Loading ...
Loading ...
Loading ...
6. It is not recommended to open the door of your machine while the activated wash program is running. Even so if the door is opened and not closed within
approximately 4 seconds, the unit will not continue the wash program. In this case, you must close the door and press the “START/PAUSE” button again to
continue the wash program.
CANCELLING A WASH PROGRAM:
1. Press and hold the “START/PAUSE” button for approximately 3 seconds.
2. The display will show “1” to confirm the cancellation of the wash program.
Note: If the door is opened during the canceling process, the door must be closed within 4 seconds to continue the canceling process.
If the door is not closed during the 4 seconds, close the door and simply press the “START/PAUSE” button again to continue the cancelling process of the wash
program.
SELECTING AN OPTIONAL WASH OPTION:
1. Select the desired Pre-Programmed Wash Program as directed above.
2. Before pressing the “START/PAUSE” BUTTON, press the “OPTIONS” button.
3. Continue to press until the indicator light of the option (Half-Load or Hi-Temp) you desire is illuminated.
4. Press the Extra button in order to choose from Sanitize / Extra Rinse / Extra Dry options.
5. Close the door of your appliance and press the “START / PAUSE” button to activate the wash program.
Wash Options:
HALF LOAD:
This option allows you to save energy and wash a smaller load. This option should be used when washing less than a full load or in the event you do not want to
load the washer and run later when completely loaded.
SANITIZE:
When the Sanitize option is selected, the water temperature will be maintained at 156ºF/69ºC (maximum). The maximum temperature may not be reached if the
incoming water temperature is not adequate. Residential dishwashers are not intended for licensed food establishments or Commercial applications.
HI-TEMP:
When the HI-Temp option is selected, the water temperature will be maintained at 140ºF/60ºC (maximum). The maximum temperature may not be reached if the
incoming water temperature is not adequate. Residential dishwashers are not intended for licensed food establishments or Commercial applications.
EXTRA DRY:
When the EXTRA DRY option is selected, the machine changes the water temperature for each program and the extra dry is performed.
EXTRA RINSE:
When the EXTRA RINSE option is selected, washing-rinsing steps will be added into the selected program so you can ensure that your dishes will be extra clean
and glossier.
DELAY:
To delay the start of a selected cycle, press the Delay Start button until the desired delay time shows in the LED display. You can delay the start time from 1 to 19
hours. To cancel the delay start option before the set delay period is over, simply press and hold the DELAY button for approximately 3 seconds.
1. Select the desired Pre-Programmed Wash Program as directed above.
2. Before pressing the “START/PAUSE” BUTTON, press the “DELAY” button.
3. Set the “delay” time by pressing the “DELAY” timer button. Time will increase in increments of 1 hour with each press of the button.
4. Once the “DELAY” button is pressed the display will alternately show 1H and will also show the program the number selected within 2 seconds of the delay
time.
5. Close the door of your appliance and press the “START / PAUSE” button.
Note: If you open and close the door of the machine during the delay timer mode, or there has been a loss of electric power, the machine will continue
in delay timer mode until the timer has run out and will start the wash program as selected.
CANCELLING A DELAY TIME SET:
To cancel the delay timer function once set.
1. Press and hold the “DELAY” button for approximately 3 seconds.
2. After 3 seconds, the display will show “0h” confirming the cancellation of the delay timer program.
3. You can now select a new wash program as previously directed above.
Note: You cannot set a delay time mode once a wash program has begun.
END OF CYCLE
At the end of the wash cycle, “0” will be shown in the display. Open the door of the machine, press and hold the “START/PAUSE” button for approximately 3
seconds to turn the unit off.
OVERFLOW PROTECTION
Our Avanti dishwasher has an overfill protection device that could automatically shut off the inlet valve and start the drain pump if the water overflows. In the event
of an overflow, the system display will flash “F1” and will attempt to drain the water. If the overflow stops and the system drains the water the “F1” will disappear. If
the system cannot stop the overflow condition, turn off the main water supply before calling a service. If there is water in the base pan because of an overfill or
small leak, the water should be removed using a sponge before restarting the dishwasher.
WATER CUT OFF – WARNING
If during a wash cycle the water main is cut-off or turned off and the machine cannot take in water the display will flash “FF”. As long as the condition or lack of
water remains the display will continue to flash “FF”, once the water is returned to the unit, it will return to normal working mode.
LOSS OF ELECTRIC POWER – WARNING
If during a wash cyle the electricity is lost or turned off or the door of the machine has been opened, the machine cannot operate normally, the machine will return
to normal working mode after 8 seconds once the power has returned and if the internal temperature of the unit is above 113ºF.
DETERGENT DISPENSER
The dispenser must be refilled before the start of each wash cycle following the instructions provided in the “Wash Cycle Table”. Your dishwasher uses less
detergent and rinses aid than conventional dishwashers. Generally, only one teaspoon of detergent is needed for a normal wash load, heavily soiled items may
need more detergent. Always add the detergent just before starting the dishwasher, otherwise, it could become damp and not dissolve properly.
Amount of Detergent to Use
IF THE WATER IN YOUR AREA IS NOT TOO HARD, YOU MAY ALSO PREVENT THE FORMATION OF
Loading ...
Loading ...
Loading ...