Loading ...
Loading ...
Loading ...
26
GAS CONVERSION PROCEDURE
10. Re-fit oven supply pipe to burner and replace
the backpanel.
11. Place gas sticker supplied onto rear panel over
existing sticker.
12. Remove the regulator and replace with test point
adaptor supplied for ULP or propane. For NG
remove test point adaptor and replace with regulator
supplied. Note that ULP and propane both use the
same test point adaptor.
13. Turn on gas & check for leaks.
14. Check and adjust the test point pressure according
to the procedure in the installation instructions.
15. Light all burners and operate at maximum.
16. For each hotplate and grill burner adjust the burner
to minimum and screw in the bypass screw until
a small stable flame results. Adjust the burner to
maximum and back to minimum to ensure correct
adjustment.
17. Re-fit the control panel & re-connect to electrical
power.
1. Turn off gas supply to appliance.
2. Disconnect appliance from electrical power
(if applicable).
3. Pull off control knobs and remove control panel
(two screws).
4. Remove grill burner injector and replace with
appropriate injector.
5. Fit aeration control (shutter) supplied to grill burner
as required. See page 10 of instruction book for
grill shutter assembly diagram. Note that ULP and
propane use the same aeration control.
6. Remove existing hotplate injectors and fit appropriate
injectors supplied.
7. Remove by pass screw in oven thermostat and fit
appropriate by pass screw supplied. Note that ULP
and propane use the same by-pass screw.
8. Remove backpanel and disengage oven supply pipe
from oven burner.
9. Remove oven injector and replace with injector
supplied.
INJECTORS NATURAL GAS UNIVERSAL LPG PROPANE
Wok burner 1.75 mm 1.00 mm 0.95 mm
Large hotplate burner 1.60 mm 0.90 mm 0.95 mm
Medium hotplate burner 1.35 mm 0.70 mm 0.82 mm
Small hotplate burner 1.00 mm 0.55 mm 0.62 mm
Grill burner 1.50 mm 0.82 mm 0.82 mm
Oven burner 1.60 mm 0.82 mm 0.95 mm
Thermostat Bypass Screw 0.73 mm 0.45 mm 0.45 mm
Regulator NG Regulator
LP Test Point
Adaptor
LP Test Point
Adaptor
27GAS CONVERSION PROCEDURETROUBLE SHOOTING
If you have a problem with your appliance check the following before you ring the service line.
PROBLEM WHAT TO DO
Operational problems
i.e. Oven, grill or hob
not working
Check the electricity is turned on
Check your fuses. If the fuse continues to blow, call the Service Centre
Check the circuit breaker
Ensure correct knob is turned
Gas only – Dry or clean ignition electrodes
Gas only – Make sure flame ports and ignition areas are clean and dry
Gas only – Check gas supply is on
Gas only – Ensure cap/crown correctly fitted
Replace or tighten light globes (where fitted)
Heat up problems
Oven not pre-heated – Pre-heat oven for 30 minutes
Check oven door is closed properly
Remove foil or trays from bottom of oven
Change set oven temperature
Preheat your oven/grill before you put the food in to be cooked
Unit smoking odours
New appliances can have an odour during first operation. It is recommended to ‘run
in’ the oven before you cook. Run the oven at 180ºC for two hours and ensure room
is well ventilated
For products with separate grill compartment, run the grill on for full for 15 minutes
with grill door open
Persistent gas smell – do not operate appliance. Call service 131349
Condensation NOTE: some
condensation is normal and is
to be expected during cooking
Reduce the amount of water used for cooking
Leave the door open after cooking if food remains in cooker for warming
Timer not audible Turn Timer knob past 15 minute mark then to the required number of minutes
Oven shelf tight Remove shelf and insert as per diagram
Oven or grill not working
(Electric cooker only)
Clock not set, refer to clock instructions
Oven not working Clock program set. Cancel program
Oven light not working Lamp blown or loose in socket. Replace or tighten globe
Electronic clock flashing
on display or off (Electric
cooker only)
Check household power supply, fuses and reset time of the day
Powerpoints not working (NZ
model Electric cooker only)
Check the fuse at rear and replace if blown
Gas oven burner uneven flame
This does not affect cooking results. From cold start the oven burner flame will be
higher on the left-hand side. After reaching the set temperature, the flame will then
be even.
The oven seal is loose
The oven seal is only attached at each corner. It may seem like a loose fit, but when
the oven door is closed it will function correctly.
TROUBLE SHOOTING
TIPS & INFORMATION
TIPS AND INFORMATION
When you need information, service or replacements
please quote:
1. Model Number.
2. Serial Number: You can find these on the data plate,
which can be seen when the oven door is open. If you
need more information, please contact the Customer
Care Centre on 1300 363 640 (Australia – Centre is
open 8.00am to 5.00pm Monday to Friday EST).
Or +649 573 2384 (New Zealand – Centre is open 8.00am
to 5.00pm Monday to Friday). Only authorised service
centres should carry out servicing. Otherwise warranty
may be void. If you have a warranty or spare parts
enquiry, you should call the numbers listed on the
back page.
Loading ...
Loading ...