User Manual Hoover BH53420 Onepwr Evolve Cordless Upright Vacuum

• Owner's manual - (English, French, Spanish)

Table of contents

• ASSEMBLY INSTRUCTIONS
• CHARGING THE BATTERY
• PRODUCT OVERVIEW
• OPERATION
• USING THE ONEPWR™ DUST CHASER™ HAND VACUUM
• EMPTYING THE DIRT CUP
• CLEANING THE FILTER AND SEPARATOR
• REMOVING AND REPLACING THE BRUSH ROLL
• CLEANING THE DUST CHASER™ HAND VACUUM FILTER
• TROUBLESHOOTING
• ACCESSORIES

USER MANUAL Cordless Upright Vacuum

ASSEMBLY INSTRUCTIONS

1.Install the wand into the body until it clicks into place (A). If your model comes with the Dust Chaser Hand Vacuum, first connect the adapter into the body until it clicks into place (B).

2. Push the hand vacuum onto the adapter until it clicks into place.

3. Attach the battery pack by aligning the ribs on the battery pack to the grooves in the product. Slide the battery pack into the product until it clicks into place.

CHARGING THE BATTERY

1.Plug the charger into a power outlet.

2. Attach the battery pack to the charger by aligning the ribs on the battery pack to the grooves in the charger. Slide the battery pack into the charger.

3. When charging, the lights on the battery wilt illuminate to show the state of charge. If the light on the charger flashes red, there is an error with the battery or the charger. Try again or call customer service for support. Once charge is complete, lights on the battery will turn off.

4. To remove the battery pack from the charger, press the latches and pull the battery away from the charger.

PRODUCT OVERVIEW

Comfort Grip Handle Wand 0N/0FF Button Mode Buttons & LED Mode Display ONEPWR™ Battery Filter/Separator Access Easy Empty Dirt Cup Dirt Cup Empty Button Hose Release Removable Brush Roll

ON/OFF Button Mode Button LED Mode Display

Comfort Grip Handle 0N/0FF Button ONEPWR™ Battery Filter Access Separator Access Dirt Cup Release Button

OPERATION

1.Press the ON/OFF button located on the shoulder. The ON/OFF button and mode Indicator lights will Illuminate when ON.

2. To change modes, press the Mode button on the shoulder. The mode Indicators will Illuminate, telling you which mode you are In. • Evolve defaults to Multi-Surface Mode. This mode works well on all floor types and preserves runtime. • Use Carpet Mode for deep cleaning on carpets with high suction. • Use Brush Mode Off on delicate floor types. This mode has high suction with the brush roll off.

3. Step on the nozzle of the product and pull back handle to recline and begin cleaning.

USING THE ONEPWR™ DUST CHASER™ HAND VACUUM

1.To use the hand vacuum for above floor cleaning. depress the hand vacuum release button and pull the hand vacuum upwards. off the adapter.

2. Remove the battery from the Evolve upright and insert into the hand vacuum.

3. Press the ON/OFF button located on the top of the hand vacuum.

4. For detailed cleaning. choose an accessory and push the accessory anto the end of the hand vacuum.

5. To remove the accessory. pull out.

EMPTYING THE DIRT CUP

1.Remove the battery pack

2. Push down the latch on the dirt cup to release. Rock the dirt cup backwards off the body

3. Hold the dirt cup over a trash bin and press the dirt cup release button to empty.

4. To close, push the door until it locks back into place.

5. Replace the dirt cup by aligning the bottom first and then rocking it into place.

CLEANING THE FILTER AND SEPARATOR

1.Open the dirt cup lid to access the filter and separator.

2. To clean the separator, lift to remove. Clean dirt and debris by wiping tbe metal screen with a cloth and then place back into the dirt cup.

3. Pull the filter away and tap over a trash can to remove dirt. Rinse filter under warm water until water comes out clear. Allow filter to air dry for at least 24 hours until fully dry.

REMOVING AND REPLACING THE BRUSH ROLL

1.Remove the battery. Using your fingers or a coin, push and turn the brush rail lock counterclockwise to release the brush roll.

2. Pull the brush roll out of the nozzle with the pull tab.

3. To remove any threads or hair. slide the blade of a pair of scissors into the groove of the brush roll and cut along the groove.
Clear any dirt/debris from the end caps and inside the housing of the nozzle.

4. Re-fit the brush roll into the nozzle and turn the brush roll lock clockwise to lock.

CLEANING THE DUST CHASER™ HAND VACUUM FILTER

1.Remove the battery pack.

2. Hip the unit over so you can see the bottom on the hand vacuum.

3. Pinch the filter access door lever and pull out.

4. Pull the filter away (A). Fold the foam piece back (B) and then tap over a trash can to remove dirt.

5. Rinse filter and foam piece under warm water until water is clear. Allow to air dry for at least 24 hours until fully dry.

TROUBLESHOOTING

THIS PRODUCT CONTAINS NO SERVICEABLE PARTS.

IF APPLIANCE IS NOT WORKING AS IT SHOULD, HAS BEEN DROPPED. DAMAGED. LEFT OUTDOORS. OR DROPPED INTO WATER. CALL CUSTOMER SERVICE AT 1-800-406-2005 PRIOR TO CONTINUING USE.

ACCESSORIES