Loading ...
Loading ...
Loading ...
5
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools
listed here.
Tools needed:
■ Level
■ Drill with 1
1
/
4
" (3.0 cm) and
3
/
16
" (5.0 mm) drill bits
■ Pencil
■ Wire stripper or utility knife
■ Tape measure or ruler
■ Pliers
■ Caulking gun and weatherproof caulking compound
■ Vent clamps
■ Jigsaw or keyhole saw
■ Flat-blade screwdriver
■ Metal snips
■ Phillips screwdriver
■ TORX
®†
T20
®†
bit or driver
Parts needed:
For hard wire installations, you will also need:
■ Home power supply cable
■
1
/
2
" (12.7 mm) UL listed or CSA approved strain relief
For vented installations, you will also need:
■ 1 wall or roof cap
■ Metal vent system
For non-vented (recirculating) installations, you will
also need:
■ Chimney Kit Recirculation for non-vented (recirculating)
installations only. See the “Assistance or Service” section to
order.
■ Charcoal Filter Kit Part Number W10272069.
See the “Assistance or Service” section to order.
Parts supplied:
Remove parts from packages. Check that all parts are included.
■ Hood canopy assembly with ventilator and lights installed
■ Vent mounting boss (attached to hood canopy assembly)
■ Damper
■ 3 - 3.5 x 9.5 mm screws damper to mounting boss
■ Metal grease filter installed in hood canopy
■ Chimney cover support bracket
■ 2-piece chimney cover
■ 2 - 8 x 80 mm hanger bolts (TORX
®
T20
®
drive)
■ 2 - 8 mm nuts
■ 2 - flat washers
■ 2 - 5 x 40 mm TORX
®
T20
®
drive screws for chimney
bracket mounting.
■ 2 - 5 mm wall anchors
■
1
/
2
" (13 mm) special nut tightening tool
■ 2 - plastic spacers for lower chimney
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
Have a qualified technician install the range hood. It is the
installer’s responsibility to comply with installation clearances
specified on the model/serial/rating plate. The model/serial/
rating plate is located behind the left filter on the rear wall of
the vent hood.
Canopy hood location should be away from strong draft
areas, such as windows, doors, and strong heating vents.
Cabinet opening dimensions that are shown must be used.
Given dimensions provide minimum clearance.
The canopy hood mounting location must be capable
of supporting 100 lbs (45.4 kg).
This range hood is recommended for use with cooktops
with a maximum total rating of 78,000 BTUs or less.
Grounded electrical outlet is required. See the “Electrical
Requirements” section.
For non-vented (recirculating) Installation see “Non-vented
(recirculating) Installations” in the “Install Range Hood” section.
Chimney Kit Recirculation and Charcoal Filter Kit Part Number
W10272069 are available from your dealer or an authorized parts
distributor. See the “Assistance or Service” section to order.
All openings in ceiling and wall where canopy hood will be
installed must be sealed.
For Mobile Home Installations:
The installation of this range hood must conform to the
Manufactured Home Construction Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction and Safety, Title 24, HUD, Part 280) or when such
standard is not applicable, the standard for Manufactured Home
Installation 1982 (Manufactured Home Sites, Communities
and Setups) ANSI A225.1/NFPA 501A or latest edition, or
with local codes.
Product Dimensions
G
F
E
D
C
B
A
A. 12
3
/
8
" (31.4 cm)
B. 13
1
/
8
" (33.4 cm)
C. 36" (91.4 cm)
D. 19
3
/
4
" (50.1 cm)
E. 2
3
/
8
" (6.0 cm)
F. 25
9
/
16
" (65.0 cm)
G. 33
7
/
8
" (86.0 cm) min.
55
1
/
2
" (141.0 cm) max.
TORX and †®T20 are registered trademarks of Acument Intellectual Properties, LLC.
Loading ...
Loading ...
Loading ...