBIO DE SIGNO
TECLA DE USO MÚLTIPLE
TECLA DE TOTAL DE MEMORIA
TECLA DE ACCESO A MEMORIA SUBTOTAL
TECLA DE SUMA EN MEMORIA
TECLA DE RESTA EN MEMORIA
TECLA DE INCLUSIÓN DE IMPUESTOS
TECLA DE ANTES DE IMPUESTOS
TECLA DE PORCENTAJE
1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . ,
1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . ,
1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . ,
1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . ,
1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . ,
1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . ,
1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . ,
1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . ,
1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . ,
1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . ,
1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . ,
ELECTRONIC PRINTING CALCULATOR
CALCULADORA IMPRESORA ELECTRÓNICA
OPERATION MANUAL
MANUAL DE MANEJO
SHARP CORPORATION
WARNING – FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the
manufacturer could void the user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Fig. 4
USING THE CALCULATOR FOR THE FIRST TIME
First, pull out the insulation sheet for the memory
protection battery (installed for retaining the date/time/tax
rate information). Reset the calculator to initialize the
unit's state, then adjust the date and time before using
the calculator.
Removing the insulation sheet, and resetting
1. Pull out the insulation sheet for the memory protection
battery.
2. Press the RESET switch located on the back of the
unit.
(See “RESETTING THE UNIT”.)
* The clock starts, indicating the current date and time
as January 1, 2005, 12:00:00 a.m.
Adjusting date and time
Example: When the date is September 15, 2004, and the
time is 3:38 p.m.
* When the adjustment is complete, the clock starts at
3:38:00 p.m.
UTILIZACIÓN DE LA CALCULADORA POR PRIMERA VEZ
En primer lugar, tire de la lámina aislante para la pila de
protección de la memoria (instalada para conservar la
información sobre la fecha/hora/tasa de impuestos).
Reponga la calculadora para inicializar el estado de la
unidad, y después ajuste la fecha y la hora antes de
utilizarla.
Extracción de la lámina aislante, y reposición
1. Tire de la lámina aislante para la pila de protección de
la memoria.
2. Pulse el interruptor RESET situado en la parte
posterior de la unidad. (Consulte "REPOSICIÓN DE LA
UNIDAD".)
* El reloj se pondrá en funcionamiento, indicando la
fecha y la hora actuales con 1 de enero, 2005,
12:00:00 a.m.
Ajuste de la fecha y la hora
Ejemplo: Cuando la fecha sea el 15 de septiemre de
2004, y la hora las 3:38 p.m.
* Cuando finalice el ajuste, el reloj comenzará a funcionar
a las 3:38:00 p.m.
9 15 2004 9-15-2004
15 38 3-38 00 P
0.
(see “GRAND TOTAL / RATE SETTING MODE
SELECTOR”)
Operation Display
GT
RATE
SET
9 15 2004 9-15-2004
15 38 3-38 00 P
0.
(consulteSELECTOR DEL MODO DE TOTAL
GLOBAL / FIJACIÓN DE TASA)
Operación Visualización
GT
RATE
SET
Note: Each time the key is used in the
subtraction, 1 will be subtracted from the
count.
The count is printed when the memory is
recalled.
Pressing of the key clears the counter.
Note: The counter has a maximum capacity of 3 digits (up
to ±999). If the count exceeds the maximum, the
counter will recount from zero.
DECIMAL SELECTOR:
Presets the number of decimal places in the answer. In
the ‘‘F’’ position, the answer is displayed in the floating
decimal system.
CONSTANT/ADD MODE SELECTOR:
‘‘K’’: The following constant functions will be performed:
Multiplication:
The calculator will automatically remember the first
number entered (the multiplicand) and instruction.
Division:
The calculator will automatically remember the second
number entered (the divisor) and
instruction.
‘‘’’: Neutral
‘‘A’’: Use of the Add mode permits addition and
subtraction of numbers without an entry of the
decimal point. When the Add mode is activated, the
decimal point is automatically positioned according
to the decimal selector setting.
Use of
, and will automatically override the
Add mode and decimally correct answers will be printed
at the preset decimal position.
ROUNDING SELECTOR:
: An answer is rounded up.
5/4: An answer is rounded off.
: An answer is rounded down.
Note: The decimal point floats during successive
calculation by the use of or .
If the decimal selector is set to F then the answer is
always rounded down ( ).
GT: Grand Total
: Neutral
:To set the date, time, and tax rate, set this switch
at the RATE SET position.
Date:
Enter in the order of month, day and year, then
press
to complete the entry.
Use
to separate month, day, and year.
When is pressed, the number entered is
evaluated and displayed as date if the value is
within the following range; Error is displayed
otherwise, and the previously set date is
restored.
Month: 1 - 12; day: 1 - 31; Year: 2000 - 2099 (in
4 digits) or 00 - 99 (in 2 digits)
Time:
Enter in the order of hour, minutes, then press
to complete the entry.
(There is no entry available for the seconds
value. The clock starts at zero second.)
If the hour/minute digit is less than 10, it is not
necessary to enter the first digit 0.
Use to separate hour and minute values.
When is pressed, the number entered is
evaluated and displayed as time if the value is
within the following range; Error is displayed
otherwise, and the previously set time is
restored.
Hour: 0 - 23 (24-hour system for the hour entry),
Minute: 0 - 59
Tax / discount rate:
Press twice, enter the tax rate, followed by
.
Press twice, enter the discount rate,
followed by then .
A maximum of 4 digits can be stored (decimal
point is not counted as a digit).
Note: Be sure to set this selector to the
position after storing an each rate.
Only one rate can be stored. If you enter a
new rate, the previous rate will be cleared.
CLOCK / CALENDAR KEY:
Each time this key is pressed, the mode switches.
Calculation mode Date display mode Clock
display mode Calculation mode
Use this key also to adjust date and time (see
GRAND TOTAL / RATE SETTING MODE
SELECTOR).
Notas: Cada vez que se use la tecla
en la resta,
1 será restado de la cuenta.
La cuenta queda impresa al llamarse la
memoria.
Apretando la tecla se borra el contador.
Nota: El contador tiene una capacidad de un máximo de 3
cifras (hasta ±999). Si la cuenta excede el máximo,
el contador vuelve a contar partiendo de cero.
SELECTOR DECIMAL:
Prefija el número de lugares decimales de la respuesta.
En ‘‘F’’, la respuesta aparecerá en la exhibición en el
sistema decimal flotante.
SELECTOR DEL MODO DE CONSTANTE/SUMA:
‘‘K’’: Se podrán realizar las siguientes funciones de
constantes:
Multiplicación:
La calculadora retendrá automáticamente el primer factor
registrado (el multiplicando) y la instrucción
.
División:
La calculadora retendrá automáticamente el segundo
factor registrado (el divisor) y la instrucción .
‘‘’’: Neutra.
‘‘A’’: Utilizando el modo de suma se pueden sumar y
restar números sin registrar el punto decimal.
Cuando se activa el modo de suma, el punto
decimal se coloca automáticamente de acuerdo con
el ajuste del selector decimal.
El uso de , y desactivará automáticamente el
modo de suma y las respuestas decimalmente correctas
se imprimirán en la posición decimal prefijada.
SELECTOR DE REDONDEO:
: El resultado es redondeado hacia arriba.
5/4: El resultado no es redondeado.
: El resultado es redondeado hacia abajo.
Nota: El punto (= coma) decimal flota mientras se hacen
cálculos sucesivos usando o .
Si el selector decimal se coloca en ‘‘F’’, la respuesta
siempre se redondea por defecto ( ).
GT: Total Global
: Neutra
:Para ajustar la fecha, la hora, y la tasa de
impuestos, ponga este selector en la posición
RATE SET.
Fecha:
Introduzca, por este orden, el mes, el día, y el
año, y después pulse para finalizar la
introducción.
Utilice para separar el mes, el día, y el año.
Cuando pulse , el número introducido se
evaluará y visualizará como fecha si el valor
introducido está dentro del margen; de lo
contrario se visualizará Error, y se
restablecerá la fecha preestablecida.
Mes: 1 - 12; día: 1 - 31; año: 2000 - 2099
(introduzca 4 dígitos) o 00 - 99 (introduzca 2
dígitos)
Hora:
Introduzca, por este orden, la hora y los
minutos, y después pulse para completar la
introducción.
(No es posible introducir los segundos. El reloj
comenzará a funcionar a partir de cero
segundos.)
Si los dígitos de la hora/minutos son inferiores a
10, no será necesario introducir el primer dígito
0.
Utilice para separar los valores de la hora y
los minutos.
Cuando pulse , el número introducido se
evaluará y visualizará como hora si el valor
está dentro de la gama; en caso contrario se
visualizará Error, y se restablecerá la hora
previamente ajustada.
Hora: 0 - 23 (sistema de 24 horas para la
introducción de la hora), Minutos: 0 - 59
Tasa de impuesto / descuento:
Pulse dos veces, introduzca la tasa de
impuesto, seguido por .
Pulse dos veces, introduzca la tasa de
descuento, seguido por y después .
Se puede almacenar un máximo de 4 dígitos (la
coma decimal no cuenta como un dígito).
Nota: Asegúrese de poner este selector en la
posición después de almacenar cada
tipo.
Sólo puede almacenar un tipo. Si introduce
un tipo nuevo, el tipo anterior se borrará.
TECLA DEL RELOJ / CALENDARIO:
Cada vez que pulse esta tecla, el modo cambiará.
Modo de cálculo Modo de visualización de la
fecha Modo de visualización del reloj Modo de
cálculo
Utilice esta tecla para ajustar también la fecha y la
hora (consulte SELECTOR DEL MODO DE TOTAL
GLOBAL / FIJACIÓN DE TASA).
POWER SWITCH; PRINT / ITEM COUNT
MODE SELECTOR:
INTERRUPTOR DE CORRIENTE;
SELECTOR DEL MODO DE IMPRESIÓN /
MODO PARA CONTAR ARTÍCULOS:
TECLA DE NO SUMA/TOTAL PARCIAL:
No-suma – Cuando se aprieta esta tecla
inmediatamente después de haber
ingresado un número en el modo de
impresión, el número registrado se
imprime a la izquierda, junto con el
símbolo #.
Esta tecla se usa para imprimir
números que no están sujetos a
cálculos como, por ejemplo, códigos,
fechas, etc.
Total parcial – Se usa para obtener uno o varios
totales parciales de sumas y/o
restas.
Cuando se aprieta a continuación de
la tecla o , se imprimirá el
total parcial junto con el símbolo
pudiéndose seguir con los cálculos.
Al apretar esta tecla, incluso en el modo de no
impresión, se imprimirá el número que aparece
en la exhibición con el símbolo “P”.
Cuando el INTERRUPTOR DE LA ALIMENTACIÓN;
SELECTOR DEL MODO DE IMPRESIÓN / MODO
PARA CONTAR ARTÍCULOS esté en la posición “•”
o P o PIC, y esté visualizándose la fecha o la
hora, pulse esta tecla para imprimir el contenido
visualizado, incluyendo el símbolo #, desde el
lado derecho del rollo de papel.
Ejemplo:
Impresión de la fecha
#9 15 2004
(cuando la fecha sea el 15 desetiembre de 2004)
Impresión del reloj
#10 30 A
(cuando la hora sea 10:30 a.m.)
#6 25 ------------
P
(cuando la hora sea 6:25 p.m.)
Cuando finalice la impresión de la fecha / hora,
volverá al modo de cálculo.
SÍMBOLOS DEL VISUALIZADOR:
M:Un número ha sido guardado en la memoria.
–:El valor del display es negativo.
E:Error ó desbordamiento de la capacidad.
: Aparece cuando un número está en la memoria de
total global.
NON-ADD/SUBTOTAL KEY:
Non-add – When this key is pressed right after an
entry of a number in the Print mode, the
entry is printed on the left-hand side with
the symbol #.
This key is used to print out numbers not
subjects to calculation such as code,
date, etc.
Subtotal – Used to get subtotal(s) of additions and/
or subtractions. When pressed following
the or key, the subtotal is printed
with the symbol
and the calculation
may be continued.
By pressing this key even in the Non-print mode,
the displayed number is printed with the symbol
“P”.
When the POWER SWITCH; PRINT / ITEM
COUNT MODE SELECTOR is set “•”, P or PIC
position, and Date or Clock is displayed, press this
key to print the displayed contents, including #
symbol, from the left side of the paper roll.
Example:
Date printing
#9 15 2004
(when the date is September 15, 2004)
Clock printing
#10 30 A
(when the time is 10:30 a.m.)
#6 25 ------------ P
(when the time is 6:25 p.m.)
When the Date / Clock printing is complete, the
Calculation mode is restored.
DISPLAY SYMBOLS:
M:A number has been stored in memory.
–:The display value is negative.
E:Error or overflow of capacity.
: Appears when a number is in the grand total memory.
GRAND TOTAL/RATE SETTING MODE
SELECTOR:
SELECTOR DEL MODO DE TOTAL GLOBAL/
FIJACIÓN DE TASA:
EL-2196BL(U1U)(表面) 04.10.15, 2:01 PMPage 1 AdobePageMaker6.0J/PPC
Loading ...