BACH / ENCHANT
08/ 53622/4 (UK) Issue 2
OCN 11192
The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC) EN55014, EN60555-2
and EN60555-3. These cover the essential requirements of EEC Directives 2006/95/EC and 2004/108/EC
EN : This product is only suitable for well insulated rooms or occasional use. DE : Dieses Produkt ist nur für gut isolierte Bereiche oder gelegentliche
Verwendung geeignet. FR : Ce produit convient uniquement à des endroits bien isolés ou pour un usage occasionnel. IT : Questo prodotto è
adatto solo per spazi ben isolati o per uso occasionale. ES : Este producto sólo es adecuado para espacios bien aislados o un uso ocasional. NL :
Dit product is uitsluitend geschikt voor goed geïsoleerde ruimten of voor sporadisch gebruik. PL : Produkt ten jest odpowiedni wyłącznie do dobrze
odizolowanych miejsc lub do okazjonalnego użytku. NO : Dette produktet egner seg kun for godt isolerte rom eller sporadisk bruk. RO : Acest
produs este adecvat exclusiv spaţiilor bine ventilate sau utilizării ocazionale. CZ : Tento výrobek je vhodný pouze do dobře izolovaných prostor
nebo k příležitostnému použití. DK : Dette produkt er kun egnet til velisolerede rum eller lejlighedsvis brug. PT : Este produto somente é adequado
para espaços bem isolados ou uso ocasional. SE : Denna produkt är endast avsedd för välisolerade utrymmen eller tillfällig användning. FI : Tämä
tuote soveltuu ainoastaan hyvin eristettyihin tiloihin tai satunnaiseen käyttöön. SK : Tento výrobok je vhodný len pre dobre izolované priestory alebo
na občasné použitie. SI : Ta izdelek je primeren le za dobro izolirane prostore ali za občasno uporabo. HR : Ovaj proizvod je pogodan samo za
dobro izolirane prostore ili povremenu upotrebu. HU : Ez a termék csak jól szigetelt terekhez vagy eseti használatra alkalmas. SV : Denna produkt är
endast lämplig för användning i väl isolerade utrymmen eller enstaka användning.
1
4
A
B
C
D
E
A B C D E F
580 570 459 608 50 130
min
F
621
750
183
300 Min.
600 Recommended
160
160
200
1130 Recommended
3
2
600
696
183
300 Min.
600 Recommended
5
A
C
E
B
D
F
A B C
hair type of rugs.
If the supply cord is damaged it must be
replaced by the manufacturer or service
agent or similarly qualied person in order
to avoid a hazard.
CAUTION: In order to avoid a hazard due
to inadvertent resetting of the thermal cut-
out, this appliance must not be supplied
through an external switching device,
such as a timer, or connected to a circuit
that is regularly switched on and off by
the utility.
CAUTION - Some parts of this product
can become very hot and cause burns.
Particular attention has to be given where
children and vulnerable people are
present.
Technical Information
Model No: ASPIRE FSC E, ENCHANT E, BCH20E, BZT20E,
BACH-E
Heat Output 230V 240V
Nominal Heat Output P
Nom
1.7 - 1.9 kW
Minimum Heat Output P
min
0.9 - 1.0 kW
Maximum Continous Heat Output P
max,c
1.7 - 1.9 kW
Auxiliary Electricity Consumption
In Standby mode el
SB
0.41 - 0.44 W
with electronic room temperature control
General
Unpack the heater carefully and retain the packaging for
possible future use, in the event of moving or returning the
re to your supplier.
The re incorporates a ame effect, which can be used with
or without heating, so that the comforting effect may be
enjoyed at any time of the year. Using the ame effect on
its own only requires little electricity.
Before connecting the heater check that the supply voltage
is the same as that stated on the heater.
Please note: Used in an environment where background
noise is very low, it may be possible to hear a sound which
is related to the operation of the ame effect. This is normal
and should not be a cause for concern.
Electrical Connection
WARNING: THIS APPLIANCE MUST BE EARTHED
This heater must be used on an AC ~ supply only and the
voltage marked on the heater must correspond to the supply
voltage.
Before switching on, please read the safety warnings and
operating instructions.
Important Safety Advice
When using electrical appliances, basic
precautions should be followed to reduce
the risk of re, electric shock, and injury to
persons, including the following:
If the appliance is damaged, check
immediately with the supplier before
installation and operation.
Do not use this appliance in the immediate
surroundings of a bath, shower or swimming
pool.
Do not use outdoors.
This appliance must not be located
immediately above or below a fixed
socket outlet or connection box.
WARNING: The appliance carries
the Warning Symbol indicating that
it must not be covered or has a Do
not cover label. Do not cover or
obstruct in any way the heat outlet
grille located below the ame window
on the appliance Overheating will result
if the appliance is accidentally covered.
Do not place material or garments on the
appliance, or obstruct the air circulation
around the appliance, for instance by
curtains or furniture, as this could cause
overheating and a re risk.
In the event of a fault unplug the heater.
Unplug the appliance when not required
for long periods.The supply cord must be
placed on the right hand side of the heater
away from the heat outlet underneath the
appliance.
This appliance can be used by children
aged from 8 years and above and persons
with reduced physical, sensory or mental
capabilities or lack of experinence and
knowledge if they have been given
supervision or instruction concerning
use of the appliance in a safe way
and understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintaince shall not
be made by Children without supervision.
Children of less than 3 years should
be kept away unless continuously
supervised. Children aged from 3 years
and less than 8 years shall only switch
on/off the appliance provided that it has
been placed or installed in its intended
normal operating position and they have
been given supervision or instruction
concerning use of the appliance in a
safe way and understanding the hazards
involved. Children aged from 3 years and
less than 8 years shall not plug in, regulate
and clean the appliance or perform user
maintaince.
The appliance must be positioned so that
the plug is accessible.
Although this appliance complies with
safety standards, we do not recommend
its use on deep pile carpets or on long
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
EN
Controls: See Fig. 5
Icon Display Function Description
A
-
Power /
Standby
Press Once to turn the product ‘ON’.
Press a second time to put the product into ‘STANDBY’
(When returning from ‘STANDBY’ mode the product will return to previous settings unless
the product has been plugged out, in which case it will reset to factory settings)
B
Sleep
Timer
Press multiple times to change the ‘SLEEP TIMER’ in 0.5 hr increments from 0.5
hr to 8.0 hr before turning off. The remaining time on the ‘SLEEP TIMER’ displays.
(This icon is Green in Colour)
C
Flame Effect
‘FLAME EFFECT’ button cycles the unit sequentially through the 4 setting, LOW FLAME,
HIGH FLAME, DEMO MODE and OFF.
f1
Low
Flame
This setting will run the ame effect at a low brighness level. (The display will show F1)
f2
High
Flame
This setting will run the ame effect at a high brighness level. (The display will show F2)
fp
Demo
Mode
This setting will slowly pulse the ame effect between low and high brightness. (The display
will show FP)
-
Off
This will turn the ame effect off. If the heater is running, the display will activate and
remain active to read the set temperature and show if the product is on LOW HEAT/ HIGH
HEAT/COOL BLOW.
D
Heat
‘HEAT’ button cycles the unit sequentially through the 4 settings: LOW HEAT, HIGH HEAT,
COOL BLOW and OFF. The heat setting will be indicated by an icon in the oating display
see Fig.1.
When the ame effect is ‘ON’ the oating display will turn off after 5 seconds, however
if the heater is being used independantly of the ame effect. The low heat or high heat
icon will appear continuously in the oating display.
Low
Heat
This setting will run the heater at ‘LOW HEAT’ this setting will be indicated by the ‘LOW
HEAT’ icon and the letters ‘LO’ appearing in the display.
(This icon is Orange in Colour)
High
Heat
This icon in the oating display indicates ‘HIGH HEAT’ this setting will be indicated by the
‘HIGH HEAT’ icon and the letters ‘HI’ appearing in the display.
(This icon is Red in Colour)
Cool
Blow
This icon in the oating display indicates ‘COOL BLOW’ this setting will be indicated by
the ‘COOL BLOW’ icon and the letters ‘CB’ appearing in the display.
(This icon is Blue in Colour)
- Off
This switches the heater and blower ‘OFF’, no icon will be displayed in the oating display.
Note the blower will run for 10-20 seconds after being turned off this is to ensure the product
cools down safely.
E
-
Temp
Down
Press multiple times to lower the heater temperature in 1
0
C increments. The lowest
temperature that can be set 5
0
C.
Note: Once you stop at your desired temperature this will flash 3 times, then the display
will show the room temperature as detected by the product. If the set temperature is
lower than the detected room temperature the heater will not activate.
F
-
Temp
Up
Press multiple times to increase the heater temperature in 1
0
C increments. The highest
temperature that can be set 37
0
C.
Note: Once you stop at your desired temperature this will flash 3 times, then the display
will show the room temperature as detected by the product. If the set temperature is
lower than the detected room temperature the heater will not activate.
User Modes:
Mode Name /Discription Action (Actions cannot be input by remote control)
Change Celsius (
0
C) to Fahrenheit (
0
F)
Press both 3 Dot Button (
) and 2 Dot ( ) on the unit and hold until beep is heard
and display flashes. (To revert back to Celsius repeat this action)
Disable/Enable Heat Options
Hold both 1 Dot Button (
) and Flame Button ( ), on the unit, for 2 seconds, when
the heater has been disabled the display will read “--” and beep. To enble heat repeat
this action.
3. Using timber studs to support the re, devise and construct
a suitable means of supporting the product within the wall
partition and provide electrical power for the re to be
HARD wired. For recommended sizes of height, width and
depth of opening for recess and hole xing dimensions
for each model - see Fig. 3.
4. Remove the front/trim by following the steps as outlined
previously.
5. Locate the 4 xing holes, position the re accordingly, and
rmly x using the appropriate screws.
6. Replace the front/trim.
NOTE: The appliance should be HARD wired to an electrical
power outlet when placed in a recessed installation.
Please consult a qualied electrician for appropriate wiring
requirements.
Trim colour options – see Fig. 4
NOTE: Trim Colour Options only availible on Bizet & Aspire.
The re comes with a reversible inner trim. To reverse the trim
rst remove the front cover as per Fig.3, gripping the front
panel on either side, gently pull the bottom of the panel
forward while lightly lifting upward, the front panel should
lift away.
This will allow access to the reversible trim, once again
gripping the trim on either side gently pull the bottom of the
trim forward while lightly lifting upward, the reversible trim
will lift away.
Now carefully replace the panels in the reverse of above.
Thermal Safety Cut-out
The built-in overheat cut-out, switches off the appliance
automatically in the event of a fault! Should this occur
switch off the appliance or disconnect the mains plug from
the socket.
Remove any obstructions which may have caused the
overheating. After a short cooling down phase, the
appliance is ready for use again! If the fault should occur
again, contact your local dealer!
WARNING: In order to avoid a hazard due to inadvertent
resetting of the thermal cut-out, this appliance must not be
supplied through an external switching device, such as a
timer, or connected to a circuit that is regularly switched on
and off by the utility.
Maintenance
WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY
BEFORE ATTEMPTING ANY MAINTENANCE.
Light Emitting Diode
This re is tted with LED (Light Emitting Diode) lamps. These
LED lamps are maintenance-free and should not require
replacing during the life of the product.
Cleaning
WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY
BEFORE CLEANING THE HEATER.
For general cleaning use a soft clean duster – never use
abrasive cleaners. The glass viewing screen should be
cleaned carefully with a soft cloth.
DO NOT use proprietary glass cleaners.
To remove any accumulation of dust or uff the soft brush
attachment of a vacuum cleaner should occasionally be
used to clean the outlet grille of the fan heater.
WARNING: do not operate the product without the grille
and outer glass in position as this may effect the operation
of the heater.
Remote Control - See Fig. 6
The maximum range of use is ~ 5metres.
NOTE: It takes time for the receiver to respond to the
transmitter.
NOTE: The reciever for the remote control is located in
the display, aim the remote control in this direction when
inputting commands.
Do not press the buttons more than once within two seconds
for correct operation.
Battery Information - See Fig. 6
1. To activate the remote control remove the clear battery
isolation strip at the base of the remote control, which is used
to ensure your remote control reaches you fully charged.
2. To replace the remote control battery, turn over the
remote control, and follow the diagram embossed on the
remote control
3. Only use CR2025 or CR2032 size of batteries.
Wall xing - see Fig. 2, 3 & 4
The appliance should be securely xed to the wall using the
wall plugs and screws supplied for block walls.
Note – for studded walls special fasteners are required, see
diagram for recommended position of xing screws.
Recessed Installation
Please note that this appliance can also be wall-mounted
so that it is recessed. This can be installed in a large replace
opening or a purpose built wall. See Fig. 3 for size of recess
required and hole xing dimensions. This replace insert does
NOT require venting.
In order to ensure it’s future safety in use, it is essential that
this re is securely xed to the wall.
IT IS IMPORTANT THAT THE FIXING DEVICE CHOSEN IS
APPROPRIATE TO THE WALL MATERIAL TO WHICH THE FIRE IS
BEING FIXED. SOME MODERN INTERNAL BUILDING MATERIALS
ARE VERY LOW DENSITY BLOCK AND REQUIRE SPECIALIZED
FIXING DEVICES TO PROVIDE A SAFE,SECURE INSTALLATION.
The installation of this fire should be carried out by a
competent person. If in doubt please consult your local
builder.
This section provides step by step instructions for selecting a
location and preparing the site to install the replace into
the following:
Existing Fireplace
1. Make sure that the re is located on a at surface.
2. Seal all draughts and vents to prevent chimney debris
from falling onto the Fireplace Insert. Do not install into
an existing replace that is prone to dampness.
3. Remove the front/trim by following the steps as outlined
in Fig. 4
4. Locate the 4 xing holes, position the re accordingly, and
rmly x the appliance to the wall using the appropriate
screws.
5. Replace the front/trim.
New Support Structure Construction
When planning where to position your purpose built support
structure the following steps must be observed:
1. Place the re in the desired location to see how it will look
in the room.
2. Mark the desired location for the new support structure
in the room and store the re in a safe, dry and dust free
location.
Recycling
For electrical products sold within the European
Community. At the end of the electrical
products useful life it should not be disposed
of with household waste. Please recycle where
facilities exist. Check with your Local Authority
or retailer for recycling advice in your country.
After Sales Service
Should you require after sales service or should you need
to purchase any spares, please contact the retailer from
whom the appliance was purchased or contact the service
number relevant to your country on the warranty card.
Please do not return a faulty product to us in the rst instance
as this may result in loss or damage and delay in providing
you with a satisfactory service. Please retain your receipt
as proof of purchase.
