User Manual Kwikset 400CV 15 SMT 6AL RCS 94002-862 Cove Keyed Entry Knob Featuring Smartkey Security In Satin Nickel

Documents for Kwikset 400CV 15 SMT 6AL RCS

The following documents are available:
User Manual Photos
400CV 15 SMT 6AL RCS photo

User Manual

For 400CV 15 SMT 6AL RCS.

23/8" (60 mm)
23/4" (70 mm)
Backset Distancia al centro
Centerline
Linea central
13/8" (35 mm)
13/4" (44 mm)
21/4" (57 mm)
Face of the door
Frente de la puerta
Edge of the door
Borde de la puerta
Fold
Doble
Note: Knobs will not be
installed until step 5.
Nota: Las perillas no se deben
instalar hasta el paso 5.
62821 / 01
Installation Guide
Guía de instalación
18003275625 • www.kwikset.com
If drilling a new door, use
the supplied template and
the complete door drilling
instructions available at
kwikset.com/doorprep
Si va a perforar una
puerta nueva, utilice la
plantilla suministrada y las
instrucciones completas para
la perforación de la puerta
en kwikset.com/doorprep
Parts in the box
Piezas en la caja
Required tools
Herramientas necesarias
*Call Kwikset to order
a service kit for 21/4"
(57 mm) thick doors.
*Llame a Kwikset para pedir
un kit de servicio para puertas
gruesas con un espesor
de entre 57 mm (21/4").
Latch
Pestillo
Strike
Placa
Screws
Tornillos
Keys
Llaves
Knobs
Perillas
SmartKey® tool
(SmartKey locks only)
Herramienta SmartKey
(las cerraduras de
SmartKey solamente)
Not required for all applications
No se requiere para todas
las aplicaciones
23/8" (60 mm)
or • o
23/4" (70 mm)
13/8"–21/4"*
35 mm–57 mm*
21/8"
54 mm
1"
25 mm
Hold the latch in front of the door hole, with
the latch face lush against the door edge.
Sostenga el pestillo en frente del oriicio
de la puerta, con la cara del pestillo
al ras con el borde de la puerta.
If the latch holes are centered in the door hole,
no adjustment is required. Proceed to step 4.
If the latch holes are NOT centered, adjust
latch. See “Latch Adjustment” (step 3C).
Si los oriicios del pestillo están centrados
con el oriicio de la puerta, no se
requiere ajustarlo. Vaya al paso 4.
Si los oriicios del pestillo NO esn
centrados, ajuste el pestillo. Consulte
“Ajuste del pestillo” (el paso 3C).
Latch Adjustment (only if needed)
Ajuste del pestillo (si es necesario)
Drilling Template
Plantilla de perforación
Move the pin to extend the latch.
Mueva el pasador para extender el pestillo.
Template is only needed if a new hole must be drilled in the door.
La plantilla solo se necesita en caso de que deba
perforarse un nuevo oriicio en la puerta.
A
Additional tools
(if needed)
Herramientas adicionales
(si es necesario)
wood block
bloque de madera
not centered
no centrado
centered
centrado
Instructions continue on reverse
Las instrucciones continúan en el reverso de la hoja
A
E
C D
G
J
H
F
B
A
A
B
C
Prepare door and check dimensions
Prepare la puerta y revise las dimensiones
1
Locate latch
Ubique el pestillo
2
Adjust the backset of the latch (if needed)
Ajuste la distancia al centro del pestillo (si es necesario)
3
Loading ...