Loading ...
Loading ...
Loading ...
INSTALLATION INSTRUCTIONS
Installation Steps
STEP 4: Leveling your washer
See if the washer is level by checking the position of the tub or
using a leveling gauge.
1. Slide the washer into position.
2. Open the lid of the washer, and pour the water into the tub to just
below the pulsator level.
3. If the washer is level, the pulsator is positioned at the center of
the washer as shown in the figure right. If not, level your washer
by turning the front leveling feet clockwise or counterclockwise
as necessary.
Pulsator
loosen lock
Adjustable legs
Plug the power cord into a 3-prong, grounded 120Volt 60Hz
approved electrical outlet protected by a 15-amp fuse or
comparable circuit breaker.
Your washer is grounded through the third prong of the power cord
when plugged into a 3-prong grounded electrical outlet.
STEP 5: Powering your washer
Run a test cycle as following to check if your washer is properly installed.
1. Load about 6 pounds of laundry into the tub.
2. Press the Power button to turn on your washer.
3. Select the Rinse+Spin cycle by turning the Cycle Selector.
4. Press the Start/Pause button to start the test cycle.
5. The washer should not rock or vibrate excessively when water is supplied or when
washing or spinning, and should drain well during the spin cycle.
STEP 6: Running a test cycle
INSTALLATION INSTRUCTIONS
Installation Steps
6. Turn on the HOT and COLD water supplies and check all the
water supply intake connections and the faucets for water leaks.
STEP 3: Connect the drain hose
1. Connect the drain pipe onto your washer.
The drain pipe is attached as accessory with your washer.
Move the hoop forward
Insert the drain hose onto
the unit.
Move the hoop backward
A. Find the hoop on one end of the drain hose. Move the hoop
forward as shown in right figure.
B. Insert the end with hoop onto the washer. Be sure to slide
the drain hose over the sewer completely.
C. Move the hoop backward to fix the drain hose onto the
washer tightly.
2. Position the other end of the drain hose.
It can be positioned in three ways.
A. Over the edge of a wash basin
Secure the guide to the side of the basin wall
with a hook or to the tap with a piece of string
to prevent the drain hose from moving.
B. In a standpipe
The standpipe must b
e no shorter than 39 in.
(99cm) and no longer than 96 in. (245cm).
C. in a laundry tub.
The laundry tub must be no shorter than 39 in.
(99cm) and no higher than 96 in. (245cm).
Standpipe
Hose
Retainer
Tie
strap
96 in. Max
39 in. Min
Laundry tub
Hose
Retainer
Tie
strap
96 in. Max
39 in. Min
15
16
IMPORTANT: To ensure the correct water usage, connect both the HOT
and COLD water faucets. If either or both are not connected, an error
code can occur.
If you do not want to use the HOT water supply hose, insert the water
intake cap into the HOT water supply intake hole. In this case, you must
select the Tap Cold option for the water temperature.
IMPORTANT: Failure to slide the drain hose over the sewer
completely may result in water leakage.
Failure to move the hoop back will result in water leakage.
IMPORTANT: Make sure that the connection between
the drain hose and the wash basin, or standpipe, or
laundry tub is not airtight.
IMPORTANT: DO NOT use the washing machine without leveling.
It may result in malfunction caused by the production of excess
vibration and noise.
Use the leveling feet only when you level the washing machine .
If you raise the leveling feet unnecessarily, it may cause abnormal
vibration of the washing machine.
IMPORTANT: If water leaks while water is being supplied or drained, check the water connections.
Refer to the “Connect the water hose” and “Connect the drain hose” section for instructions.
If the washer rocks and vibrates excessively, level your washer again. Refer to the “Leveling
your washer” section for instructions.
Loading ...
Loading ...
Loading ...