READ IT OR WATCH IT
Read instructions or watch easy-to-follow video.
Scan QR code or visit http://bit.ly/2RwbICT
44105 (12IN.), 44106 (18IN.), 44107 (24IN.),
44108 (36IN.)
PLUG-IN LED LIGHT FIXTURE
SAVE THESE INSTRUCTIONS FOR POSSIBLE FUTURE USE.
CAUTION: DO NOT USE POWER TOOLS TO SECURE SCREWS, AS
THERE IS A RISK OF STRIPPING THE SCREWS.
DO NOT USE WITH A DIMMER OR DIMMING CIRCUIT.
DO NOT EXCEED THE MAXIMUM CONNECTED UNITS INDICATED ON
THE POWER ADAPTER/LED DRIVER.
IMPORTANT SAFETY INSTRUCTIONS
The LED light fixture has a polarized plug (one blade is wider than the other) to reduce the risk of
electric shock. This plug fits in a polarized outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not alter the plug.
Read entire installation instructions before you begin.
INSTALLATION PROCEDURE FOR PLUG-IN LIGHT FIXTURE
This device complies with Part 15 of the FCC and Industry Canada license-exempt RSS
standards. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy, and if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from which the receiver
is connected.
— Consult the dealer or an experienced radio/TV technician for help.
CAN ICES-3(B)/NMB-3(B)
Questions? Contact our U.S.-based Consumer Care at 1-855-698-8324,
Monday–Friday, 7AM–8PM CST.
For the most up-to-date product support, accessories, electronic (PDF) format manuals and
more, visit www.byjasco.com/support.
DO NOT RETURN THIS
PRODUCT TO THE STORE
STOP
FCC/IC - EN
SPECIFICATIONS
The Honeywell trademark is used under license from Honeywell International Inc.
Honeywell International Inc. makes no representation or warranties with respect to this product.
This product is manufactured by Jasco Products Company LLC.
This Jasco product comes with a limited-lifetime warranty. Visit www.byjasco.com for warranty details.
MADE IN CHINA/HECHO EN CHINA
©JASCO 2019 | 44105, 44106, 44107, 44108 | 06/26/19 v1
Jasco Products Company LLC.
10 E. Memorial Road
Oklahoma City, OK 73114
120VAC 60Hz
8.9W
375 Lumens
83 CRI
2700K White
120VAC 60Hz
13W
575 Lumens
83 CRI
2700K White
120VAC 60Hz
14.5W
750 Lumens
83 CRI
2700K White
44105 (12IN.) 44106 (18IN.) 44107 (24IN.)
FIGURE 1
CABINET
COUNTER TOP
WALL
3 Pin
18” linking cord
Power Adapter
LED Light Fixture
ON/OFF switch
18” linking
cord
mounting holes
DO NOT exceed maximum units as indicated on power adapter.
120VAC 60Hz
19.5W
1150 Lumens
83 CRI
2700K White
44108 (36IN.)
RISK OF ELECTRICAL SHOCK
• DO NOT USE IN WET LOCATIONS
• USE INDOORS ONLY
• USE ONLY INSULATED STAPLES OR
PLASTIC TIES TO SECURE THE CORDS
• ROUTE AND SECURE THE CORDS SO
THAT THEY WILL NOT BE PINCHED OR
DAMAGED
NO SERVICEABLE PARTS
NON-REPLACEABLE LEDS
LED LIGHT OUTPUT IS STRONG
ENOUGH TO INJURE HUMAN EYES.
PRECAUTIONS MUST BE TAKEN TO
PREVENT LOOKING DIRECTLY AT THE
LEDS WITH UNAIDED EYES FOR MORE
THAN A FEW SECONDS
RISK OF FIRE
• NOT INTENDED FOR ILLUMINATION OF
AQUARIUMS
• NOT INTENDED FOR USE ABOVE
STOVES, COOK TOPS, SINKS OR OTHER
HEAT PRODUCING APPLIANCES, SUCH
AS COFFEE MAKERS, TOASTERS, OR
TOASTER OVENS
• NOT INTENDED FOR RECESSED
INSTALLATION IN CEILINGS OR
SOFFITS
• NOT INTENDED FOR SURFACE
INSTALLATION INSIDE OR ON TOP
OF BUILT-IN FURNISHINGS SUCH AS
KITCHEN CABINETS, CHINA CABINETS,
OR TROPHY CASES
• DO NOT CONCEAL POWER SUPPLY
CORD OR LINKING CORDS INSIDE
A WALL, CEILING, SOFFIT, KITCHEN
CABINET, OR SIMILAR PERMANENT
STRUCTURE
• DO NOT RUN THE POWER SUPPLY
CORD OR LINKING CORDS THROUGH
HOLES IN WALLS, CEILINGS OR
FLOORS
WARNING
Carefully plan your installation prior to mounting the LED light
fixture. For kitchen installations, the recommended mounting
for the LED light fixture is under the cabinets near the front lip,
as shown in Figure 1. This provides the best light distribution
across a countertop. Make sure that the power supply cord
will reach the nearest electrical outlet, and that the power
adapter and the 18in. LED light fixture cord will reach the first
fixture. See Figure 4 for layout of components and all electrical
connections.
1. DO NOT ATTEMPT TO INSTALL FIXTURE WHILE
PLUGGED IN.
2. Select a suitable dry mounting location (for use indoors
only). Make sure mounting surface is capable of
supporting the LED light fixture.
3. Locate position where the LED light fixture should be
mounted.
4. Use the keyhole tabs on the end of the fixture to mark
the appropriate screw hole locations. Pre-drill holes in
the mounting surface with a 1/16in. (1.5mm) drill bit for
soft woods and a 3/32in. (2.4mm) drill bit for hard
woods. Since mounting is via keyholes, the screw heads
should protrude approximately 1/8in. (3.2mm) beyond
surface.
5. After installing mounting screws (included), secure the
LED light fixture to mounting surface via keyholes. See
Figure 2 and Figure 3.
6. Your line cord has a molded plug on one end and a
link connector at the other end. The link connector
plugs into your LED light fixture. The second cord
provided is a linking cord with link connectors on both
ends. This is used to connect your LED light bar to the
next light fixture in your chain. Link adjacent LED light
fixtures only. See Figure 4 below to see how the 2-pin
and 3-pin plugs are intended to be used.
FIGURE 3
INSERT
SLIDE
FIGURE 2
FIGURE 4
FIGURE 5
7. Attach the quick-connect power cord with the plugand
3-pin quick connector to the LED light fixture closest
to the outlet. See Figure 4 and Figure 5.
8. Repeat steps 1 through 8 for additional LED light
fixtures, making sure they are within 18in. of each
other so that they can be connected by the provided
18in. linking cord. Note: DO NOT connect more than
the maximum units indicated on the power adapter/
LED driver.
9. Use the provided 18in. linking cords to connect
the LED light fixtures together by inserting the male
end of the linking cord into the corresponding female
connection point on each LED light fixture.
10. Plug LED light fixture into a 120VAC 60Hz outlet.
INSTALLATION INSTRUCTIONS FOR ATTACHING ADDITIONAL LED
LIGHT FIXTURES AT A LATER DATE
If you desire additional LED light fixtures for your system after the initial installation, you may
attach them as needed (sold separately) by following these instructions. Keep in mind the
maximum linking distance between fixtures is 18in. DO NOT exceed the maximum units as
indicated on the power adapter/LED driver.
CAUTION: DO NOT ATTEMPT TO ATTACH ADDITIONAL LED LIGHT FIXTURES TO YOUR
EXISTING SYSTEM WITHOUT UNPLUGGING THE LINE CORD FROM THE ELECTRICAL
OUTLET OR DISCONNECTING THE ELECTRICITY AT THE ELECTRICAL POWER PANEL.
A. Install additional LED light fixtures following steps 1-10 of the mounting instructions.
B. Once installed, attach the 18in. linking cord between the last LED light fixture (previously
installed) and the new one. See Figure 4 for layout of components and all electrical
connections.
C. When adding LED light fixtures to an existing system of linked light fixtures, the line cord
(with the power plug) and power adapter are not needed. Only the first light fixture in the
chain needs to be connected to power adapter with the line cord. Please note that the switch
only controls a single LED light fixture. It does not control other linked LED light fixtures.
D Additional linking cords can be purchased on Amazon, part number 47167 (12in.), 47168
(18in.), 47169 (24in.), 47170 (36in.), 47172 (48in.), 47171 (60in.), 47173 (120in.).
Loading ...
Loading ...
Loading ...
