Loading ...
Operation Guide 5627
E-19
Fishing/Moon Mode
The Fishing/Moon Mode displays an indicator that shows,
as one of five levels, the suitability of a specific date and
time (minute 00 to minute 59 of a particular hour) for
fishing. This mode also can be used to display Moon Data
(Moon age and Moon phase) for a specific date.
x If you doubt that the fishing level indicator or current
Moon data is wrong for some reason, check the
current Timekeeping Mode settings (time, date, and
Home Site), and correct them if required.
x See “Moon Phase Indicator” (page E-42) for
information about the Moon phase indicator.
x All of the operations in this section are performed in
the Fishing/Moon Mode, which you enter by pressing
C
(page E-6).
Time
Fishing level indicator
Year Month – Day
Moon phase indicator
E-18
4. Press
A
to exit the setting screen.
x The watch will automatically adjust the minute hand slightly to match its internal
second count when you exit the setting screen.
x To return to the Timekeeping Mode, press
C
.
E-17
To adjust the analog time
1. In the Timekeeping Mode, press
C
six times to enter
the Hand Setting Mode (page E-7).
2. Hold down
A
until the current digital time starts to
flash, which indicates the analog setting screen.
3. Press
D
to advance the analog time setting by
20seconds.
x Holding down
D
advances the analog time setting
at high speed.
x If you need to advance the analog time setting a long way, hold down
D
until the time starts advancing at high speed, and then press
B
. This locks
the highspeed hand movement, so you can release the two buttons. High-
speed hand movement continues until you press any button. It will also stop
automatically after the time advances 12 hours or if an alarm (multi-function
alarm, Hourly Time Signal, or countdown beeper) starts to sound.
E-16
To toggle between 12-hour and 24-hour timekeeping
In the Timekeeping Mode, press
D
to toggle between 12-hour timekeeping and
24-hour timekeeping.
x With the 12-hour format, the P (PM) indicator appears to the left of the hour
digits for times in the range of noon to 11:59 p.m. and no indicator appears to
the left of the hour digits for times in the range of midnight to 11:59 a.m.
x With the 24-hour format, times are displayed in the range of 0:00 to 23:59,
without any indicator.
x The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
x The P indicator is not displayed with the Timekeeping Mode time on the
Countdown Timer Mode and Dual Time Mode screens.
Setting the Analog Time
Perform the procedure below when the time indicated by the analog hands does not
match the time of the digital display.
E-15
4. When the setting you want to change is flashing, use
D
and
B
to change it as
described below.
Setting Screen Button Operations
UTC Differential
Use
D
(+) and
B
(–) to change the setting.
x You can specify a value in the range of –12.0 to
+14.0, in 0.5-hour units.
Longitude Value
Use
D
(+) and
B
(–) to change the setting.
x You can specify a value in the range of 0° to 180°,
in 1-degree units.
East Longitude/
West Longitude
Use
D
to switch between east longitude (E) and
west longitude (W).
x When the digital time DST setting is on, the UTC differential can be set in a
range of –11.0 to +15.0 in 0.5-hour units.
5. Press
A
to exit the setting screen.
E-14
To configure Home Site data
1. In the Timekeeping Mode, hold down
A
until the
seconds start to flash, which indicates the setting
screen.
2. Press
A
again to display the UTC differential setting
screen.
3. Press
C
to move the flashing in the sequence shown
below to select other settings.
UTC
Differential
Longitude
Value
East Longitude/
West Longitude
C
C
C
UTC differential
E-13
Home Site Data
Moon phase, the fishing level indicator, and Fishing/Moon Mode data will not
be displayed properly unless Home Site data (UTC differential and longitude) is
configured correctly.
x The UTC differential is a value that indicates the time difference between
a reference point in Greenwich, England and the time zone where a city is
located.
x The letters “UTC” is the abbreviation for “Coordinated Universal Time”,
which is the world-wide scientific standard of timekeeping. It is based upon
carefully maintained atomic (cesium) clocks that keep time accurately to within
microseconds. Leap seconds are added or subtracted as necessary to keep
UTC in sync with the Earth’s rotation.
x The “Site Data List” at the back of this manual provides UTC differential,
latitude, and longitude information around the world.
x The following is the initial factory default Home Site data (Tokyo, Japan) when
you first purchase the watch, and whenever you have the battery replaced.
Change these settings to match the area where you normally use the watch.
UTC differential (+9.0); Longitude (East 140 degrees)
E-12
To toggle the Timekeeping Mode digital time between DST and Standard Time
1. In the Timekeeping Mode, hold down
A
until the
seconds start to flash, which indicates the setting
screen.
2. Press
C
once to display the DST setting screen.
3. Press
D
to toggle between Daylight Saving Time (On
displayed) and Standard Time (OF displayed).
4. Press
A
twice to exit the setting screen.
x The DST indicator appears on the Timekeeping,
Fishing/Moon, Alarm, and Hand Setting Mode screens
to indicate that Daylight Saving Time is turned on. In
the case of the Fishing/Moon Mode, the DST indicator
appears on the fishing level screen only.
On/Off status
DST indicator
E-11
x Resetting the seconds only (without changing the DST, hour, or minute setting)
causes the analog minute hand setting to be adjusted automatically.
x See “Digital Time Daylight Saving Time (DST) Setting” below for details about
the DST setting.
x The day of the week is displayed automatically in accordance with the date
(year, month, and day) settings.
Digital Time Daylight Saving Time (DST) Setting
Daylight Saving Time (summer time) advances the digital time setting by one hour
from Standard Time. Remember that not all countries or even local areas use
Daylight Saving Time.
E-10
3. When the setting you want to change is flashing, use
B
and
D
to change it as
described below.
Screen To do this: Do this:
Reset the seconds to 00
Press
D
.
Toggle between Daylight Saving Time
(On) and Standard Time (OF)
Press
D
.
Change the hour or minutes
Use
D
(+) and
B
(–).
Change the year
Change the month or day
4. Press
A
twice to exit the setting screen.
x The first press of
A
displays the UTC differential setting screen. Pressing
A
again exits the setting screen.
Loading ...
Loading ...
Loading ...