Loading ...
Loading ...
Loading ...
9
CAUTION
If ignition does NOT occur in 5 seconds, turn the
control knob OFF, wait 5 minutes and repeat the
lighting procedure. If the burner does not ignite with
the valve open, gas will continue to flow out of the
burner and could accidently ignite with risk of injury.
Turn control knob and LP cylinder OFF when not in
use.
WARNING
Ignitor Lighting
• Do not lean over appliance while lighting.
1. Turn ON LP gas cylinder.
2. Press and turn the control knob to
3. Turn ROTARY IGNITOR knob rapidly.
4. If ignition does not occur in 5 seconds, turn the burner control
knob OFF, wait 5 minutes, and repeat lighting procedure.
If ignition still does not occur, follow match-lighting
instructions.
Match-Lighting
Do not lean over appliance while lighting.
1. Turn ON LP cylinder.
2. Swing match hole plate to expose match lighting hole. Place
lit match into match lighting hole of appliance as pictured
below. Make sure lit match is placed inside hole and near
burner.
3. Push in and turn control knob to Be sure burner lights and
stays lit.
4. Once lit, swing match hole plate back to cover up match
lighting hole. Caution: Plate maybe hot.
View is from side of appliance
Turning Appliance Off
• Turn control knob to position. Turn LP cylinder off by OFF
turning hand-wheel clockwise to a full stop.
Ignitor Check
• Turn gas off at LP cylinder. Turn ignitor knob. "Click" should be
heard each time at electrode. See "Troubleshooting" if no click or
spark.
Valve Check
• Important: Make sure gas is off at LP cylinder before
checking valve. Knob locks in position. To check valve, OFF
first push in knob and release, knob should spring back. If knob
does not spring back, replace valve assembly before using this
appliance. Turn knob to position then turn back to OFF
position. Valve should turn smoothly.
Hose Check
• Before each use, check to see if hose is cut, worn or kinked.
Replace damaged hose before using applaince. Use only
valve/hose/regulator specified by manufacturer.
General Appliance Cleaning
• Meat Thermometer: Do not immerse or soak in water. Wash
with warm soapy water and wipe dry.
• Do not mistake brown or black accumulation of grease and
smoke for paint. Interiors are not painted at the factory (and
should never be painted). Apply a strong solution of detergent
and water or use a grill cleaner with scrub brush on insides of
appliance lid and bottom. Rinse and allow to completely air dry.
Do not apply a caustic grill/oven cleaner to painted surfaces.
A black surface improves the appliances performance.
• Plastic parts: Wash with warm soapy water and wipe dry.
Do not use citrisol, abrasive cleaners, degreasers or a
concentrated grill cleaner on plastic parts. Damage to and failure
of parts can result.
• Painted surfaces: Wash with mild detergent or non-abrasive
cleaner and warm soapy water. Wipe dry with a soft non-
abrasive cloth.
• Stainless steel surfaces: To maintain the high quality
appearance, wash with mild detergent and warm soapy water
and wipe dry with a soft cloth after each use. Baked-on grease
deposits may require the use of an abrasive plastic cleaning pad.
Use only in direction of brushed finish to avoid damage. Do not
use abrasive pad on areas with graphics.
Burner Flame Check
• Light burner. Looking through viewing hole on top of appliance,
you should see the flame height as shown below. Turn control
knob from to OFF. The Flame height should decrease
and then go out. Always check flame prior to each use. If only
low flame is seen refer to "Sudden drop or low flame" in the
Troubleshooting Section.
Normal
Hose
Kinked
Hose
High Flame
Low Flame
High Flame
Control
Knob
Swing Plate to
expose
Matchlighting
Hole
Match Hole
Plate
Match
Lighting
Hole
Match
Loading ...
Loading ...
Loading ...