Loading ...
Loading ...
3
ASSEMBLY INSTRUCTIONS
Cabinet Use Requirements
■ Intended for use in a garage.
■ Maximum weight limit is 45 lbs (20.5 kg) for each shelf.
■ Maximum weight limit is 225 lbs (102.3 kg) for the cabinet.
Unpack Cabinet Parts
1. Remove and verify the contents. Contents include a hex key, a
key, and the parts and fasteners shown in “Parts.”
2. Dispose of/recycle all packaging materials.
Assemble Cabinet
Gather the required tools before starting installation.
Tools Needed:
Tools Supplied:
IMPORTANT:
■ Two people may be required to complete the assembly.
■ As you assemble the cabinet, make sure the edges with the
holes are facing up.
■ If you are assembling the cabinet on the floor, fasten the eight
front corner bolts, two at each corner, after you stand the cabinet
upright.
1. Place side panel (P1) on a flat, firm surface so that the edge with
the holes is facing up as shown.
2. Insert the cabinet top (P2) between the edges of side panel (P1).
NOTE: Make sure the edges with the holes are facing up.
3. Align the holes and attach the top (P2) to side panel (P1) using
six Hex-head bolts (F1) and two ⁵⁄₁₆"
flange nuts (F2) as shown.
Do not tighten completely.
4. Position the other side panel (P1) so that the top (P2) is between
the edges of side panel (P1).
5. Align the holes and attach the top (P2) to the side (P1) using six
Hex-head bolts (F1) and two ⁵⁄₁₆"
flange nuts (F2) as shown. Do
not tighten completely.
6. Insert the cabinet bottom (P3) between the edges of the side
panels (P1).
NOTE: Make sure the edges with the holes are facing up.
7. Align the holes and attach the bottom (P3) to the sides (P1) using
six Hex-head bolts (F1) and two ⁵⁄₁₆"
flange nuts (F2) for each side
as shown. Do not tighten completely.
Attach Back Panels
IMPORTANT:
■ Attach the back panels starting at the top of the cabinet with
back panel (AAA) and working down to the cabinet bottom. Each
back panel will overlap the panel below.
■ Do not completely tighten the screws until all back panels are in
place.
1. Align back panel (AAA) with the holes in the cabinet top. Using
seven Phillips-head screws (F3c), attach back panel (AAA) to the
cabinet top and sides.
2. Slide the top of back panel (BBB) under the bottom of back panel
(AAA). Using four Phillips-head screws, fasten back panel (BBB)
to the cabinet sides.
3. Repeat Step 2 for the remaining back panels ending with back
panel (EEE).
4. Using two Phillips-head screws, attach each back panel to the
panel below.
NOTE: Using three Phillips-head screws, attach panel (EEE) to
the cabinet bottom (P3).
5. Completely tighten all back panel screws starting with the sides
and continuing with the top, middle and bottom.
F1 F2
F1
⁵⁄₁₆
" Hex-head bolt (24)
F2
⁵⁄₁₆
" Flange nut (8)
■ ¹⁄₂" Wrench
■ ³⁄₈" Wrench
■ Phillips screwdriver
■ Level
■ Hex key ■ Key
WARNING
Excessive Weight Hazard
Use two or more people to move, assemble or install
cabinet.
Failure to do so can result in back or other injury.
F3c
Phillips-head screw (34)
P1
P1
P2
P3
P1
P2
Loading ...
Loading ...
Loading ...