Loading ...
Loading ...
8
tween the surfaces of the appliance and the side and rear
walls and at least 15 cm above the coee maker.
Connecting the appliance
Danger!
Check that the mains power supply voltage corresponds to that
indicated on the rating plate on the bottom of the appliance.
Connect the appliance to an eciently earthed and correctly
installed socket with a minimum current rating of 10A only. If
the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualied
professional.
FILLING THE WATER TANK
1. Open the lid (g. 1) and extract the tank by pulling it up-
wards (g. 2);
2. Fill the tank with fresh clean water, taking care not to ex-
ceed the MAX level (g. 3). Put the tank back in the ap-
pliance, pressing lightly to open the valves located on the
bottom of the tank;
3. More simply, the tank can also be lled without extracting
it by pouring the water directly from a jug.
Important:
Never operate the appliance without water in the tank or with-
out the tank. Check the water level in the water tank by the
display (A11).
SETTING UP THE APPLIANCE
1. Turn the knob to ON position to switch on the applice (g.
4): the ON pilot light turns on;
2. Insert the required coee lter (1 or 2 cups) in the lter
holder (g. 5);
3. Attach the lter holder onto the machine without lling it
with ground coee (g. 6);
4. Place a 0.5 l / 17 oz container under the boiler outlet and
another 0.5 l / 0.5 l / 17 oz container under the cappuccino
maker (g. 7);
5. Wait until the READY light comes on (g. 8) and immedi-
ately afterwards turn the selector dial to the
posi-
tion (g. 9) and let about half the tank discharge from the
boiler outlet;
6. Then turn the steam dial to the
position (g. 10)
and discharge all the water remaining in the tank from the
cappuccino maker;
7. Turn the steam dial back to the 0 position and the selector
dial to the ON position;
8. Empty the two containers and replace them under the
boiler outlet and the cappuccino maker and repeat points
5-6-7.
Now the appliance is ready for use.
Important!
No water is delivered or pump is too noisy: make sure the
tank is lled and placed correctly and repeat the operation till
water is delivered.
Tips for a hotter coee
To make espresso coee at the right temperature, the coee
maker should be preheated as follows:
1. Turn the appliance on by turning the selector dial to ON
position (the ON light comes on) (g. 4) and attach the l-
ter holder onto the appliance without adding pre-ground
coee (g. 6);
2. Place a cup under the lter holder. Use the same cup to be
used later to prepare the coee, in order to preheat it;
3. Wait until the READY light comes on (g. 8) and imme-
diately afterwards turn the selector dial to the
position (g. 9) and let water discharge until the READY
light turns o, then interrupt by turning the dial to the ON
position.
4. Empty the cup, wait until the READY light comes on again
and then repeat the same operation.
(It is normal for a small and harmless pu of steam to be given
o when removing the lter holder).
Use of the mug or high glass tray
When using mugs or high glasses (for example, if you prepare
long coee or latte macchiato), remove the drip tray and put the
mug/glass on the tray (A13 -g. 11). Once nished the prepara-
tion, put the drip tray back in place.
HOW TO MAKE ESPRESSO COFFEE USING PRE-
GROUND COFFEE
1. Place the ground coee lter (C2 or C3) in the lter holder
To make one coee, use the lter with the symbol
on the bottom, to make two coees, use the lter with the
symbol on the bottom;
2. To make just one coee, place one level measure of pre-
ground coee (about 7 g/0,25 oz) in the lter (g. 12). To
make two coees, place two loosely lled measures (about
6+6 g/0,21 + 0,21 oz) of pre-ground coee in the lter. Fill
the lter a little at a time to prevent the pre-ground coee
from overowing;
Important: For correct operation, before lling with pre-ground coee,
make sure there are no coee residues left in the lter from the last time you made
coee.
Loading ...
Loading ...
Loading ...