Loading ...
Loading ...
Loading ...
Alert Reason Solution
Lock button lashes
red once with one
beep*.
One incorrect code
entered.
Re-enter code.
Lock button lashes
red three times with
three beeps*.
No user code
programmed.
Program at least one
user code.
Programming timeout
after ive seconds.
Attempt programming
procedure again.
Unsuccessful
programming.
Lock button lashes
red 15 times with 15
beeps*
Three incorrect codes
entered within one
minute.
Re-enter code after
60 second keypad
lockout.
Lock button lashes
red with fast beeping
sound for three to four
seconds.
Low battery. Replace batteries.
Lock button lashes
green with continuous
beeping sound for two
seconds.
Door jammed while
attempting to lock.
Manually re-lock door.
If needed, reposition
strike.
Factory Reset
A factory reset will delete all codes associated with the lock, and it will
remove it from your smart home system.
Manual Door Handing
If needed, the door handing process can be initiated manually.
This is useful if the lock is being moved to a di erent door.
1. Remove battery pack.
Status
LED
2. Press and HOLD the Program
button while reinserting the
battery pack.
Release button once battery
pack is installed. The status
LED will lash red and green.
3. Press the
Program
button once
more.
4. The latch bolt will extend
and retract to learn the
orientation of the door.
The Status LED will indicate
success or failure.
Success: LED lashes green
Failure: LED remains solid red
If the Status LED indicates a failure,
see the online Programming
and Troubleshooting Guide
or call Technical Support.
© 2017 Spectrum Brands, Inc.
1. Read all instructions in their entirety.
2. Familiarize yourself with all warning and caution statements.
3. Remind all family members of safety precautions.
4. Protect your user codes and mastercode.
5. Dispose of used batteries according to local laws and regulations.
CAUTION: Prevent unauthorized entry. Since anyone with access to the back panel can
change the user codes, you must restrict access to the back panel and routinely check the
user codes to ensure they have not been altered without your knowledge. The use of a
mastercode can help protect your system’s settings.
WARNING: This Manufacturer advises that no lock can provide complete security by itself.
This lock may be defeated by forcible or technical means, or evaded by entry elsewhere
on the property. No lock can substitute for caution, awareness of your environment, and
common sense. Builder’s hardware is available in multiple performance grades to suit the
application. In order to enhance security and reduce risk, you should consult a qualiied
locksmith or other security professional.
Important Safeguards
If unsuccessful: Make sure to enter the same valid code in steps 3 and 5.
Test code: While the door is open, test the user code
to make sure it no longer unlocks the door.
If no button is pressed for ive seconds, the system will time
out, and you will need to restart the procedure.
Network Information
ZWave® System Notes
This product is a security enabled ZWave Plus product and must be used with a Security
Enabled ZWave controller to be fully utilized. ZWave is a “Wireless mesh network,” and
results may vary based on building construction and communication path.
To assure interoperability, each ZWave product must pass a stringent conformance test to
assure that it meets the ZWave standard for complete compliance with all other devices and
controls. The ZWave identity mark assures consumers, integrators, dealers and manufacturers
that their products will reliably perform with any other ZWave device. And, regardless of the
vendor, always powered nodes may act as a repeater for Kwikset/Weiser/Baldwin products.
ZWave Coniguration and Association Parameters are available on
the SmartCode 888 page at www.kwikset.com.
Removing the lock from the network
Follow your smart home system’s instructions
to remove the lock from the network. When
prompted by the system, press button A” on
the lock interior once.
4 / 4
SmartCode 888 at a Glance
1. Press Program button once. 2. Press button “A” once. 1. Press Program button once. 2. Press button “A” once.
1. Press Program button once. 2. Press button “A” once.
Reference Guide
Status LED
The Status LED blinks every 6
seconds to communicate whether
the door is locked or unlocked.
This feature is on by default.
Blinking Green: Unlocked
Blinking Amber: Locked
Blinking Red: Low battery
Solid Red: Unsuccessful door handing
process. See online Programming
and Troubleshooting Guide.
Auto-Lock
Auto-lock automatically re-locks the door after unlocking. This feature is set to 30 seconds and is turned o by default.
Turn Auto-Lock On/O Change Auto-Lock Time Delay
Troub leshooting
Mute/Unmute Audio
Audio is on by default.
Deleting a single user code
Note: All codes may be deleted at once if the mastercode
is enabled. For more information about the mastercode,
consult the Programming and Troubleshooting Guide.
Status
LED
System Alerts
Exterior
Keypad
Lock
button
Keyway
SmartKey
tool hole
Back
panel
Program
button
Status
LED
Turnpiece
shaft
Note: When the cover is
removed, the turnpiece shaft
can be used to manually
lock and unlock the door.
Interior (cover removed)
Button “A”
A complete Programming and Troubleshooting Guide is
available on the SmartCode 888 page at www.kwikset.com.
3. Press button “34” multiple
times if needed to reach
desired state.
Green Lock Button:
Feature is enabled.
Red Lock Button:
Feature is disabled.
4. Press Lock button once. 3. Press button
“90” once.
4. Press button once
that corresponds
to desired
time delay:
“12” – 30 sec.
“34” – 60 sec.
“56” – 90 sec.
“78” – 120 sec.
“90” – 180 sec.
5. Press Lock
button once.
1. Press Program button once. 2. Press button “A” once.
Turn Status LED On/O
3. Press button “12” multiple
times if needed to reach
desired state.
Green Lock Button:
Feature is enabled.
Red Lock Button:
Feature is disabled.
4. Press Lock button once.
3. Press button “56” multiple times if
needed to reach desired state.
Green Lock Button:
Feature is enabled.
Red Lock Button:
Feature is disabled.
4. Press Lock button once.
1. Press Program button once. 2. Press Lock button once.
3. Enter user code to be deleted. 4. Press Lock button once.
5. Re-enter user code. 6. Press Lock button once.
1. Remove battery pack.
Status
LED
2. Press and HOLD the Program
button while reinserting the
battery pack.
Keep holding the button
for 30 seconds until
the lock beeps and the
status LED lashes red.
3. Press the Program button
once more. When the LED
lashes green and you hear
one beep, the lock has been
reset.
4. After a few seconds, the lock will initiate the door
handing process, and the latch bolt will extend
and retract to learn the orientation of the door.