EN Operator’s manual
Electric Lawnmower
EasiStore 300R Art. 9679873-01
EasiStore 340R Art. 9679874-01
EasiStore 380R Art. 9679875-01
®
EN
1. SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
4. MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
5. STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
6. TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
7. TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
8. ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
9. SERVICE / WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Original instructions.
This product is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the product by a person
responsible for their safety. Children should be supervised to ensure
that they do not play with the product. The use of this product by young
people under the age of 16 is not recommended.
Intended use:
The FLYMO Lawnmower is intended to mow lawn in private domestic
gardens and allotments.
The product is not intended for long term use.
DANGER! Risk of injury!
Do not use the product to cut bushes, hedges, shrubs, to cut of
climbers or grass on roofs or balcony boxes, to chop up branches,
twigs and to level irregularities in the soil. Do not use the product
on a slope steeper than 20° maximum.
Voltage Cable length Cross section
220 – 240 V / 50 Hz Up to 20 m 1.5 mm
2
220 – 240 V / 50 Hz 20 – 50 m 2.5 mm
2
1. Mains cables and extensions are available from your local Approved Service
Centre.
2. Only use extension cables specifically designed for outdoor use and
which conform to one of the following specifications:
Ordinary rubber (60245 IEC 53), Ordinary PVC (60227 IEC 53) or
Ordinary PCP (60245 IEC 57).
3. If the connection lead is damaged, it must be replaced by the manufacturer,
its service agent or similarly qualified persons in order to avoid a hazard.
Training
a) Read the instructions carefully. Be familiar with the controls and the correct
use of the machine.
b) Never allow children or people unfamiliar with these instructions to use the
machine. Local regulations can restrict the age of the operator.
c) Never operate the machine while people, especially children, or pets are
nearby.
d) Keep in mind that the operator or user is responsible for accidents or hazards
occurring to other people or their property.
Preparation
a) While operating the machine always wear substantial footwear and long
trousers. Do not operate the machine when barefoot or wearing open san-
dals. Avoid wearing clothing that is loose fitting or that hanging cords or ties.
b) Thoroughly inspect the area where the machine is to be used and remove all
objects which can be thrown by the machine.
c) Before using, always visually inspect to see that the blade, blade bolt and the
blade assembly are not worn or damaged. Replace worn or damaged com-
ponents in set to preserve balance. Replace damaged or unreadable labels.
d) Before use check the supply and extension cord for signs of damage or
aging. If the cord becomes damaged during use, disconnect the cord from
the supply immediately.
DO NOT TOUCH THE CORD BEFORE DISCONNECTING THE SUPPLY.
Do not use the machine if the cord is damaged or worn.
Operation
a) Operate the machine only in daylight or in good artificial light.
b) Avoid operating the machine in wet grass.
c) Always be sure of your footing on slopes.
d) Walk, never run.
e) Mow across the face of slopes, never up and down.
f) Exercise extreme caution when changing direction on slopes.
g) Do not mow excessively steep slopes.
h) Use extreme caution when reversing or pulling the machine towards you.
i) Stop the blade(s) if the machine has to be tilted for transportation when cross-
ing surfaces other than grass, and when transporting the machine to and from
area to be used.
j) Never operate the machine with defective guards or shields, or without safety
devices, for example deflectors and / or grass collector, in place.
k) Switch on the motor carefully according to instructions and with feet well
away from the blade(s).
l) Do not tilt the machine when switching on the motor, except if the machine
has to be tilted for starting. In this case, do not tilt it more than absolutely
necessary and lift only the part, which is away from the operator.
m) Do not start the machine when standing in front of the discharge opening.
n) Do not put hands or feet near or under rotating parts. Keep clear of the
discharge opening at all times.
o) Do not transport the machine while the power source is running.
p
1
) Stop the machine, and remove plug from the socket. Make sure that all
moving parts have come to a complete stop:
– whenever you leave the machine,
– before clearing blockages or unclogging chute,
– before checking, cleaning or working on the machine,
– after striking a foreign object. Inspect the machine for damage and make
repairs before restarting and operating the machine;
if the machine starts to vibrate abnormally (check immediately)
– inspect for damage,
– replace or repair any damaged parts,
– check for and tighten any loose parts.
Maintenance and storage
a) Keep all nuts, bolts, and screws tight to be sure the machine is in safe
working condition.
b) Check the grass collector frequently for wear or deterioration.
c) Replace worn or damaged parts for safety.
d) On machines with multi blade, take care as rotating one blade can cause
other blades rotate.
e) Be careful during adjustment of the machine to prevent entrapment of the
fingers between moving blades and fixed parts of the machine.
IMPORTANT!
Read the operator’s manual carefully before use and keep for future
reference.
Symbols on the product:
Read operator’s manual.
Keep bystanders away.
Beware of sharp blades. Blades continue to rotate
after the motor is switched off.
Remove plug from mains before maintenance.
Not valid for the electric mower.
Secure the working area before starting to work.
Watch out for hidden cables.
General safety warnings
Electrical safety
DANGER! Electric shock!
Risk of injury due to electric shock.
v The product must be supplied through a residual current device (RCD)
having a rated residual operating current not exceeding 30 mA.
DANGER! Risk of physical injury!
Cut injury when the blade turns or the product starts
accidentally.
v Disconnect the product from the mains before you maintain or
replace parts. Thereby the disconnected socket must be in the
visual range.
Cables
If extension cables are used, these must comply with the minimum cross-
sections in the table below:
1. SAFETY
4
2. ASSEMBLY
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Disconnect the product from the mains and use gloves before
you assemble the product.
To assemble the handle [ Fig. A1 / A2 / A3 /A4 ]:
1. Put the springs on the shafts.
2. Put the handle plates on the shafts.
3. Put the lower handle on the shafts.
4. Put the washers on the shafts.
5. Insert the bolts into the quick-release levers.
6. Screw the quick-release levers loosely onto the shafts and clamp
them down.
7. Put the upper handle on the lower handles and slide the screws
through the boreholes (there are 2 holes in the lower handle to
choose the desired height).
8. Put the washers on the screws.
9. Screw the locking nuts onto the screws.
10. Attach the control cable with the cable clips.
To assemble the grass box [ Fig. A5 / A6 / A7 / A8 / A9 ]:
1. Push the grass box handle into the slots in the grass box cover until it
audibly engages.
2. Slide the grass box tongue into the slots in the grass box until it audibly
engages.
3. Align the grass box cover and the grass box locators.
4. Fold the grass box cover towards the grass box.
5. Push the grass box cover on the grass box. Make sure that all clips are
snapped in correctly.
To attach the grass box to the lawnmower [ Fig. A10 ]:
1. Lift the protective cover.
2. Attach the grass box to the hooks on the rear of the mower.
f) Always allow the machine to cool down before storing.
g) When servicing the blades be aware that, even though the power source is
switched off, the blades can still be moved.
h) Use only genuine replacement parts and accessories.
Additional safety warnings
Electrical safety
DANGER! Cardiac arrest!
This product makes an electromagnetic field while it operates. This
field may under some conditions interfere with active or passive medical
implants. To decrease the risk of conditions that can possibly injure or
kill, we recommend persons with medical implants to speak with their
physician and the medical implant manufacturer before you operate the
product.
Do not use under wet conditions.
Do not operate in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust.
Personal safety
DANGER! Risk of suffocation!
Small parts can be easily swallowed. There is also a risk that the polybag
can suffocate toddlers. Keep toddlers away when you assemble the
product.
Do not use the start levers alternately.
Do not disassemble the product further than the delivery status.
Use gloves, wear slip resistant shoes and wear eye protection.
Do not overload the mower.
Never operate the product when you are tired, ill or under the influence of alcohol,
drugs, or medicine.
Danger of slipping:
– in wet grass
– on steep slopes
– during transport
Be careful while going backwards.
3. OPERATION
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Wait for the blade to stop, disconnect the product from
the mains and use gloves before you adjust or transport
the product.
To adjust the cutting height:
For the first cut of the season, always cut on the highest cutting height
possible, and gradually lower the cutting height over successive cuts to
your desired height for the lawn.
Only for 300R (in 3 positions) [ Fig. O1 / O2 / O3 / O4 / O5 ]:
The cutting height can be adjusted from 20 – 60 mm.
Position ‘Low’ (20 mm): Cutting height setting should only be used on
well maintained ‘manicured lawns’ without excessive moss or thatch.
Position ‘Mid’ (40 mm): Cutting height setting is the suitable for most
lawns.
Position ‘High’ (60 mm): Cutting height setting is used when you lawn
has excessive growth such as following holidays or first cut of the season.
v Move both axles to the desired position in the E-Gate. Make sure that
both sides of the axle are in the same position. Make sure that both
axles are in the same position.
Only for 340R / 380R (in 5 positions) [ Fig. O6 ]:
The cutting height can be adjusted from 20 – 60 mm (from rear to front).
Position 1 (20mm): Cutting height setting should only be used on well
maintained ‘manicured lawns’ without excessive moss or thatch.
Position 2 (30 mm): Cutting height setting is the suitable for most lawns.
Position 3 (40 mm): Cutting height setting is the suitable for most lawns.
Position 4 (50 mm): Cutting height setting is the suitable for most lawns.
Position 5 (60 mm): Cutting height setting is used when you lawn has
excessive growth such as following holidays or first cut of the season.
1. Pull the lever to the wheel.
2. Move the lever to the desired position.
3. Release the lever and let it engage.
To start the mower [ Fig. O7 ]:
DANGER! Risk of injury!
Risk of injury if the product does not stop when you
release the start lever.
v Do not bypass the safety devices or switches. For example
do not attach the start lever to the handle.
To start:
The mower is fitted with a two-handed safety device (start lever
with starting lockout) to prevent the mower from being turned on
by accident.
There are two start levers. Either one has to be used to start.
1. Connect the mains cable to the mains.
2. Push the starting lockout with one hand and pull the start lever with the
other hand.
The mower starts.
3. Release the starting lockout.
Only for 340R / 380R [ Fig. O8 ]: The level indicator opens during
mowing. When it closes during mowing, the grass box is full and
must be emptied.
To stop:
v Release the start lever.
The mower stops.
Tips to use the mower:
If grass residue is left in the discharge opening, pull the mower backwards
about 1 m so that the grass residue can drop out downwards.
To produce a well-maintained lawn and optimise the cutting performance,
we recommend to cut the lawn regularly once a week if possible. The lawn
becomes denser if you cut it frequently.
After relatively long cutting intervals (holiday lawn), first of all cut in one
direction with the highest cutting height and then cut in the crosswise
direction with the required cutting height.
5
IMPORTANT!
v Dispose of the product through or via your municipal recycling
collection centre.
6. TROUBLESHOOTING
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Wait for the blade to stop, disconnect the product from the
mains and use gloves before you troubleshoot the product.
To replace the blade [ Fig. T1 ]:
DANGER! Risk of injury!
Cut injury when the blade turns and it is damaged,
bent, out of balance or has chipped edges.
v Do not use the mower when the blade is damaged, bent,
out of balance or has chipped edges.
v Do not regrind the blade.
The FLYMO spare parts are available from your FLYMO dealer or from the
FLYMO service.
Only use an original FLYMO blade:
• FLYMO replacement blade for 300R: Art. FLY 085
• FLYMO replacement blade for 340R: Art. FLY 086
• FLYMO replacement blade for 380R: Art. FLY 088
1. Unscrew the blade bolt.
2. Remove the blade bolt and the washer.
3. Remove the blade and the spacer.
4. Put the spacer and the new blade on the mower.
5. Put the washer on the blade bolt.
6. Screw the new blade tight with the blade bolt
(tightening torque is 15 – 20 Nm).
Problem Possible Cause Remedy
Mower does not start Mains cable is disconnected
or damaged.
v Connect the mains cable or
if necessary let it be replaced
by an authorised specialist
dealer or the FLYMO Service.
Motor is blocked. v Remove the obstacle.
Start again.
Engine is jammed and
makes a noise
Motor is blocked. v Remove the obstacle.
Start again.
Cutting height is too low. v Raise the cutting height.
Loud noises, the mower
is rattling
Screws on engine, its fixing
or on the mower chasing are
loose.
v Let the screws be tightened
by an authorised specialist
dealer or the FLYMO Service.
Mower runs unevenly or
vibrates strongly
Blade is damaged / worn or the
blade mounting is released.
v Replace the blade.
Blade is very dirty. v Clean the blade.
Lawn is not cleanly mowed Blade is blunt or damaged. v Replace the blade.
Cutting height is too low. v Raise the cutting height.
NOTE: For any other malfunctions please contact the FLYMO Customer Service.
Repairs must only be done by FLYMO service departments or specialist dealers
approved by FLYMO.
7. TECHNICAL DATA
Electric Lawnmower
Unit Value
EasiStore 300R
Value
EasiStore 340R
Value
EasiStore 380R
Rated power W 1200 1400 1600
Mains voltage V (AC) 230 230 230
Mains frequency Hz 50 50 50
Speed of rotation cutting
blade
R/min 3700 3350 3500
Cutting width cm 30 34 38
If possible, only cut the grass when it is dry, if the grass is damp,
the cutting pattern will be uneven.
Rear Roller:
For lawnmowers fitted with a rear roller, it is possible to create a striped
effect on the lawn. For the best stripe results, we recommend cutting on
the lowest possible cutting height suited to your lawn. The stripe effect
will fade in time between cuts.
Transport position [ Fig. O9 ]:
The easy transport position provides additional mobility due to its upright
driving position. Easy to get on and off the lawn at any distance.
1. Attach the grass box to the switch box (see 5. STORAGE).
2. Pull the mower to and from the lawn when it is set in the storage
position.
4. MAINTENANCE
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Wait for the blade to stop, disconnect the product from the
mains and use gloves before you maintain the product.
To clean the mower:
DANGER! Risk of injury!
Risk of injury and risk of damage to the product.
v Do not clean the product with water or with a water jet
(in particular high-pressure water jet).
v Do not clean with chemicals including petrol or solvents.
Some can destroy critical plastic parts.
The airflow slots must always be clean.
To clean the underside of the mower:
The underside is easiest to clean after you mowed.
1. Lay the mower on its side carefully.
2. Clean the underside, the blade and the discharge opening
with abrush (do not use sharp objects).
To clean the overside of the mower and the grass box:
1. Clean the overside with a damp cloth.
2. Clean the airflow slots and the grass box with a soft brush
(do not use sharp objects).
5. STORAGE
To put into storage [ Fig. S1 ]:
The product must be stored away from children.
1. Disconnect the mower from the mains.
2. Clean the mower (see 4. MAINTENANCE).
3. The cable hooks must both be on the upper handle.
Wrap the cable in a figure of 8.
4. Store the mower in a dry, enclosed and frost-free place.
Easi Storage position [ Fig. S2 ]:
1. Remove the grass box.
2. Set on the highest cutting height.
3. Fold the handle flat and lock it in position 4.
4. Stand the mower upright.
5. Make sure that the grass box is completely empty.
6. Attach the grass box to the switch box with the storage hook.
Make sure that the grass box is completely secured, the storage
function is accomplished.
7. Store the mower in upright position.
Disposal:
(in accordance with RL2012/19/EC)
The product must not be disposed of to normal household
waste. It must be disposed of in line with local environmental
regulations.
6
Electric Lawnmower
Unit Value
EasiStore 300R
Value
EasiStore 340R
Value
EasiStore 380R
Cutting height adjustment mm
20 – 60
(3 positions)
20 – 60
(5 positions)
20 – 60
(5 positions)
Volume of grass box l 30 35 45
Weight kg 9.0 11.0 12.6
Sound pressure level L
pA
1)
Uncertainty k
pA
dB (A)
88
3
88
3
89
3
Sound power level L
WA
2)
:
measured / guaranteed
Uncertainty k
WA
dB (A)
92 / 95
2.52
92 / 93
1.86
93 / 95
1.89
Hand / arm vibration a
vhw
1)
m/s
2
< 2.5 < 2.5 < 2.5
Measuring process complying with:
1)
EN 60335-2-77
2)
RL 2000/14/EC
NOTE: The stated vibration emission value has been measured according to
astandardized test procedure and can be used for comparison of one electric
power tool with another. It can also be used for preliminary evaluation of expo-
sure. The vibration emission value can vary during actual use of the electric power tool.
8. ACCESSORIES
FLYMO Replacement Blade
for 300R
As replacement for blunt blade. Art. FLY 085
FLYMO Replacement Blade
for 340R
As replacement for blunt blade. Art. FLY 086
FLYMO Replacement Blade
for 380R
As replacement for blunt blade. Art. FLY 088
9. SERVICE / WARRANTY
Service:
Please contact the address on the back page.
Warranty statement:
In the event of a warranty claim, no charge is levied to you for the
services provided.
Husqvarna UK Ltd. grants a warranty for all original FLYMO new products
for two years from the date of original purchasefrom the retailer, provided
that the devices have been for private use only. This manufacturer’s war-
ranty does not apply to products acquired second hand. This warranty
includes all significant defects of the product that can be proved to be
material or manufacturing faults. This war ranty is fulfilled by supplying
afully functional replacement productor by repairing the faulty product
sent to us free of charge; we reserve the right to choose between these
options. This service is subject to the following provisions:
• The product has been used for its intended purpose as per the
recommendations in the operating instructions.
• Neither the purchaser nor a third party has attempted to open or
repair the product.
• Only Original FLYMO replacement parts and wear parts have been
used for operation.
• Presentation of the receipt.
Normal wear and tear of parts and components (such as blades, blade
fixing parts, turbines, light bulbs, V-belts / toothed belts, impellers, air
filters, spark plugs), visual changes, wear parts and consumables are
excluded from the warranty.
This manufacturer’s warranty is limited to replacement and repair of
products in accordance with the abovementioned conditions. The manu-
facturer’s warranty does not constitute an entitlement to lodge other
claims against us as a manufacturer, such as for damages. This manu-
facturer’s warranty does not, of course, affect statutory and contractual
warranty claims against the dealer / retailer.
The manufacturer’s warranty is governed by the law of the Federal
Republic of Germany.
In case of a warranty claim, please return the faulty product, together with
a copy of the receipt and a description of the fault, with postage paid to
the service address.
Consumables:
The blade and the wheels are consumables and are not included in the
warranty.
7
8
In accordance with the German Product Liability Act, we hereby expressly declare that we accept no liability for damage incurred from our products
where said products have not been properly repaired by a FLYMO-approved service partner or where original FLYMO parts or parts authorised by
FLYMO were not used.
PRODUCT LIABILITY
The undersigned hereby certifies as the authorized representative of the manufacturer, Husqvarna AB, 561 82 Huskvarna, Sweden, that, when leaving
our factory, the unit(s) indicated below is / are in accordance with the harmonised EU guidelines, EU standards of safety and product specific standards.
This certificate becomes void if the unit(s) is / are modified without our approval.
EC DECLARATION OF CONFORMITY
Description of the product: Electric Lawnmower
Product type EasiStore 300R
EasiStore 340R
EasiStore 380R
Article-Number 9679873-01
9679874-01
9679875-01
CE-Directives 2006/42/EC
2014/30/ EU
2000/14/EC
2011/65/ EU
Harmonised EN EN ISO 12100
EN 60335-1
EN 60335-2-77
Deposited Documentation GARDENA Technical Documentation,
M. Kugler, 89079 Ulm
Conformity Assessment according to 2000/14/EC Procedure: art. 14 Annex VI
Noise level: measured / guaranteed EasiStore 300R: 92 dB(A) / 95 dB(A)
EasiStore 340R: 92 dB(A) / 93 dB(A)
EasiStore 380R: 93 dB(A) / 95 dB(A)
Year of CE marking: 2019
Ulm, 13.12.2019
Authorised representative:
John Thompson
Product and Marketing Director EUAP
10
Deutschland / Germany
GARDENA Manufacturing GmbH
Central Service
Hans-Lorenser-Straße 40
D-89079 Ulm
Produktfragen:
(+49) 731 490-123
Reparaturen:
(+49) 731 490-290
Albania
COBALT Sh.p.k.
Rr. Siri Kodra
1000 Tirana
Argentina
Husqvarna Argentina S.A.
Av.del Libertador 5954 –
Piso 11 – Torre B
(C1428ARP) Buenos Aires
Phone: (+54) 11 5194 5000
info.gardena@ar.husqvarna.com
Armenia
Garden Land Ltd.
61 Tigran Mets
0005 Yerevan
Australia
Husqvarna Australia Pty. Ltd.
Locked Bag 5
Central Coast BC
NSW 2252
Phone: (+ 61) (0) 2 4352 7400
customer.service@
husqvarna.com.au
Austria / Österreich
Husqvarna Austria GmbH
Industriezeile 36
4010 Linz
Tel. : (+43) 732 77 01 01-485
service.gardena@
husqvarnagroup.com
Azerbaijan
Firm Progress
a. Aliyev Str. 26A
1052 Baku
Belgium
Husqvarna België nv/sa
Gardena Division
Rue Egide Van Ophem 111
1180 Uccle / Ukkel
Tel.: (+32) 2 720 92 12
Mail: info@gardena.be
Bosnia / Herzegovina
SILK TRADE d.o.o.
Industrijska zona Bukva bb
74260 Tešanj
Brazil
Husqvarna do Brasil Ltda
Av. Francisco Matarazzo,
1400 – 19
o
andar
São Paulo – SP
CEP: 05001-903
Tel: 0800-112252
marketing.br.husqvarna@
husqvarna.com.br
Bulgaria
AGROLAND България АД
бул. 8 Декември, № 13
Офис 5
1700 Студентски град
София
Тел.: (+359) 24 66 6910
Canada / USA
GARDENA Canada Ltd.
100 Summerlea Road
Brampton, Ontario L6T 4X3
Phone: (+1) 905 792 93 30
Chile
Maquinarias Agroforestales
Ltda. (Maga Ltda.)
Santiago, Chile
Avda. Chesterton
# 8355 comuna Las Condes
Phone: (+56) 2 202 4417
Dalton@maga.cl
Zipcode: 7560330
China
Husqvarna (China) Machinery
Manufacturing Co., Ltd.
No. 1355, Jia Xin Rd.,
Ma Lu Zhen, Jia Ding Dist.,
Shanghai
201801
Phone: (+86) 21 59159629
Domestic Sales
www.gardena.com.cn
Colombia
Husqvarna Colombia S.A.
Calle 18 No. 68 D-31, zona
Industrial de Montevideo
Bogotá, Cundinamarca
Tel. 571 2922700 ext. 105
jairo.salazar@husqvarna.com.co
Costa Rica
Compania Exim
Euroiberoamericana S.A.
Los Colegios, Moravia,
200 metros al Sur del Colegio
Saint Francis – San José
Phone: (+506) 297 68 83
exim_euro@racsa.co.cr
Croatia
SILK ADRIA d.o.o.
Josipa Lončara 3
10090 Zagreb
Phone: (+385) 1 3794 580
silk.adria@zg.t-com.hr
Cyprus
Med Marketing
17 Digeni Akrita Ave
P.O. Box 27017
1641 Nicosia
Czech Republic
Husqvarna Česko s.r.o.
Türkova 2319/5b
149 00 Praha 4 – Chodov
Bezplatná infolinka :
800 100 425
servis@cz.husqvarna.com
Denmark
GARDENA DANMARK
Lejrvej 19, st.
3500 Værløse
Tlf.: (+45) 70 26 47 70
husqvarna@husqvarna.dk
www.gardena.com / dk
Dominican Republic
BOSQUESA, S.R.L
Carretera Santiago Licey
Km. 5 ½
Esquina Copal II.
Santiago
Dominican Republic
Phone: (+809) 736-0333
joserbosques[email protected]
Ecuador
Husqvarna Ecuador S.A.
Arupos E1-181 y 10 de
Agosto Quito, Pichincha
Tel. (+593) 22800739
francisco.jacome@
husqvarna.com.ec
Estonia
Husqvarna Eesti OÜ
Gardena Division
Valdeku 132
Tallinn
11216, Estonia
Finland
Oy Husqvarna Ab
Gardena Division
Lautatarhankatu 8 B /PL 3
00581 HELSINKI
France
Husqvarna France
9/11 Allée des pierres mayettes
92635 Gennevilliers Cedex
France
http : //www.gardena.com/ fr
N° AZUR: 0 810 00 78 23
(Prix d’un appel local)
Georgia
ALD Group
Beliashvili 8
1159 Tleilisi
Great Britain
Husqvarna UK Ltd
Preston Road
Aycliffe Industrial Park
Newton Aycliffe
County Durham
DL5 6UP
Phone:+44 (0) 344 8444558
customer.services@husqvarna.
co.uk
Greece
.
. 92
..10 4 4 2
. (+30) 210 5193 100
info@papadopoulos.com.gr
Hungary
Husqvarna Magyarország Kft.
Ezred u. 1 - 3
1044 Budapest
Telefon: (+36) 1 251-4161
vevoszolgalat.husqvarna@
husqvarna.hu
Iceland
Ó. Johnson & Kaaber
Tunguhalsi 1
110 Reykjavik
Ireland
Husqvarna UK Ltd
Preston Road
Aycliffe Industrial Park
Newton Aycliffe
County Durham
DL5 6UP
info.g[email protected]k
Italy
Husqvarna Italia S.p.A.
Via Santa Vecchia 15
23868 VALMADRERA (LC)
Phone: (+39) 0341.203.111
assistenza.italia@
it.husqvarna.com
Japan
KAKUICHI Co. Ltd.
Sumitomo Realty &
Development Kojimachi
BLDG., 8F
5 -1 Nibanncyo
Chiyoda-ku
Tokyo 102-0084
Phone: (+81) 33 264 4721
m_ishihara@kaku-ichi.co.jp
Kazakhstan
LAMED Ltd.
155/1, Tazhibayevoi Str.
050060 Almaty
IP Schmidt
Abayavenue 3B
110 005 Kostanay
Korea
Kyung Jin Trading CO.,LTD.
107-4, SunDuk Bld.,
YangJae-dong,
Seocho-gu,
Seoul, (zipcode: 137-891)
Phone: (+82) (0)2 574-6300
Kyrgyzstan
Alye Maki
av. Moladaya Guardir J 3
720014
Bishkek
Latvia
Husqvarna Latvija SIA
Gardena Division
Ulbrokas 19A
LV-1021 Rīga
Lithuania
UAB Husqvarna Lietuva
Gardena Division
Ateities pl. 77C
LT-52104 Kaunas
Luxembourg
Magasins Jules Neuberg
39, rue Jacques Stas
Luxembourg-Gasperich 2549
Case Postale No. 12
Luxembourg 2010
Phone: (+352) 40 14 01
Mexico
AFOSA
Av. Lopez Mateos Sur # 5019
Col. La Calma 45070
Zapopan, Jalisco, Mexico
Phone: (+52) 33 3818-3434
icornejo@afosa.com.mx
Moldova
Convel S.R.L.
290A Muncesti Str.
2002 Chisinau
Netherlands
Husqvarna Nederland B.V.
GARDENA Division
Postbus 50131
1305 AC ALMERE
Phone: (+31) 36 521 00 10
Neth. Antilles
Jonka Enterprises N.V.
Sta. Rosa Weg 196
P.O. Box 8200
Curaçao
Phone: (+599) 9 767 66 55
New Zealand
Husqvarna New Zealand Ltd.
PO Box 76-437
Manukau City 2241
Phone: (+64) (0) 9 9202410
support.nz@husqvarna.co.nz
Norway
Husqvarna Norge AS
Gardena Division
Trøskenveien 36
1708 Sarpsborg
Tel: 69 10 47 00
www.gardena.no
Peru
Husqvarna Perú S.A.
Jr. Ramón Cárcamo 710
Lima 1
Tel: (+51) 1 3320400 ext. 416
juan.rem[email protected]
Poland
Husqvarna
Poland Spółka z o.o.
ul. Wysockiego 15 b
03-371 Warszawa
Phone: (+48) 22 330 96 00
gardena@husqvarna.com.pl
Portugal
Husqvarna Portugal, SA
Lagoa - Albarraque
2635 - 595 Rio de Mouro
Tel.: (+351) 21 922 85 30
Fax : (+351) 21 922 85 36
Romania
Madex International Srl
Soseaua Odaii 117 - 123,
RO 013603 București, S1
Phone: (+40) 21 352.76.03
Russia / Россия
ООО „Хускварна“
141400, Московская обл.,
г. Х им ки,
улица Ленинградская,
владение 39, стр.6
Бизнес Центр
„Химки Бизнес Парк“,
помещение ОВ02_04
http://www.gardena.ru
Serbia
Domel d.o.o.
Autoput za Novi Sad bb
11273 Belgrade
Phone: (+381) 1 18 48 88 12
miroslav.jejina@domel.rs
Singapore
Hy-Ray PRIVATE LIMITED
40 Jalan Pemimpin
#02-08 Tat Ann Building
Singapore 577185
Phone: (+65) 6253 2277
shiying@hyray.com.sg
Slovak Republic
Husqvarna Česko s.r.o.
Türkova 2319/5b
149 00 Praha 4 – Chodov
Bezplatná infolinka:
800 154 044
servis@sk.husqvarna.com
Slovenia
Husqvarna Austria GmbH
Industriezeile 36
4010 Linz
Tel.: (+43) 732 77 01 01-485
service.gardena@
husqvarnagroup.com
South Africa
Husqvarna
South Africa (Pty) Ltd
Postnet Suite 250
Private Bag X6,
Cascades, 3202
South Africa
Phone: (+27) 33 846 9700
Spain
Husqvarna España S.A.
Calle de Rivas nº 10
28052 Madrid
Phone: (+34) 91 708 05 00
atencioncliente@gardena.es
Suriname
Agrofix n.v.
Verlengde Hogestraat #22
Phone: (+597) 472426
agrofix@sr.net
Pobox : 2006
Paramaribo
Suriname – South America
Sweden
Husqvarna AB
Gardena Division
S-561 82 Huskvarna
Switzerland / Schweiz
Husqvarna Schweiz AG
Consumer Products
Industriestrasse 10
5506 Mägenwil
Phone: (+ 41) (0) 62 887 37 90
Turkey
GARDENA Dost Diș Ticaret
Mümessillik A.Ș.
Sanayi Çad. Adil Sokak
No: 1/B Kartal
34873 Istanbul
Phone: (+90) 216 38 93 939
info@gardena-dost.com.tr
Ukraine / Україна
ТОВ « Хусварна Україна »
вул. Васильківська, 34,
офіс 204-г
03022, Київ
Тел. (+38) 044 498 39 02
info@gardena.ua
Uruguay
FELI SA
Entre Ríos 1083 CP 11800
Montevideo – Uruguay
Tel : (+598) 22 03 18 44
info@felisa.com.uy
Venezuela
Corporación Casa y Jardín C.A.
Av. Caroní, Edif. Trezmen, PB.
Colinas de Bello Monte.
1050 Caracas.
Tlf : (+58) 212 992 33 22
info@casayjardin.net.ve
Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice.
Copyright © 2019 Flymo S.A. All rights reserved.
Flymo
®
and other product and feature names are registered or unregistered trademarks of Flymo S.A.
ES300R-20.960.03/0420
© GARDENA
Manufacturing GmbH
D-89070 Ulm
http://www.gardena.com
